CCCAM GENERATOR.rar
Kanisha Dezarn
Gentlemen, for two months I have been struggling to run cccam 2,3,0 in img, different. Unfortunately, I couldn't. As it is in ipk, it shows that it has loaded and if I am looking for it, it is not saved. As I put into individual folders, the green screen shows me. If any of the gentlemen has IMG bacukup with active cccam 2,3,0 to DM 800HD PVR Original. I am asking for sharing. I would be very grateful for your help.
Thank you mate teak-won-do. Unfortunately, as I wrote img. BlackHole-4.4-DM800-SSl84-20180326.rar has no cccam 2.3.0 and the given scm-cam-cccam_2.3.0-r0_mips32el.rar gives 0 record when saving, so it cannot save it in ipk. For this, I would like to ask if someone can write in img. I do bacukup of the entire img. And share me so I can save the whole img then I hope it will work. I also thank the admin for the hint, but I only have cccam 2.3.0 stably. Maybe someone will help a friend. I care a lot. Please.
This time it displayed that it unpacked, but after the gui reset, the cccam is missing. Strange because this cccam 2.3.9 that I downloaded from the page that Admin provided uploaded and works, but it breaks the image as described there. Stable, I only use cccam 2.3.0.
As I wrote above, when installing ipk. Some sees 1 and writes installed, others does not see 0, but does not install any. They are gone after the gui reset. Only properly installed cccam2.3.9 weird. And this is cccam2.3.8. also did not install. I don't know what to think anymore.
I did everything all over again. I installed img. BleckHole I tried to upload cccam 2.3.0. Unfortunately, it didn't work, so I uploaded cccam 2.3.8 and it worked, but after each cccam reset, green screen and gui reset. I also tried to upload what my colleague teak-won-do gave, i.e. img. Newnigma2 ipk everything seems to be ok, but when starting the green screen and so on. Maybe this ready img. with this cccam 2.3.0? Help, colleagues.
I have modified & updated the original script written by Youknowwho (R.I.P), to work with Ubuntu amd64.
I have tested this numerous times with no problems at all on two Desktop PC's, a laptop & VM Workstation.
This Script installs OSCAM 1.20-unstable_svn build #8905 (Compiled with all Omnikey & Smartreader Support) & cccam 2.1.3 (x32 & x64 compatable)
After final Reboot the oscam/cccam webif's are up and running.
Tip: Follow all the steps (including updates & other steps that you might be tempted to skip)
You can check your cccam Webif page by typing your server ip & cccam webif port no. (192.168.*.*:16001) in the address bar of your browser.
Username: admin
Password: admin
Now all you have to do Is configure your cccam.cfg and oscam configs to suit your setup & card readers.
The version of oscam in this script is the latest version, compiled with full support for all Card readers.
Ive spent the last couple of days trying to install the Automated Oscam/CCcam 2.1.3 Install Package For Debian 6 using Ten Below's excellent tut, but keep getting a problem with the script hanging so thought i'd try a different tack, so here i am.
Ive followed this tut from start to finish with absolutly zero problems (might i say really easy to follow for a real noob like me so many thanks) and i am now the proud owner of a P4 3.4GHz, with 160gb hard drive and 2gb of ram running Ubutu 12.04 server and oscam/cccam 2.13 :caz2:
so, the easy part out of the way thanks to the tut, what to do now... I have a brand new Smargo reader and a s*y uk white card but am still unsure what my next step is...
On my dm500 i was running cccam 2.1.3 and the clients are using a mix of dm500, spider boxes and a couple of blades.
Firstly, is Ubuntu 12.04 64-Bit - Automated Oscam/CCcam 2.1.3 a suitable choice for replacing my dm500, and if so what is the next step in getting my smargo running with my white card.... can i use the cccam.cfg already being used by my dm500 and do i need to install the oscam config for s*y uk, i am able to access the webif pages of both cccam and oscam but havnt got a real idea of what to do next...
i am not posting here without reading, its just that i have read and tried that much over the last couple of days my head is spinning and would really appreciate being pointed in the right direction..
Many many thanks in advance D
Glad to hear your cccam/oscam server is up n running m8.. thats a good 95% of the hard work done. Because there are 5 or 6 popular readers, I did not include that in the setup.. You will need to start a new thread if you have any problems setting up your smargo...
Ive followed this tut from start to finish with absolutly zero problems (might i say really easy to follow for a real noob like me so many thanks) and i am now the proud owner of a P4 3.4GHz, with 160gb hard drive and 2gb of ram running Ubutu 12.04 server and oscam/cccam 2.13
so, the easy part out of the way thanks to the tut, what to do now... I have a brand new Smargo reader and a s*y uk white card but am still unsure what my next step is...
Card sharing has virtually no impact on your broadband usage, I never measured it but I know from what I have read that you are sending minute packets of data. If you are concerned, you might want to restrict your other machines to using about 90-95% of your broadband. This will mean that no matter what you are downloading, there will be some broadband left for cccam.
Thanks thatfellow,
Your post is great for someone like me that comes from the ice age as far as computers are concerned. I followed your instructions which appeared to go ok, however when I try to web browse into oscam or cccam I get the message page cannot be displayed. I have used putty and confirmed that both are in the right location and that their configs show the web info ports are the same as I am using in the address bar (:8888 and :16001). I installed ubuntu 12.04. Hope this is ok.
Any ideas.
Thanks again for the great post,
HS5424
In the attached file you will get mgcamd 1.38 for mipsel receivers (VU+, CT and Dreambox receivers) + two config files. One is called mg_cfg, other one is cccamd.list. Both files need to be in var/keys
mg_cfg is already edited so it can be used immediately (mgcamd+cccam connection)! What you need to do is to make a C line and copy/paste it in cccamd.list file. Easy! I assume you know how to make C line? First you need to make F line on your server side where cccam is running. Then simply make C line from that F line!
For more instruction on C line and F line look here,