Eppendorf 5810

[Jennifer Downey]

Themotor is not controlled by the lid switches. Rather, the slide mechanism partly extends over the PCB. The slide is the flat metal plate the motor moves up and down. There are two hall sensors on the PCB and a magnet on the slide mechanism. The hall sensors are used to indicate if the motor/latch is in the full up or down position. If the magnet has come loose and is not aligned (or it fell off), then the controller will not be able to determine the latch mech position. Second to last solution given below.

FYI: I had a problem where the lid motor would 'step' and stop. It would not run to the open/close positions. Called Eppendorf and they said replace the lid motor. I pulled the lid motor and ran it using a bench supply and it ran fine. BUT, the current draw seemed erratic and inconstant between power cycles. If I was going to replace the $250 motor, might as well open it up. Bent the metal to allow the back plate(brush end where wires go in), to be removed. The brushes where fine but the commutator wore a little strangely. But there was brush material(carbon) between the commutator contacts. Cleaned the carbon out and smoothed the commutator some. Reassembly was a little tricky trying to hold the brushes in while getting the armature inserted. After reassembly, the bench power supply show a consistent current draw, around .3A. Reinstalled latch motor and the lid worked fine. Theory: the lid motor current is monitored by the PCB and if it is too high the PCB stops powering the motor.

I even replace the motor from a working unit. Since the new motor was from a locked machine. Once I installed, the unit detect it's in lock position, and I am able to press "open" to unlock the latch. The motor runs. BUT screen still show lift lid.

Nothing fix the issue. Only thing left untouched are the X10 connector and frequency coverter, which I don't believe they are related. I can read imbalance sensor reading around 670, which is normal.

I have a problem on the 5810R that shows the code ERROR 6 00, in the instruction manual it only talks about error 6 without zeros. The error message appears right after turning on the centrifuge after showing the equipment version.

I am not sure if they are refering to the wall outlet or the voltage coming out of the device's power supply. Since it's an operator's manual, I would say it's fhe former. Trying changing the outlet and/or performing an electrical safety test and see how that does.

The thermal sensor is a thermal fuse (temperature dependent fuse), you can still do a test by putting a jumper wire (error 6 00 disappears). You can replace it with any type in the 130 to 160C range. Note that the sensor is located between the stator coils. To replace it, care must be taken not to damage the insulating varnish of the magnetic wire of the stator coils.

The Eppendorf Centrifuge 5810/5810 R offers you the most efficient solution for your medium to high-throughput applications. The model 5810 has great versatility with a capacity for both tubes and plates. It also sports a very compact footprint for a centrifuge of its size. With the current Eppendorf rotor generation the capacity of Centrifuge 5810/5810 R increases to max. 4 x 750 mL (or max. 28 x 50 mL/56 x 15 mL). The Model 5810 is currently one of the most compact 3 liter capacity centrifuges on the market.

These compact, low-profile centrifuges are ideal for research, biotechnology, pharmaceutical, and clinical chemistry laboratories. Eppendorf Multipurpose Centrifuges feature powerful, maintenance-free motors and accommodate a variety of rotors for unparalleled application versatility. Each is three centrifuges in one: a high capacity general purpose centrifuge for cell harvesting; a high-speed centrifuge for separating cell lysates; and a micro centrifuge for DNA precipitations.

Interchangeable swing-bucket and high speed fixed-angle rotors are available to spin a variety of vessels and plates. Automatic rotor recognition senses rotor type to set maximum allowable speed. Centrifuges feature adjustable speed "Short-spin" and ten acceleration and braking rates for sensitive samples. Time, temperature (on refrigerated models), speed, and radius values can be quickly entered. User-defined programs allow quick parameter selection and ensure reproducibility. Parameters may be modified during a run. Refrigerated models feature a fast cool function to pre-cool chamber in as little as 15 minutes; standby refrigeration keeps rotor at set temperature while lid is closed; and maintains 4C at maximum speed. Non-refrigerated units are ventilated and can be used in a cold room.

For lower capacity needs in one compact unit, Model 5804 and refrigerated Model 5804 R spin volumes from 0.2mL to 4 x 100mL at low-to-high speeds for a wide range of applications. These centrifuges can accommodate capacities of up to 16 x 15mL conical (Falcon) or 30 microcentrifuge tubes per run.

Model 5810 and refrigerated Model 5810 R offer maximum application versatility and popular tube capacity, accommodating up to 4 x 400mL tubes or 16 microplates. These compact, benchtop centrifuges achieve remarkable throughput of up to 48 x 15mL or 20 x 50mL conical (Falcon) tubes.

Swing-bucket rotor A-2-DWP holds 4 deepwell plates. Commercial nucleic acid purification kits up to a maximum height of 89mm can be used. Different combinations of stacked plates can be centrifuged. Simultaneous processing of up to 192 samples. Rotor and buckets are autoclavable (121C, 20 min). Upgrade to swing-bucket rotor A-4-62 with 4 MTP buckets. For up to 16 microplates, 12 culture plates or 4 deepwell plates.

High capacity rotor with 4 x 100mL rectangular buckets. Flexible adapters for a wide range of tubes and caps for aerosol-tight centrifugation. Rotor, buckets, caps, and adapters are autoclavable (20 min, 121C). Also available with four buckets for conical 50mL tubes.

Horizontal centrifugation at high relative centrifugal forceIdeal for low sample quantities. Pellet formation at tube bottom. At max. speed, a temperature of 4C is maintained in Models 5804 R and 5810 R.

All-in-one rotor for 4 x 250mL rectangular buckets and 4 MTP buckets. Flexible adapters for a wide range of tubes. Rotor, buckets, rectangular buckets, caps and adapters are autoclavable (121C, 20 min). Caps for aerosol-tight centrifugation.

Swing-bucket Rotor A-4-81 can be upgraded with four MTP/Flex buckets to the MTP Rotor A-4-81-MTP/Flex. Accommodates up to 16 microplates, 12 culture plates or 4 deepwell plates. Flex buckets expand the functional range.

4 x 400mL rectangular buckets for high capacity. Ideal for medical and biotechnology laboratories; flexible adapters enable high sample throughput. Caps for aerosol-tight centrifugation. Rotor, buckets, caps and adapters are autoclavable (121C, 20 min).

We are currently working diligently to update our website pricing information for the New Year. If you place an order, you will be acknowledged with any corrected pricing. If you'd like the most current information sooner, please don't hesitate to drop us an email or give us a call and we'd be happy to assist. Thank you for your patience while we are updating.

The Eppendorf 5810 Multipurpose Centrifuge is designed for a variety of rotors to achieve an assortment of applications including cell harvesting, separating cell lysates, and microvolume capability for DNA precipitations. Featuring a powerful, maintenance-free motor, the 5810 can spin up to 48 x 15mL conical tubes or up to 30 microtubes per run.

The 5810, with its renowned quality and reliability, offers you the most cost-effective solution for medium to high-throughput applications requiring speeds of up to 20,913 x g (14,000 rpm). This benchtop centrifuge has been designed to fit into every lab and make routine work more comfortable thanks to its quiet operation, soft-touch lid closure and low access height for easy loading and unloading.

Experience true versatility with a broad selection of rotors and adapters (sold separately) that facilitate mixed loading of tubes, bottles and plates. A new generation of rotors increases the capacity of Centrifuge 5810/5810 R to a maximum of 4 x 750 mL (or 28 x 50 mL / 56 x 15 mL). The swing-bucket rotor and adapters accommodate tubes and bottles from 0.2 mL to 750 mL, and the fixed-angle rotor 0.2 mL to 85 mL tubes. The plate rotor is ready for you to carry out centrifugation of all types of multiwell plates, such as PCR, cell culture, or deep-well plates.

Eppendorf Centrifuge 5810 and 5810 R feature powerful and maintenance-free motors, while also accommodating a variety of rotors to meet your application needs. They are three centrifuges in one: a high-capacity, general-purpose centrifuge for cell harvesting; a high-speed centrifuge for separating cell lysates; and a microcentrifuge for DNA precipitations.

The Eppendorf Centrifuge 5810, is a benchtop centrifuge that has been designed to make routine lab work more comfortable due to its quiet operation, soft-touch lid closure and low access height for easy loading. The centrifuge offers high quality and reliable operation, and is cost-effective for medium to high-throughput applications reaching speeds of up to 14,000 rpm.

Eppendorf centrifuges 5810 and 5810 R with their renowned quality and reliability offer you the most cost efficient solutions for your medium to high-throughput applications now and in the future. Whether your applications require spinning many tubes at a time or centrifugation of larger volume vessels at high-speed, these multipurpose centrifuges with their variety of rotors and adapters cover virtually any application in tubes, bottles, flasks and microplates. They are literally three centrifuges in one: a high-capacity centrifuge for cell culture and clinical applications; a high-speed centrifuge for separating cell lysates; and a microcentrifuge for nucleic acid purification.

If space is a limited resource in your lab, Eppendorf's rolling cabinet can give you the freedom and flexibility to use your Centrifuge 5804/ 5804 R or 5810/ 5810 R wherever you need it. Use the rolling cabinet if there isn't enough space on the regular lab bench or to transport and use the centrifuge in other labs. The included drawer provides extra storage space for your rotors and adapters

3a8082e126