Ubnt Litebeam M5 Firmware Download

0 views

Skip to first unread message

Ophelia Gurin

unread,

Aug 3, 2024, 1:10:12 PM8/3/24

to geocyteme

i've recently came up with an idea how to flash locked/signed firmware on litebeam ac gen2. basically you start flashing same ubiquiti fw that is already on device and interrupt the process, that leaves mtd partitions unlocked and you can flash another image to these using dd. more info in this GH comment-> -493658317

I'm getting similar results. Using files 3.15.1.0b0-ubnt-nano-m-xw-squashfs-factory.bin and 3.16.1.1-ubnt-nano-m-squashfs-factory.bin. I've run tftp from Windows 7 and from a Raspberry pi 3. I've run it both in text and binary mode. On windows I get timeouts after sending a lot of packets. On the pi I thin it goes all the way through, the last packet is smaller than 512 bytes. and I get firmware check failed. Target is a Ubuiqiuty nanostation m2.

I have a litebeam m5 23 db and I would like to install openwrt .. once I installed it from the same administration page but I had to reset it from the factory and it had air os again and now it does not let me install lede that could do? greetings and thanks

Unfortunately I have no serial access. I don't know how to open the feedhorn and get it waterproof after opening again. - So as far as I understood in some other discussions we need a beta-image (I registred and accept terms for beta, but couldn't find betaimages at ubiquiti-pages), flash an unsigned old image (offically available on OEM-site) and from there flash the openwrt*.factory image. A direct flash of unsigned images don't work, it stops with error code 43.

Hey Guys,
Have you been successful in installing OpenWRT on Litebeam M5? I have been unsuccessful in downgrading to xw.v5.6, any attempt to install any firmware lower than xw. v6.17 I lose GUI and SCP access, my only successful procedure has been through TFTP.

I have finally been able to successfully install OpenWRT19.07.x on the Ubiquiti Litebeam M5. I have tried several installation processes I could find on the web which was not successful for me. I was able to install OpenWRT after downgrading to XW.v6.1.3 via TFTP.

The popular suggested method: "Downgrade to unsigned version via AirOS web GUI only possible using v6.0.6-beta firmware(FW). First upgrade/downgrade to v6.0.6-beta, then downgrade to unsigned v5.6.15. Just then it will be possible to downgrade to an even lower AirOS version, e.g. v5.5.11." was unsuccessful for the Litebeam M5 with Atheros AR9342 rev 3.

It is probably the same hardware platform and can run the same firmware as the Nanostation M5 loco XW, which has been ported. But I offer no guarantee of that. If you have the old bootloader which does not check firmware signature, you can easily TFTP debrick direct back to OpenWrt.

The preferred language in the OpenWrt forum is english.
When writing in your native language, please always provide an english translation.
This way other users all around the world can take part in the discussion and possibly benefit from the outcome, without having to use a translator.

The Nanostation loco M XW appears to be the same chipset and general hardware platform as the Litebeam M5, except it has a dish antenna system (which makes no difference to software). I was suggesting to try the ath79 loco-m-xw build, since there is no ath79 lbe-m5 build. I do not have a Litebeam M5 to try this myself.

Burning Man IT provides an Internet backbone for Black Rock City participants. While we try our best to provide great service, we cannot guarantee a specific level of service in terms of bandwidth, latency or uptime, nor can we offer any support. Participants themselves organize "Doctors Hours" most days of the event for mutual help.

As you can imagine, getting Internet service in such a remote area is very challenging. It is a limited resource and we need to conserve it as much as possible so please be kind and use it sparingly.

To participate, you need to have a specific kind of microwave radio, mount it in your camp, aim it and keep it powered. This radio acts as a router and DHCP server and has a wired ethernet port. To get WiFi, you'll need one or more WiFi access points. To keep our backbone working well, it's best to configure access points to use 2.4 GHz only (and disable 5 GHz). In the spirit of Radical Inclusion, we encourage you to share the Internet not just with your campmates, but with everyone..

The radio we recommend is the Ubiquiti NanoBeam AC Gen2 NBE-5AC-Gen2-US. It is small and somewhat resistant to the high winds. It's available for about $100 from Ubiquiti, Amazon, or other resellers. In light of the current supply chain shortages, you can also use:

Different zones of Black Rock City are covered by different antennas. Each zone requires a different configuration file. The map below is a rough guideline. You can try different configurations to find the strongest signal. Mutant Vehicles should use the Deep Playa sector.

Plug your laptop into the LAN port of the PoE injector. Give the laptop the static IP address 192.168.1.21, netmask 255.255.255.0. Open a web browser and go to . If it's a device with old firmware, login as user ubnt, password ubnt. Devices with newer firmware will prompt you to create a username and password. Do so. You'll need to remember both for about 10 minutes. Go to the System tab. The first two letters of the Firmware Version field show the board version. Click on Upload Firmware and upload the firmware version recommended below. Do not disrupt power or cables during firmware upgrades; otherwise your device could be bricked.