V360 Camera Reset
Karola Mura
Put the camera in the desired position and call the saveState() method.
Then the state of the camera is saved.
After this, if you call the reset() method at a desired point in time, the camera position is restored.
However, positioning the camera still only works the first click - moving the scene with the mouse then clicking the left button again (same angles) should move it back to same position each time surely?
1. Power on the camera and set the device to hotspot mode. When the (MV+ID) hotspot signal is found in the WiFi list of the mobile phone, it means that the device is in the waiting configuration state
1. The camera can only connect to 2.4G frequency WiFi, and does not support 5G frequency WiFi and mixed frequency WiFi, and does not support connecting to the guest network set by the router
2. Please do not exceed the device connection range, try to configure the network again after the device is closed to the router
3. The WiFi name cannot contain Chinese characters, and the WiFi name cannot be set to hide
4. Check whether the router restricts device access
5. If the device fails to receive configuration information or fails to be configured for multiple times, it is recommended to use AP hotspot mode configuration
Note: The network cable connection has priority. When the network cable is connected, other connection methods will be blocked. If you need to switch to the wireless connection method, please disconnect the network cable first
Note
1. To connect the device in the AP hotspot mode, the mobile phone must remain connected to the device hotspot. Please ensure that the mobile phone is within the hotspot connection range to avoid disconnecting the device
2. Device hotspot means that the signal from the camera cannot connect to the Internet, and other networked applications cannot be used when the phone is connected to the hotspot. Please pay attention
1) 2.4G is a wireless technology. Because its frequency band is between 2.400GHz and 2.4835GHz, it is referred to as 2.4G wireless technology
2) 5G WiFi refers to the wireless technology developed based on the IEEE 802.11ac standard. Because the IEEE 802.11ac technology itself works in the 5G Hz frequency band, it is also called 5G WiFi
The WiFi module used by the V380 product only supports connection to 2.4G WiFi, and cannot recognize or connect to 5G WiFi. Therefore, 5G WiFi or mixed-band WiFi cannot be used to configure the device network
After connecting the device with the mobile phone V380App, click [Settings]-[Device IP] interface setting
requirements in the lower right corner of the device list screen :
1. IP: set according to the gateway itself
2. Subnet mask: 255.255.255.0
3. Gateway : Normally router IP
4, DNS: Generally router IP
If you did the following operations
a. Replaced the router
b. Modified WiFi username and password
c. Changed the network configuration information
Please restore the wireless camera to the factory default settings and reconfigure the network
After the device is added to the device list, you can view the camera network status in the device window
1. Connecting: it means that the APP is acquiring the device status, and the current status of the device will be displayed after the acquisition is successful
2. Internet offline: indicates that the device is not connected to the Internet, and the APP cannot connect to the device in this state
3. Internet online: indicates that the device is connected to the Internet, and the APP can connect to the device remotely in this state
4. LAN online: it means that the device and the mobile phone are in the same local area network. In this state, the camera and the mobile phone are connected point-to-point
1) Please try to restart the camera to confirm that the camera has been started correctly and connected to WiFi
2) Turn off the router AP isolation function
3) Check whether the mobile phone can be connected to the Internet normally, and the APP has obtained the network permission
1) Please try to restart the camera and confirm that the camera is already in station mode
2) Check whether the router is connected to the Internet
3) Check whether the router restricts the device from connecting to the Internet
4) Turn off functions such as router firewall, blacklist, mac address binding, etc.
5) If the above methods fail to solve the problem, please contact the technician
1. Please try to close the APP and open it again
2. Please try to power off and restart the camera once
3. Please do not exceed the router connection range, try to connect the device close to the router
4. Please log in to the router background to check if there is a restricted device connection
Network fluctuation or insufficient mobile phone memory during connection may cause the screen to freeze
1. Please do not exceed the router connection range, try to connect the device close to the router
2. Please try to switch the screen to SD stream preview
Please try to configure the network near the router.
The V380 wireless camera can only connect 2.4G frequency WiFi signal.
Do not use Chinese characters for the router name.
Check whether the router has device connection restrictions.
Some routers may be difficult to configure, AP hot spot mode is recommended for the configuration
2, outdoor wireless camera:
(a) Method one: [Long press the reset reset button for about 10s] to restore the device to the factory settings. wait until the tail indicator light which flashed rapidly turns to constant on, Short press the button again,When the tail indicator flashes slowly, the device has been switched to station mode.
(b) Method 2: In the state that the device is connected to the network, in the lower right corner of the V380App device list screen [Settings]-[Change Device Network]-[Switch device to route mode and select route to fill in password]-[OK].
(a) Method one: [Long press the reset reset button for about 10s] . Press the RESET button for 10 seconds to reset the device to the factory settings. The tail light indicator which flashed quickly turned to constant onit means the camera is in hot spot mode.
1. Android user: Click [+] in the upper right corner -> [Access-Point established] -> [Select device] -> [Select the route to be connected and enter the route password] -> [Click OK] After successful connection,
Note:
1. Only Anyka and GM support the ONVIF protocol. Other solutions do not support ONVIF protocol can not connect to NVR
2. Anyka 2505 version, GM 3505 firmware does not open RTSP protocol, if you need to connect NVR please contact the technician to provide upgrade package to open RTSP
Method one: Manually add
1, open the [device list] interface, click [+] in the upper right corner
2, select [WiFi connection completed] or [other ways]
3, after entering the ID and password [OK add], the system jumps to the device List, the newly added device is displayed in the first place in the device list.
Method 2: Local Area Network Addition (Only if the camera and the mobile phone are connected to the same network)
1. Open the Device List screen, Pull down the screen to refresh the device list.
2. The system automatically searches for the LAN device and automatically adds the device display. In the first place of the device list , successful adding, the preview needs to enter the correct access password (as shown below)
press and hold the Wi-Fi button on the body of the camera for 8 seconds while the camera is on. The camera will reboot. It will reset the wifi settings to factory default. The password is just the digits of the serial number. it will be in 2.4GHz.
Preview mode is ideal for installers when fine tuning the camera view during the installation. No login is required to access the camera view in preview mode. It is available only in factory defaulted state for a limited time from powering up the device.
Capture mode sets the boundaries of the video image, affecting how the image is captured and processed. Beyond aspect ratio and resolution, it affects many other settings as well, such as, exposure zones, guard tours, image overlays, motion detection (include areas and exclude areas), preset positions, privacy masks, and view areas. The following capture modes are available:
To improve image quality for specific surveillance scenes, use exposure modes. Exposure modes lets you control aperture, shutter speed, and gain. Go to Video > Image > Exposure and select between the following exposure modes:
Depending on the installation environment and the conditions around the camera, for example external light sources in the scene, you can sometimes improve the image quality if you manually adjust the intensity of the LEDs. If you have problems with reflections from the LEDs, you can try to reduce the intensity.
Your camera uses visible light to deliver color images during the day. But as the visible light diminishes, color images become less bright and clear. If you switch to night mode when this happens, the camera uses both visible and near-infrared light to deliver bright and detailed black-and-white images instead. You can set the camera to switch to night mode automatically.
Dynamic range is the difference in light levels in an image. In some cases the difference between the darkest and the brightest areas can be significant. The result is often an image where either the dark or the bright areas are visible. Wide dynamic range (WDR) makes both dark and bright areas of the image visible.
4a15465005