92S companion way

[Patrick M]

Any S folks out there have issues with water leaking in under the aluminum channel the plexiglass cover sits in? Noticed water on the steps and finally sat in the boat during rain today and noted water running in under the aluminum. Best guess is it's seeping around the screw but curious if any other similar experience. I'm uneasy removing the piece lest it bends and then will never seat properly. Don't even know what to call it to search for replacement parts.

Thanks 

Patrick

[furkolkjaaf]

Exact same issue here...for now I'm covering the deckhouse with a sheet...not a real fix indeed

Max

[Charles Cronin]

I think it is most likely rainwater collecting on the runners of the slide on the roof.  I have never found it to be significant, just a minor annoyance.  Check the flow of water along the runners to see if that is the cause.

Charles Cronin

Mobile

MLT +356.7953.5667

GBR +44.7711.589.198

Sent from Outlook for iOS

---

From: j92o...@googlegroups.com <j92o...@googlegroups.com> on behalf of furkolkjaaf <eliomas...@gmail.com>
Sent: Sunday, May 25, 2025 8:09:01 AM
To: J/92 Owners <j92o...@googlegroups.com>
Subject: [j92owners] Re: 92S companion way

 

--
You received this message because you are subscribed to the Google Groups "J/92 Owners" group.
To unsubscribe from this group and stop receiving emails from it, send an email to j92owners+...@googlegroups.com.
To view this discussion visit https://groups.google.com/d/msgid/j92owners/f0673404-72ea-41b6-bc6b-6d919716c80fn%40googlegroups.com.

[Philip Nann]

Same issue here. Teroson sealing tape worked for me. Sealant that can be formed by hand and wrapped it around the screws before screwing tight. Its permanently soft compared to sika or panthera and does not crack.

To view this discussion visit https://groups.google.com/d/msgid/j92owners/GVXPR08MB7727170B431A1832FDD301DCDB9AA%40GVXPR08MB7727.eurprd08.prod.outlook.com.

[JD Vincent]

I have not experienced this problem with my 2007 92S (hull # 66, built in France).  

The reason is there are small oval shaped drainage holes cut into the bottom outside edge of the aluminum channel in the companionway.  See picture.  The boat came this way from the factory as far as I know (I have owned it since 2011).

[d73p6...@gmail.com]

Have those as well. 

I did learn Monday the screw on the base of the flange was essentially free floating so I presume water seeping in there. Put some sealant in so will see. 

Patrick

On May 28, 2025, at 19:29, JD Vincent <davey....@gmail.com> wrote:

I have not experienced this problem with my 2007 92S (hull # 66, built in France).  

To view this discussion visit https://groups.google.com/d/msgid/j92owners/3737ea13-e222-4538-b4f8-9795f1f03462n%40googlegroups.com.

<IMG_3290.jpeg>

[Becky Walford]

Evening all, 

It is time to get busy with mastic. Remove the whole aluminium channel and re seal, 

Water on the ’shelf’ also builds up.

If this is leaking I am afraid that everything else is probably too.

I have just about done all the fittings in my J92s which is similar vintage!

Happy days.

Becky

To view this discussion visit https://groups.google.com/d/msgid/j92owners/237A193E-D4AF-44BA-9C71-3E213C524F2E%40gmail.com.

[Becky Walford]

Team

Sorry for this one, probably sorted now.

If you have water gathering on the inside of the internal moulding by the hatch, but accessed from the ‘back’, you washboard holding rail is leaking. 

In my experience sealant lasts about 6 years max.

So most of the fittings have been off and re goo-ed and re fitted.

The washboard rail is okay job put a good morning aside to remove, needing sharp knife and chisels. Then goo and replace, but also also time to clean goo up from you and the rest of the c/way area.

Have a good day.

Kind Regards

Becky

Brendas J

GBR 9972L

To view this discussion visit https://groups.google.com/d/msgid/j92owners/3737ea13-e222-4538-b4f8-9795f1f03462n%40googlegroups.com.
<IMG_3290.jpeg>