built the transverter board for 2m some time ago. It works, but for transmission the suppression of the 116MHz oscillator signal is not sufficient. In Germany you need to have at least

>> transverter (splif IF). The main RF goes to my HF multiband antenna. You >>>> can switch between them using SDR app features or a script, or in my case I >>

without a transverter we won't see over 30MHz? I'm > told that the HL2 only goes up to 38MHz and doesn't cover 6M. > > The highest frequency I'm interested

Note the S-meter reading is in dBm, while the noise floor is in dBm/Hz (or dBm/frequency-interval), so do not even try to get the same numbers there.

duplex Microwave Transverter Controller. It is the V3 version. There is also some more detailled information about the full-duplex 144/28 MHz transverter under the material "

European 2m transverter into >>> service and its PTT voltage was 13.6V. It is more common than we realize. >>> A Schottky diode with small forward voltage drop is

driving a transverter. Took the opportunity of changing the mac address 2, so I've now got bot of them on the same network 73, Charlie GI4FUE On Thursday, 7 November 2024 at 00:25

& a transverter. You will have your dream radio. On Tuesday, November 12, 2024 at 1:44:09 PM UTC-5 Randy Best wrote: > OK, OK, OK I have to ask. I love my HL2 and latest Thetis. >

a 6M transverter using split IF (low level TX out and Aux RF in), and an HF antenna on the ANT jack.  I switch between them through the SDR app, Thetis in this example.   Here is what I have set

Dear Joel, see attached. Also watched ON7OFF on Toutube, great videos. Op dinsdag 29 oktober 2024 om 20:58:30 UTC+1 schreef Joel Caulkins: > Hi, I

with a transverter for a 2m >> repeater. All works fine in that I hit the repeater and I hear and am >> heard. I was told I had low audio and sounded like I was narrow band, but

Dear all, As Kurt is a very modest Ham operator I want to promote his excellent Thetis YouTube tutorials " from zero to hero" Tutorials .

Check the manual. WSJT-X and JTDX are similair. 73 Ronald PH7R Op vrijdag 6 september 2024 om 05:55:23 UTC+2 schreef Al Goodvibes (14DWT2901): >

more for transverter ops. The current rig now has the > Plus, IO, and Filter board. I also have the v1 that someone placed in a > very nice case, it's what turned me on to this project

Did you set the drive in Thetis? See very usefull manual. 73 PH7R Ronald Op donderdag 22 augustus 2024 om 11:46:15 UTC+2 schreef Ken Short: >

Rx for transverter input in xvtr form (I/O > Board only) > > *WARNING* > > This release now contains an installer and will install in the same place > as the official

using a transverter. Does Thetis provide that signal to > the board when a transverter frequency is selected in the VFO? Or must the > Pico be programmed to provide that signal

mode with transverter. In the XVTRs menu pa off don't work, any idea or is it a softwareproblem ? and not possible. The same with PowerSDR mRX PS. I use a HL2 with filterboard. 73 Peter

and a transverter. One day a few month ago the hermes lite >>>> 2 quick sending anything to the panadapter. >>>> >>>> The Hermes lite is discovered

Sorry this version which isn't reduced/ compressed may be easier to see of the screen shots Also, the latest version be available on the Hermes

opened the transverter and the RXGain pot in it is near the top. On my flex the RX signal is very strong. I'm waiting for another satellite to come over to check again. The TX gain pot

has no transverter for > typical satellite frequencies. > > You might want to contact Daniel Estevez who is a HF HL2 user but also > quite active with satellites and SDR.

via a transverter, the other on and off the HF bands with the 10Rx HL2. No database reset from Beta 2 required so far.   From: herme...@googlegroups.com <herme...@googlegroups.

a multiband transverter with PTT on the > same band decoder cable, so I monitor TX frequency and EXTTR in custom > firmware and send out a GND for PTT and Band from J6 pins I arbitrarily

5 band transverter. I have posted the code changes in previous posts >> here. In my case I am emulating the K3 VHF BCD patterns. There are high >> and low outputs on the IO Board

Jim N1ADJ, I can confirm the error code is still 0xF0. I'm running the latest version of Reid's build as of this writing. Just updated quisk

Hi Nikos, I have a attached a document from Rick N8SDR, which goes though the install procedure and has info on setting up Thetis. Hope this helps.

You can wire up a "splitter" cable to share the HL2 DB9 with both amps. With 9 pins I suspect it is plenty to handle both amps. You can wire

It looks like you are not running the correct version of Thetis. I have a attached a document from Rick N8SDR, which goes though the install procedure

-1296 transverter band map. It is only a small amount of code and it > is easy to swap out the VHF band codes for HF band codes and add a few more > bands with cut and paste. I use the BCD