Usb To Serial Converter Hl-340 Driver

0 views

Skip to first unread message

Gualtar Pennington

unread,

Aug 3, 2024, 2:42:24 PM8/3/24

to gastpooddiisubt

Don't do this. You will run into USB driver issues on RPi3. Use a TTL-to-RS232 converter (at GPIO RX/TX). It's cheap, and you will find a lot of manuals how to connect and test that converter. There are small versions that you can mount in your RPi3 case.

In this tutorial, we'll show you how to install CH340 drivers on multiple operating systems if you need. The driver should automatically install on most operating systems. However, there is a wide range of operating systems out there. You may need to install drivers the first time you connect the chip to your computer's USB port or when there are operating system updates.

There are a few variants of the CH340. The CH340G requires an external crystal oscillator to function while the CH340C includes a built-in crystal oscillator. However, both function in the same fashion - they convert USB data for a serial UART and vice versa!

These operating systems have the CDC drivers pre-installed, which means you shouldn't need to install any extra software. However, there are a wide range of operating systems out there, so if you run into driver problems, you can get the archived drivers linked below:

Alternatively, if you have the Arduino IDE installed, you should also see a change in the number of available COM Ports (you may need to restart the Arduino IDE for the board to populate). Without the CH340 connected to your computer, click on Tools > Port. Take note of the Serial Ports available.

Connect the CH340 to your computer's USB port. Click on somewhere else on the screen for the menu to refresh itself. Then head back to the menu by clicking on Tools > Port. A new COM port should pop up. By process of elimination, the CH340 should have enumerated to the new COM port! Feel free to click on the COM port to select if you are uploading code to a microcontroller. Depending on your computer, the COM port may show a different number.

You can also verify if the USB-to-serial converter is working by doing a serial loop back test or echo test. If you are using the breakout board, you can add a jumper between the Tx and Rx to try and echo a character in a terminal program. For more information, try checking out the Hardware Test for the serial basic hookup guide.

If you have found the file in the path, you will need to run each of the following commands in the CLI/Terminal to remove old CH340 drivers. In this case, there was only the usbserial.kext file but it does not hurt to run both commands. Make sure to have administrative privileges to ensure that the drivers are removed.

Check if the old drivers were removed in the paths by using the ls command with your respective OS version. You will notice that the *.kext file is removed from the respective paths. In this case, the usbserial.kext was removed from Mac OSX High Sierra.

There are some reported cases of serial communication failure when using the factory drivers in Linux. If you encounter this problem, you can try installing patched drivers as explained in this forum post. Here are the steps (to run in the command line):

Depending on your root permissions, you may need to configure the serial port with the following two commands. Make sure to adjust the $username with respect to the user ID that is currently logged in.

Plug the CH340 back to your computer's USB port. Then run the following command in the CLI/Terminal on any Linux distribution. Check for the following changes (your board may show up under a different device name).

We have had a few reports on Windows 10 where the driver will automatically install and the board will show up under a new COM port as USB-Serial CH340, but with a different device name. However, the board cannot be accessed on the Arduino IDE. Others have had issues where the installation process hangs.

Based on the customer experiences, this might be specific to the manufacturer and are usually isolated cases. Users seem to be able to eventually get the board recognized by a combination of giving the computer time to finish the install (close to 20 min), plugging the board back in multiple times, reinstalling the drivers, and/or resetting the computer multiple times (repeat both steps).

If you installed the drivers for the CH340 on your computer but have issues connecting via serial terminal or uploading code using the Arduino IDE, there may be an issue with your user settings preventing you from using the CH340. You may receive an avrdude: ser_open(): can't open device error similar to the output shown below.

If you are uploading to certain boards like the Apollo3 on the Artemis development boards with fast baud rates, there are some platforms (Linux flavors) where the standard CH340 USB to serial drivers don't operate well at speeds higher than 115200. So if you run into upload problems, consider reducing the upload speed. For more information about upload issues, see this forum post and consider upgrading with these drivers for Mac OSX or these for Linux.

USB-to-serial converters like the CH340 are great for uploading code to a microcontroller or viewing data from a GPS on a serial terminal. Check out these tutorials to dive even deeper into the world of microcontrollers or send serial data to your computer with a GPS!

We present a serial link transmitter designed for CMOS pixel sensors in a 0.18 m CMOS Technology. The transmitter includes a digital interface block with Reed-Solomon encoder, a Phase-Locked Loop (PLL), a serializer and a Current Mode Logic (CML) driver with pre-emphasis. Functionalities of the transmitter is verified by simulation, consuming 174 mW from a 1.8 V power supply. The transmitter...

A 4-channel parallel 56 Gb/s optical receiver for VCSEL-based optical links is presented. The receiver has been manufactured in a standard 65nm-CMOS process. Simulation results with layout parasites and a model of a wire-bonded photo diode demonstrate that the single channel works at bit rate of 14 Gb/s and has an input sensitivity of better than 20 uApp, an input-referred noise of 2.3 uArms...

The MPA is the pixel readout ASIC for the hybrid Pixel-Strip module of the Phase-II CMS Outer Tracker upgrade at the High Luminosity LHC (HL-LHC). It employs a novel technique for identifying high transverse momentum particles and provides this information at a 40$\,$MHz rate to the L1-trigger system. The chip also comprises a binary pipeline buffer for the L1-trigger latency, and a data path...

The Jiangmen Underground Neutrino Observatory (JUNO) is a multi-purpose underground experiment based on a 20,000 ton liquid scintillator with the one main objective to determine the neutrino mass hierarchy. The signal detection is performed by photomultipliers with directly attached readout electronics. The central component for the digitization process is a receiver chip with a low power...

In this contribution we present the development of a custom ASIC chip meant to be bump-bonded to segmented Ultra-Fast Silicon Detector, aiming to achieve a combined time resolution of $\sigma \sim$ 30 ps.

The Liquid Argon Pixel (LArPix) prototype ASIC implements 32 channels of analog front end circuitry and backend digitizers at a power consumption of less than 50 uW/channel. LArPix is envisioned as a component of a potential DUNE near detector TPC module. Demanding noise, power, and dynamic range requirements are imposed by myriad particle interaction scenarios. Widely varying track...