includes a watchdog to prevent TX runaway. If the HL2 doesn't hear from the host software within a specified amount of time (very short), then it will disable TX. This can be disabled

with the watchdog setting >>>>>>>>> >>>>>>>>> The HL2 and the pc are connected to the same network switch. I >>

Comparing your build file list to mine, one of the first files to be compiled should have been main.c. Your build did not find main.c so failed on that

Dear Joel, see attached. Also watched ON7OFF on Toutube, great videos. Op dinsdag 29 oktober 2024 om 20:58:30 UTC+1 schreef Joel Caulkins: > Hi, I

Dear all, As Kurt is a very modest Ham operator I want to promote his excellent Thetis YouTube tutorials " from zero to hero" Tutorials .

Check the manual. WSJT-X and JTDX are similair. 73 Ronald PH7R Op vrijdag 6 september 2024 om 05:55:23 UTC+2 schreef Al Goodvibes (14DWT2901): >

Did you set the drive in Thetis? See very usefull manual. 73 PH7R Ronald Op donderdag 22 augustus 2024 om 11:46:15 UTC+2 schreef Ken Short: >

Sorry this version which isn't reduced/ compressed may be easier to see of the screen shots Also, the latest version be available on the Hermes

Hi Nikos, I have a attached a document from Rick N8SDR, which goes though the install procedure and has info on setting up Thetis. Hope this helps.

It looks like you are not running the correct version of Thetis. I have a attached a document from Rick N8SDR, which goes though the install procedure

FPGA gateware watchdog timer >>> time out. (Question: What is this minimum rate ?) >>> Both the transmit and receive data packets of 1032 bytes contain a 4 >>

out the watchdog timer but think that the DLL I am using has > that taken care of. > > 73 > Cliff VK2NP > > On Saturday, August 12, 2023 at 2:50:30 PM UTC+10 softerh...

> Network Watchdog, Auto Detect Protocol clicked. Tried static IP with >> address reported by V2.9.0.6. Same error. Ran Firewall Check - said it >> was configured

disable the watchdog timer immediately (no need to ever send TX packets) by setting the bit in the Metis start packet. I think this is what CW skimmer does. The openhpsdr radios always

disables the watchdog so you do not need to worry about sending packets to the HL2. It is based on hermeslite.py, a Python library which I use for all command line testing: https://github

off the watchdog timer and found it more reliable for two days, >> then returning to its intermittent freezing in the SparkSDR. A few on-off >> cycle of SparkSDR will bring

disable the watchdog to use it as no software > sends TX packets at the right ratio. An example of how to do that is in > hermeslite.py: > > https://github.com/softerhardware

. The watchdog and reset_on_disconnect require this too. Add your code as follows: def HeartBeat(self): self.hermes_temperature, self.hermes_fwd_power, self.hermes_rev_power

> Such watchdog is in the HL2 firmware, but it doesn't resolve this type > of problems, because it's the quisk which is sending the packets and > the > ethernet connection

the > watchdog timer in SparkSDR help? Even during TX, the unit is > allowed to reach 55C before shutting TX off. > > The heat sinks included from Makerfabs are standard Raspberry

or the watchdog times out. This >> is essentially a very long PTT hang time. It is meant to replace relay >> clicks with dead time in TX audio. Second when told by software

Turned disable Watchdog on, ran 10 minutes and stopped processing. >> Toggled power button some time later and it resumes. Not other changes >> made. EP still 327. Nothing

using the watchdog timer. > > The version should switch to 72 and patch to 8, but the version remains at > 70, so I'm blocked for futher operations. > > Alan M0NN says

>> watchdog. >>>>>>> 73 de Sven SM6FMB >>>>>>> >>>>>>> >>>>>>> >>

as a watchdog timer will not be renewed. If not, then it may indicate a hardware issue. How high is the temperature? TX is disabled when the temperature reaches 55C. There is a TX inhibit

is a watchdog counter in the HL2 and it must receive packets to stay in TX, so something is still sending packets. I think you said you are using SDRConsole on Windows? Can you open up task

than the watchdog, I have never >>>>>> actually tested that the disable watchdog feature in recent versions of >>>>>> Spark actually works

disable the watchdog timer so should work. The latest stable gateware release is recommended: https://github.com/softerhardware/Hermes-Lite2/tree/master/gateware/bitfiles

reset the watchdog timer), you >>> will have to either update CW skimmer to send a filter setting which >>> activates the HPF, or you may be able to get by using hermeslite

on disabling watchdog timer in that >> variant, and also see if we can reduce to 10 192kHz receivers for skimming. >> > >> > 73, >> > >> >