Gqrx 2.15.8 unterstützt keine Kurzwelle mehr - SDR USB RTL2832U R820T2 Chipsatz XR-105 UV Tuner
92 views
Skip to first unread message
H. Schulz
Apr 7, 2024, 2:47:40 AMApr 7
to Gqrx SDR
Bis zu der Gqrx-Version, die 2018 aktuell war, konnte ich meinen SDR-Rx "SDR USB Tuner Empfänger RTL2832U R820T2" tadellos auf Kurzwelle benutzen.
Mit der aktuellen Version furnktioniert das nicht mehr! Ich kann keine Frequenzen unter 24 MHz mehr einstellen. Wenn ich das Häkchen auf "no limits" setze, kann ich zwar idiese Bereiche einstellen, habe aber keinen Empfang. Folgerichtig wird der Modus nicht eingeschaltet.
Ich habe, soweit ich es verstehen konnte, sehr viele Beiträge darüber gelesen, dass hunderte oder tausende andere Anwender genau dasselbe Problem haben. Aber welchen Lösungsvorschlag ich auch fand, keiner hat eine Lösung gebracht. Ich habe auch bei "device-string" eingetragen: direct_samp=2. Ich kann mich schwach erinnern, dass aber in der alten Version aus 2018 etwas Anderes eingetragen wurde, aber ich kann mich daran nicht genau erinnern. Notiert ist es leider nirgends.
Was muss da wirklich eingetragen werden., damit ich wieder Kurzwelle damit empfangen kann? Das Gerät kann es zweifelsfrei. Es hat 2 Antenneneingänge.
Up to the Gqrx version, which was up-to-date in 2018, I was able to use my SDR-Rx "SDR USB Tuner Receiver RTL2832U R820T2" perfectly on shortwave.
With the current version this not longer works! I can no longer set frequencies below 24 MHz. If I set the check mark to "no limits", I can set these ranges, but I have no reception. Consequently, the mode is not switched on.
As far as I could understand it, I have read a lot of posts about the fact that hundreds or thousands of other users have exactly the same problem. But whatever solution I came up with, no one came up with a solution. I also entered "device-string": direct_samp=2. I can faintly remember, but something else was entered in the old version from 2018, but I can't remember it exactly. Unfortunately, it is not noted anywhere.
What really needs to be entered there. so that I can receive shortwave with it again? The device can do it without a doubt. It has 2 antenna inputs.
With the current version this not longer works! I can no longer set frequencies below 24 MHz. If I set the check mark to "no limits", I can set these ranges, but I have no reception. Consequently, the mode is not switched on.
As far as I could understand it, I have read a lot of posts about the fact that hundreds or thousands of other users have exactly the same problem. But whatever solution I came up with, no one came up with a solution. I also entered "device-string": direct_samp=2. I can faintly remember, but something else was entered in the old version from 2018, but I can't remember it exactly. Unfortunately, it is not noted anywhere.
What really needs to be entered there. so that I can receive shortwave with it again? The device can do it without a doubt. It has 2 antenna inputs.
righthal...@gmail.com
Apr 7, 2024, 9:46:03 AMApr 7
to Gqrx SDR
direct_samp=2 is correct, but the current SoapyRTLSDR has no ability to handle two antennas - perhaps it is selecting the wrong one by
default.
default.
Reply all
Reply to author
Forward
0 new messages