Error 10124

[Mr Langlois]

Hello

Can you help me please?

Tanks

Fraçois

10124: Intake air temperature sensor faulty

This problem occurend once

Logistic counter: 40

Symptom: No signal or value

Mil set: no

Odometer: 53000 km

AD value intake Air temperature: 4,98V

[Haakon]

I KNOW others can answer this better than me :-)

I personally would not worry at all!

It says

"This problem occurend once"

It is not a "present" fault, so unless you have problems with your bike ...  try forget it :-)

--------

That specific sort of fault will is not a serious problem.

If the same fault pop up again, just try disconnect the plug from the temp sensor and put it back.

It CAN be caused by a bad (coroded connector)

Haakon

(Always tell what bike you have :-) 

 

--
You received this message because you are subscribed to the Google Groups "GS-911 Field Diagnostic Tool for BMW motorcycles" group.
To unsubscribe from this group and stop receiving emails from it, send an email to gs-911+un...@googlegroups.com.
To post to this group, send email to gs-...@googlegroups.com.
Visit this group at http://groups.google.com/group/gs-911?hl=en.
For more options, visit https://groups.google.com/groups/opt_out.
 
 

[Mr Langlois]

Bonjour J'ai un R1200GSA 2007 et je n'ai pas de problème. la moto fonctionne correctement. Cette erreur ne semble pas jusqu'à ce que je télécharge GS-911 121.5 version. Mon GS est équipé du module d'accélérateur qui trompe le capteur de température de l'air. Je vous remercie pour votre réponse et désolé pour mon anglais. Traducteur Google est mon ami. ;-) Merci François

Le Lundi 18 février 2013 22:40:34 UTC +1, M. Langlois a écrit:

Bonjour

Pouvez-vous m'aider s'il vous plaît?

Réservoirs

Fraçois

10124: capteur de température d'air d'admission défectueuse

Ce problème occurend fois

Contre Logistique: 40

Symptôme: Pas de signal ou de la valeur

Mil ensemble: aucune

Odomètre: 53000 km

Valeur AD température d'admission d'air: 4,98 V

[Jos Palmaers]

I’ll translate to English for this guy, since Google Translator is not my best friend.

 

Hello,

 

I own a R1200GSA2007 without problems and the bike runs fine.

This error didn’t show up until I started using GS-911 version 121.5 (I suppose he means version 1211.5).

My GS is equipped with an accelerator module that fools the intake temperature sensor.

I thank you for your answer and excuse myself for my bad English.

 

Thank you,

 

François

 

I have no experience myself with these intake temperature modifying devices, but I suppose they could generate an error code that can safely be ignored if the bike runs fine.

 

Anyone who has experience with this stuff, please comment.

 

Best,

 

Jos

--

[Stephan Thiel]

Where is the AutoScan?

pls see point 3 on
 http://www.hexcode.co.za/products/gs-911/support-forum-rules

--
You received this message because you are subscribed to the Google Groups "GS-911 Field Diagnostic Tool for BMW motorcycles" group.
To unsubscribe from this group and stop receiving emails from it, send an email to gs-911+un...@googlegroups.com.
To post to this group, send email to gs-...@googlegroups.com.
Visit this group at http://groups.google.com/group/gs-911?hl=en.
For more options, visit https://groups.google.com/groups/opt_out.
 
 

-- 
========================
Stephan Thiel
www.hex.co.za
www.hexcode.co.za
+27 21 880 1433 (tel)
+27 86 614 1109 (fax)
========================
 
This email and contents are subject to the HEX EMAIL LEGAL NOTICE.
View at http://www.hex.co.za/legal/emailnotice.html

[damted]

Hi Francois,

I also equipped my R1200R with an accelerator module that fools the intake temperature sensor.

When you use your GS-911 and run it in real time mode, you can see outside temperature and air intake temperature.

Because you "fool" your ECU, the air intake will probably show a much lower value (20 to 30 degrees lower)  then the outside temperature.

When problem only occured once, please reset the fault code, it will do no harm.

When you disconnect this air intake sensor connector for a short moment, it will log a new fault code in the ECU.

regards,

Ted

Op maandag 18 februari 2013 22:40:34 UTC+1 schreef Mr Langlois het volgende: