Re: Particle Accelerator Pdf Free Download
Hanry Moreno
Large accelerators are used for fundamental research in particle physics. The largest accelerator currently active is the Large Hadron Collider (LHC) near Geneva, Switzerland, operated by CERN. It is a collider accelerator, which can accelerate two beams of protons to an energy of 6.5 TeV and cause them to collide head-on, creating center-of-mass energies of 13 TeV. Other powerful accelerators are, RHIC at Brookhaven National Laboratory in New York and, formerly, the Tevatron at Fermilab, Batavia, Illinois. Accelerators are also used as synchrotron light sources for the study of condensed matter physics. Smaller particle accelerators are used in a wide variety of applications, including particle therapy for oncological purposes, radioisotope production for medical diagnostics, ion implanters for the manufacture of semiconductors, and accelerator mass spectrometers for measurements of rare isotopes such as radiocarbon. There are currently more than 30,000 accelerators in operation around the world.[3][4]
Rolf Widerøe, Gustav Ising, Leó Szilárd, Max Steenbeck, and Ernest Lawrence are considered pioneers of this field, having conceived and built the first operational linear particle accelerator,[6] the betatron, and the cyclotron.
Because the target of the particle beams of early accelerators was usually the atoms of a piece of matter, with the goal being to create collisions with their nuclei in order to investigate nuclear structure, accelerators were commonly referred to as atom smashers in the 20th century.[7] The term persists despite the fact that many modern accelerators create collisions between two subatomic particles, rather than a particle and an atomic nucleus.[8][9][10]
Beams of high-energy particles are useful for fundamental and applied research in the sciences, and also in many technical and industrial fields unrelated to fundamental research.[11] It has been estimated that there are approximately 30,000 accelerators worldwide. Of these, only about 1% are research machines with energies above 1 GeV, while about 44% are for radiotherapy, 41% for ion implantation, 9% for industrial processing and research, and 4% for biomedical and other low-energy research.[12]
For the most basic inquiries into the dynamics and structure of matter, space, and time, physicists seek the simplest kinds of interactions at the highest possible energies. These typically entail particle energies of many GeV, and interactions of the simplest kinds of particles: leptons (e.g. electrons and positrons) and quarks for the matter, or photons and gluons for the field quanta. Since isolated quarks are experimentally unavailable due to color confinement, the simplest available experiments involve the interactions of, first, leptons with each other, and second, of leptons with nucleons, which are composed of quarks and gluons. To study the collisions of quarks with each other, scientists resort to collisions of nucleons, which at high energy may be usefully considered as essentially 2-body interactions of the quarks and gluons of which they are composed. This elementary particle physicists tend to use machines creating beams of electrons, positrons, protons, and antiprotons, interacting with each other or with the simplest nuclei (e.g., hydrogen or deuterium) at the highest possible energies, generally hundreds of GeV or more.
Particle accelerators can also produce proton beams, which can produce proton-rich medical or research isotopes as opposed to the neutron-rich ones made in fission reactors; however, recent work has shown how to make 99Mo, usually made in reactors, by accelerating isotopes of hydrogen,[14] although this method still requires a reactor to produce tritium. An example of this type of machine is LANSCE at Los Alamos.
Everyday examples of particle accelerators are cathode ray tubes found in television sets and X-ray generators. These low-energy accelerators use a single pair of electrodes with a DC voltage of a few thousand volts between them. In an X-ray generator, the target itself is one of the electrodes. A low-energy particle accelerator called an ion implanter is used in the manufacture of integrated circuits.
DC accelerator types capable of accelerating particles to speeds sufficient to cause nuclear reactions are Cockcroft-Walton generators or voltage multipliers, which convert AC to high voltage DC, or Van de Graaff generators that use static electricity carried by belts.
Historically, the first accelerators used simple technology of a single static high voltage to accelerate charged particles. The charged particle was accelerated through an evacuated tube with an electrode at either end, with the static potential across it. Since the particle passed only once through the potential difference, the output energy was limited to the accelerating voltage of the machine. While this method is still extremely popular today, with the electrostatic accelerators greatly out-numbering any other type, they are more suited to lower energy studies owing to the practical voltage limit of about 1 MV for air insulated machines, or 30 MV when the accelerator is operated in a tank of pressurized gas with high dielectric strength, such as sulfur hexafluoride. In a tandem accelerator the potential is used twice to accelerate the particles, by reversing the charge of the particles while they are inside the terminal. This is possible with the acceleration of atomic nuclei by using anions (negatively charged ions), and then passing the beam through a thin foil to strip electrons off the anions inside the high voltage terminal, converting them to cations (positively charged ions), which are accelerated again as they leave the terminal.
The two main types of electrostatic accelerator are the Cockcroft-Walton accelerator, which uses a diode-capacitor voltage multiplier to produce high voltage, and the Van de Graaff accelerator, which uses a moving fabric belt to carry charge to the high voltage electrode. Although electrostatic accelerators accelerate particles along a straight line, the term linear accelerator is more often used for accelerators that employ oscillating rather than static electric fields.
Due to the high voltage ceiling imposed by electrical discharge, in order to accelerate particles to higher energies, techniques involving dynamic fields rather than static fields are used. Electrodynamic acceleration can arise from either of two mechanisms: non-resonant magnetic induction, or resonant circuits or cavities excited by oscillating radio frequency (RF) fields.[19] Electrodynamic accelerators can be linear, with particles accelerating in a straight line, or circular, using magnetic fields to bend particles in a roughly circular orbit.
Magnetic induction accelerators accelerate particles by induction from an increasing magnetic field, as if the particles were the secondary winding in a transformer. The increasing magnetic field creates a circulating electric field which can be configured to accelerate the particles. Induction accelerators can be either linear or circular.
Linear induction accelerators utilize ferrite-loaded, non-resonant induction cavities. Each cavity can be thought of as two large washer-shaped disks connected by an outer cylindrical tube. Between the disks is a ferrite toroid. A voltage pulse applied between the two disks causes an increasing magnetic field which inductively couples power into the charged particle beam.[20]
The linear induction accelerator was invented by Christofilos in the 1960s.[21] Linear induction accelerators are capable of accelerating very high beam currents (>1000 A) in a single short pulse. They have been used to generate X-rays for flash radiography (e.g. DARHT at LANL), and have been considered as particle injectors for magnetic confinement fusion and as drivers for free electron lasers.
The Betatron is a circular magnetic induction accelerator, invented by Donald Kerst in 1940 for accelerating electrons. The concept originates ultimately from Norwegian-German scientist Rolf Widerøe.[22][23] These machines, like synchrotrons, use a donut-shaped ring magnet (see below) with a cyclically increasing B field, but accelerate the particles by induction from the increasing magnetic field, as if they were the secondary winding in a transformer, due to the changing magnetic flux through the orbit.[24][25]
Achieving constant orbital radius while supplying the proper accelerating electric field requires that the magnetic flux linking the orbit be somewhat independent of the magnetic field on the orbit, bending the particles into a constant radius curve. These machines have in practice been limited by the large radiative losses suffered by the electrons moving at nearly the speed of light in a relatively small radius orbit.
In a linear particle accelerator (linac), particles are accelerated in a straight line with a target of interest at one end. They are often used to provide an initial low-energy kick to particles before they are injected into circular accelerators. The longest linac in the world is the Stanford Linear Accelerator, SLAC, which is 3 km (1.9 mi) long. SLAC was originally an electron-positron collider but is now a X-ray Free-electron laser.
Linear high-energy accelerators use a linear array of plates (or drift tubes) to which an alternating high-energy field is applied. As the particles approach a plate they are accelerated towards it by an opposite polarity charge applied to the plate. As they pass through a hole in the plate, the polarity is switched so that the plate now repels them and they are now accelerated by it towards the next plate. Normally a stream of "bunches" of particles are accelerated, so a carefully controlled AC voltage is applied to each plate to continuously repeat this process for each bunch.
As the particles approach the speed of light the switching rate of the electric fields becomes so high that they operate at radio frequencies, and so microwave cavities are used in higher energy machines instead of simple plates.
aa06259810