Ex2300 Firmware Download

0 views

Skip to first unread message

Celedonio Miranda

unread,

Aug 3, 2024, 4:27:10 PM8/3/24

to fifpvildiaprac

We have the video below that goes through the entire process, including how to source the firmware. Below that video are all of the steps and commands so you can copy paste into your Putty Serial Connection:

Is this command rate limit the traffic passing through switch port.srr-queue bandwitdh limit 90srr-queue bandwitdh limit enter bandwidth limit for interface as percentage. If I want to pass 9 mbps traffic through a switch port what command i ...

Guys, I didn't see any configuration problems with the LACP, the SFP or the link/fiber.But I have a topology with a LACP between 9500 x 9400, and I use 4 10G-SR interfaces.One of these interfaces is passing TX input traffic, but not RX output.I re...

Hi,I've been playing around with spanning-tree BPDUguard for a topology that has 3 switches connected on both GNS3 and PacketTracer, and both depicts the same:Topology:SW1---SW2---SW3Config:The switchport status for the SW2's interface connected to S...

Hello, PLease consider above topology, it has a Router, IE-4010 switch and it is performing L2NAT. All the PC connected to it are a part of Same VLAN-20 and PC - A-B-C are translated to some IP in the screenshot. PC D has the IP in the same subnet ...

Hi I'm a student doing an assignment rn and I think I did most of the steps right but I can't ping PC B from PC A and I cant ping PC A from B. It keeps saying destination host unreachable. Here is my file can someone please help me out and thank you ...

hello I goofed and uploaded a new image to my Cisco 3750.I deleted the prior image and set the boot flash statement and then used the command boot system flash: old image/new image This caused me to enter into switch: mode I have tried various recove...

HelloI just got a second hand Catalyst 6800IA-48FPD switch and i wanted to know the following:1-What is the latest compatible stable firmware update for this specific switch model i could apply? Either I couldn't find it or the cisco website doesn't ...

Hello everyone, could you help me with commands to determine if a Cisco IOS XE router has any password expiration controls configured. I have tried several suggested commands and I cannot determine if there is any line with which I can support that t...

HiI ran into some issues with a pair of 6880s booting. I racked up 2 c6880-X-LE switches and done the following: powered on both switches copied latest ios c6880x-ipservicesk9-mz.SPA.152-1.SY6.bin to both switches (verified md5 of ios before copyi...

I'm using Windows 10 and Packet Tracer (PT) version 8.0 in 64 bit. The router 4331 in PT shown that it has 3 gigaethernet ports. The csreen capture is as follows.However, there are only 2 gigoethernet ports can be used while cabling and the screen ca...

Hi thereI need to upgrade ninety-six switches in person My colleague downloaded the latest iOS. The plan is to complete it over the weekend. I think the iOS iscompressed.currently the switches has 16.09.04.SPA.Directory of flash:/7762 -rw- 19858044 ...

Hi i am new to python and currently learning the basic of netmiko . I built 3 scripts as below;device_1.py : contain device list , i do not input username/pw in the script for security purposemy_tool.py : prompt username/PWconfig.py : main bodyI...

I have a managed Catalyst 1000 8T 1Gb switch at the edge of my network. It's fine for how it is being used. I want to link it to a managed 16T 2.5Gb switch which will be the new core of my networking. It's fine that the link between the two will have...