[hylafax-users] Failure to train remote modem at 2400 bps or minimum speed
Walid Aweiwi
I succeeded to send the same destination via normal fax from HP.
using iaxModems
Mar 24 18:05:47.03: [27690]: SESSION BEGIN 000036082 2973021
Mar 24 18:05:47.03: [27690]: HylaFAX (tm) Version 5.2.5
Mar 24 18:05:47.03: [27690]: SEND FAX: JOB 19240 DEST 2973021 COMMID
000036082 DEVICE '/dev/ttyIAX801' FROM 'info <in...@i-net.ps>' U
SER inet
Mar 24 18:05:47.03: [27690]: STATE CHANGE: RUNNING -> SENDING
Mar 24 18:05:47.03: [27690]: <-- [12:AT+FCLASS=1\r]
Mar 24 18:05:47.03: [27690]: --> [2:OK]
Mar 24 18:05:47.03: [27690]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled
Mar 24 18:05:47.04: [27690]: DIAL 2973021
Mar 24 18:05:47.04: [27690]: <-- [12:ATDT2973021\r]
Mar 24 18:06:02.71: [27690]: --> [7:CONNECT]
Mar 24 18:06:04.33: [27690]: --> HDLC<25:FF C0 02 04 04 04 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04 04 A4 F3>
Mar 24 18:06:04.33: [27690]: --> [2:OK]
Mar 24 18:06:04.33: [27690]: REMOTE CSI ""
Mar 24 18:06:04.33: [27690]: <-- [9:AT+FRH=3\r]
Mar 24 18:06:04.77: [27690]: --> [7:CONNECT]
Mar 24 18:06:04.77: [27690]: --> HDLC<9:FF C8 01 00 72 9F 00 0C DE>
Mar 24 18:06:04.87: [27690]: --> [2:OK]
Mar 24 18:06:04.87: [27690]: REMOTE best rate 9600 bit/s
Mar 24 18:06:04.87: [27690]: REMOTE max B4 page width (255 mm)
Mar 24 18:06:04.87: [27690]: REMOTE max unlimited page length
Mar 24 18:06:04.87: [27690]: REMOTE best vres 7.7 line/mm
Mar 24 18:06:04.87: [27690]: REMOTE format support: MH
Mar 24 18:06:04.87: [27690]: REMOTE best 0 ms/scanline
Mar 24 18:06:04.87: [27690]: USE 9600 bit/s
Mar 24 18:06:04.87: [27690]: SEND file "docq/doc6998.ps;00"
Mar 24 18:06:04.87: [27690]: USE A4 page width (215 mm)
Mar 24 18:06:04.87: [27690]: USE unlimited page length
Mar 24 18:06:04.87: [27690]: USE 3.85 line/mm
Mar 24 18:06:04.87: [27690]: USE 1-D MH
Mar 24 18:06:04.87: [27690]: USE 0 ms/scanline
Mar 24 18:06:04.87: [27690]: SEND training at v.29 9600 bit/s
Mar 24 18:06:04.87: [27690]: <-- [9:AT+FRS=7\r]
Mar 24 18:06:04.93: [27690]: --> [2:OK]
Mar 24 18:06:04.93: [27690]: <-- [9:AT+FTH=3\r]
Mar 24 18:06:04.95: [27690]: --> [7:CONNECT]
Mar 24 18:06:04.95: [27690]: <-- HDLC<23:FF C0 C2 74 26 2E 36 04 CE 76 F6
96 2E AE 36 F6 CA 04 2A A2 72 96 04>
Mar 24 18:06:04.95: [27690]: <-- data [23]
Mar 24 18:06:04.95: [27690]: <-- data [2]
Mar 24 18:06:06.49: [27690]: --> [7:CONNECT]
Mar 24 18:06:06.49: [27690]: <-- HDLC<6:FF C8 C1 00 60 1E>
Mar 24 18:06:06.49: [27690]: <-- data [6]
Mar 24 18:06:06.49: [27690]: <-- data [2]
Mar 24 18:06:06.85: [27690]: --> [2:OK]
Mar 24 18:06:06.85: [27690]: <-- [9:AT+FTS=7\r]
Mar 24 18:06:06.93: [27690]: --> [2:OK]
Mar 24 18:06:06.93: [27690]: MODEM set XON/XOFF/FLUSH: input interpreted,
output disabled
Mar 24 18:06:06.93: [27690]: <-- [10:AT+FTM=96\r]
Mar 24 18:06:06.93: [27690]: --> [7:CONNECT]
Mar 24 18:06:06.93: [27690]: DELAY 4000 ms
Mar 24 18:06:10.93: [27690]: <-- data [1024]
Mar 24 18:06:10.93: [27690]: <-- data [776]
Mar 24 18:06:10.93: [27690]: <-- data [2]
Mar 24 18:06:12.49: [27690]: --> [2:OK]
Mar 24 18:06:12.49: [27690]: MODEM set XON/XOFF/DRAIN: input ignored,
output disabled
Mar 24 18:06:12.49: [27690]: <-- [9:AT+FRH=3\r]
Mar 24 18:06:12.83: [27690]: --> [7:CONNECT]
Mar 24 18:06:13.89: [27690]: --> HDLC<5:FF C8 22 67 DD>
Mar 24 18:06:13.99: [27690]: --> [2:OK]
Mar 24 18:06:13.99: [27690]: SEND training at v.29 7200 bit/s
Mar 24 18:06:13.99: [27690]: <-- [9:AT+FRS=7\r]
Mar 24 18:06:14.05: [27690]: --> [2:OK]
Mar 24 18:06:14.05: [27690]: <-- [9:AT+FTH=3\r]
Mar 24 18:06:14.07: [27690]: --> [7:CONNECT]
Mar 24 18:06:14.07: [27690]: <-- HDLC<23:FF C0 C2 74 26 2E 36 04 CE 76 F6
96 2E AE 36 F6 CA 04 2A A2 72 96 04>
Mar 24 18:06:14.07: [27690]: <-- data [23]
Mar 24 18:06:14.07: [27690]: <-- data [2]
Mar 24 18:06:15.61: [27690]: --> [7:CONNECT]
Mar 24 18:06:15.61: [27690]: <-- HDLC<6:FF C8 C1 00 70 1E>
Mar 24 18:06:15.61: [27690]: <-- data [6]
Mar 24 18:06:15.61: [27690]: <-- data [2]
Mar 24 18:06:15.97: [27690]: --> [2:OK]
Mar 24 18:06:15.97: [27690]: <-- [9:AT+FTS=7\r]
Mar 24 18:06:16.05: [27690]: --> [2:OK]
Mar 24 18:06:16.05: [27690]: MODEM set XON/XOFF/FLUSH: input interpreted,
output disabled
Mar 24 18:06:16.05: [27690]: <-- [10:AT+FTM=72\r]
Mar 24 18:06:16.05: [27690]: --> [7:CONNECT]
Mar 24 18:06:16.05: [27690]: DELAY 4000 ms
Mar 24 18:06:20.05: [27690]: <-- data [1024]
Mar 24 18:06:20.05: [27690]: <-- data [326]
Mar 24 18:06:20.05: [27690]: <-- data [2]
Mar 24 18:06:21.59: [27690]: --> [2:OK]
Mar 24 18:06:21.59: [27690]: MODEM set XON/XOFF/DRAIN: input ignored,
output disabled
Mar 24 18:06:21.59: [27690]: <-- [9:AT+FRH=3\r]
Mar 24 18:06:21.89: [27690]: --> [7:CONNECT]
Mar 24 18:06:22.99: [27690]: --> HDLC<5:FF C8 22 67 DD>
Mar 24 18:06:23.09: [27690]: --> [2:OK]
Mar 24 18:06:23.09: [27690]: SEND training at v.27ter 4800 bit/s
Mar 24 18:06:23.09: [27690]: <-- [9:AT+FRS=7\r]
Mar 24 18:06:23.17: [27690]: --> [2:OK]
Mar 24 18:06:23.17: [27690]: <-- [9:AT+FTH=3\r]
Mar 24 18:06:23.19: [27690]: --> [7:CONNECT]
Mar 24 18:06:23.19: [27690]: <-- HDLC<23:FF C0 C2 74 26 2E 36 04 CE 76 F6
96 2E AE 36 F6 CA 04 2A A2 72 96 04>
Mar 24 18:06:23.19: [27690]: <-- data [23]
Mar 24 18:06:23.19: [27690]: <-- data [2]
Mar 24 18:06:24.73: [27690]: --> [7:CONNECT]
Mar 24 18:06:24.73: [27690]: <-- HDLC<6:FF C8 C1 00 50 1E>
Mar 24 18:06:24.73: [27690]: <-- data [6]
Mar 24 18:06:24.73: [27690]: <-- data [2]
Mar 24 18:06:25.09: [27690]: --> [2:OK]
Mar 24 18:06:25.09: [27690]: <-- [9:AT+FTS=7\r]
Mar 24 18:06:25.17: [27690]: --> [2:OK]
Mar 24 18:06:25.17: [27690]: MODEM set XON/XOFF/FLUSH: input interpreted,
output disabled
Mar 24 18:06:25.17: [27690]: <-- [10:AT+FTM=48\r]
Mar 24 18:06:25.17: [27690]: --> [7:CONNECT]
Mar 24 18:06:25.17: [27690]: DELAY 4000 ms
Mar 24 18:06:29.17: [27690]: <-- data [900]
Mar 24 18:06:29.17: [27690]: <-- data [2]
Mar 24 18:06:30.75: [27690]: --> [2:OK]
Mar 24 18:06:30.75: [27690]: MODEM set XON/XOFF/DRAIN: input ignored,
output disabled
Mar 24 18:06:30.75: [27690]: <-- [9:AT+FRH=3\r]
Mar 24 18:06:33.85: [27690]: --> [0:]
Mar 24 18:06:33.85: [27690]: MODEM <Empty line>
Mar 24 18:06:33.85: [27690]: MODEM TIMEOUT: waiting for v.21 carrier
Mar 24 18:06:33.85: [27690]: <-- data [1]
Mar 24 18:06:33.87: [27690]: --> [2:OK]
Mar 24 18:06:33.87: [27690]: <-- [9:AT+FRS=7\r]
Mar 24 18:06:33.87: [27690]: --> [2:OK]
Mar 24 18:06:33.87: [27690]: SEND training at v.27ter fallback mode 2400
bit/s
Mar 24 18:06:33.87: [27690]: <-- [9:AT+FTH=3\r]
Mar 24 18:06:33.89: [27690]: --> [7:CONNECT]
Mar 24 18:06:33.89: [27690]: <-- HDLC<23:FF C0 C2 74 26 2E 36 04 CE 76 F6
96 2E AE 36 F6 CA 04 2A A2 72 96 04>
Mar 24 18:06:33.89: [27690]: <-- data [23]
Mar 24 18:06:33.89: [27690]: <-- data [2]
Mar 24 18:06:35.43: [27690]: --> [7:CONNECT]
Mar 24 18:06:35.43: [27690]: <-- HDLC<6:FF C8 C1 00 40 1E>
Mar 24 18:06:35.43: [27690]: <-- data [6]
Mar 24 18:06:35.43: [27690]: <-- data [2]
Mar 24 18:06:35.79: [27690]: --> [2:OK]
Mar 24 18:06:35.79: [27690]: <-- [9:AT+FTS=7\r]
Mar 24 18:06:35.87: [27690]: --> [2:OK]
Mar 24 18:06:35.87: [27690]: MODEM set XON/XOFF/FLUSH: input interpreted,
output disabled
Mar 24 18:06:35.87: [27690]: <-- [10:AT+FTM=24\r]
Mar 24 18:06:35.89: [27690]: --> [7:CONNECT]
Mar 24 18:06:35.89: [27690]: DELAY 4000 ms
Mar 24 18:06:39.89: [27690]: <-- data [450]
Mar 24 18:06:39.89: [27690]: <-- data [2]
Mar 24 18:06:41.45: [27690]: --> [2:OK]
Mar 24 18:06:41.45: [27690]: MODEM set XON/XOFF/DRAIN: input ignored,
output disabled
Mar 24 18:06:41.45: [27690]: <-- [9:AT+FRH=3\r]
Mar 24 18:06:44.55: [27690]: --> [0:]
Mar 24 18:06:44.55: [27690]: MODEM <Empty line>
Mar 24 18:06:44.55: [27690]: MODEM TIMEOUT: waiting for v.21 carrier
Mar 24 18:06:44.55: [27690]: <-- data [1]
Mar 24 18:06:44.55: [27690]: --> [2:OK]
Mar 24 18:06:44.55: [27690]: <-- [9:AT+FRS=7\r]
Mar 24 18:06:44.57: [27690]: --> [2:OK]
Mar 24 18:06:44.57: [27690]: TRAINING failed
Mar 24 18:06:44.57: [27690]: SEND: Failure to train remote modem at 2400
bps or minimum speed {E137}; Giving up after 3 attempts to
send same page "docq/doc6998.ps;00", dirnum 0
Mar 24 18:06:44.57: [27690]: <-- [9:AT+FTH=3\r]
Mar 24 18:06:44.59: [27690]: --> [7:CONNECT]
Mar 24 18:06:44.59: [27690]: <-- HDLC<3:FF C8 DF>
Mar 24 18:06:44.59: [27690]: <-- data [3]
Mar 24 18:06:44.59: [27690]: <-- data [2]
Mar 24 18:06:45.67: [27690]: --> [2:OK]
Mar 24 18:06:45.67: [27690]: MODEM input buffering enabled
Mar 24 18:06:46.67: [27690]: <-- [5:ATH0\r]
Mar 24 18:06:46.80: [27690]: --> [2:OK]
Mar 24 18:06:46.80: [27690]: MODEM set DTR OFF
Mar 24 18:06:46.80: [27690]: MODEM set baud rate: 0 baud (flow control
unchanged)
Mar 24 18:06:46.80: [27690]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Mar 24 18:06:46.80: [27690]: SESSION END
--
Best Regards
Walid Aweiwi
Technical Manager
iNET Solutions Ltd.
Tel/Fax: +970 2 2989160
Mobile: +970 597 989303
E-mail: wa...@i-net.ps
Web Sites:
http://www.i-net.ps
http://www.inetfax.ps
--
This message has been scanned for viruses and
dangerous content by "iNET Solutions" security systems, and is
believed to be clean.
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-us...@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sa...@ifax.com.*
Walid Aweiwi
# $Id: iaxmodem,v 1.7 2007/11/06 18:44:20 faxguy Exp $
#
# prototype config for the IAXmodem softmodem which uses
# the spandsp soft-DSP library
#
#
CountryCode: 970
AreaCode: 2
FAXNumber:
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 0xFFF
RecvFileMode: 0644
LogFileMode: 0644
DeviceMode: 0644
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier:
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 250
NotifyCmd: bin/notify.php
#
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use this to supply a hint
#
# *** Caller-ID settings ***
#
# Enabling this will use the hfaxd-protocol to set Caller*ID
#
#ModemSetOriginCmd: "AT+VSID=\"%s\",\"%d\""
#
# If "glare" during initialization becomes a problem then take
# the modem off-hook during initialization, and then place it
# back on-hook when done.
#
#ModemResetCmds: "ATH1\nAT+VCID=1" # enables CallID display
#ModemReadyCmds: ATH0
#
# You'll likely want Caller*ID display (also displays DID) enabled.
#
ModemResetCmds: AT+VCID=1 # enables CallID display
#
# If you are "missing" Caller*ID data on some calls (but not all)
# and if you do not have adequate glare protection you may want to
# not answer based on RINGs, but rather enable the CallIDAnswerLength
# for NDID, disable AT+VCID=1 and do this:
#
#RingsBeforeAnswer: 0
#ModemRingResponse: AT+VRID=1
# The pty apparently does not support changing parity.
PagerTTYParity: none
Class1AdaptRecvCmd: AT+FAR=1
Class1TMConnectDelay: 400 # counteract quick CONNECT response
#
# Older iaxmodem versions didn't support V.17 very well. It can be
# disabled in this fashion:
#
#Class1RMQueryCmd: "!24,48,72,96" # V.17 fast-train recv doesn't
work well
#Class1TMQueryCmd: "!24,48,72,96" # V.17 fast-train recv doesn't
work well
CallIDPattern: "NMBR="
CallIDPattern: "NAME="
CallIDPattern: "ANID="
CallIDPattern: "NDID="
#CallIDAnswerLength: 4
# Uncomment these if you really want them, but you probably don't.
#CallIDPattern: "DATE="
#CallIDPattern: "TIME="
#20060302 JDG - Fix for broken libtiff JBIG support in tiff2pdf
Class1JBIGSupport: no
Lee Howard
> Hi see below logs:
>
> I succeeded to send the same destination via normal fax from HP.
>
> using iaxModems
>
> Mar 24 18:05:47.03: [27690]: SESSION BEGIN 000036082 2973021
> Mar 24 18:05:47.03: [27690]: HylaFAX (tm) Version 5.2.5
> Mar 24 18:05:47.03: [27690]: SEND FAX: JOB 19240 DEST 2973021 COMMID
> 000036082 DEVICE '/dev/ttyIAX801' FROM 'info <in...@i-net.ps>' U
> SER inet
It's probably an issue with your audio quality. Are you running
iaxmodem on the same host as Asterisk? Are you using DAHDI/Zap devices?
Thanks,
Lee.
Walid Aweiwi
But I'm already use it for year and half ago and I'm sending to other destinations without such error
Best Regards,
---------------------
-----Original Message-----
From: Lee Howard [mailto:fax...@howardsilvan.com]
Sent: Sunday, March 27, 2011 1:17 AM
To: Walid Aweiwi
Cc: hylafa...@hylafax.org
Subject: Re: [hylafax-users] Failure to train remote modem at 2400 bps or minimum speed
Walid Aweiwi wrote:
> Hi see below logs:
>
> I succeeded to send the same destination via normal fax from HP.
>
> using iaxModems
>
> Mar 24 18:05:47.03: [27690]: SESSION BEGIN 000036082 2973021
> Mar 24 18:05:47.03: [27690]: HylaFAX (tm) Version 5.2.5
> Mar 24 18:05:47.03: [27690]: SEND FAX: JOB 19240 DEST 2973021 COMMID
> 000036082 DEVICE '/dev/ttyIAX801' FROM 'info <in...@i-net.ps>' U
> SER inet
It's probably an issue with your audio quality. Are you running
iaxmodem on the same host as Asterisk? Are you using DAHDI/Zap devices?
Thanks,
Lee.
--
This message has been scanned for viruses and
dangerous content by "iNET Solutions" security systems, and is
believed to be clean.
--
This message has been scanned for viruses and
dangerous content by "iNET Solutions" security systems, and is
believed to be clean.
Walid Aweiwi
See logs below
Mar 27 10:38:56.78: [31429]: SESSION BEGIN 000002637 97222973021
Mar 27 10:38:56.78: [31429]: HylaFAX (tm) Version 6.0.4
Mar 27 10:38:56.78: [31429]: SEND FAX: JOB 653 DEST 2973021 COMMID 000002637 DEVICE '/dev/ttyIAX1' FROM 'walid <wa...@i-net.ps>' USE
R admin
Mar 27 10:38:56.78: [31429]: STATE CHANGE: RUNNING -> SENDING
Mar 27 10:38:56.78: [31429]: <-- [12:AT+FCLASS=1\r]
Mar 27 10:38:56.78: [31429]: --> [2:OK]
Mar 27 10:38:56.78: [31429]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Mar 27 10:38:56.78: [31429]: DIAL 2973021
Mar 27 10:38:56.78: [31429]: <-- [12:ATDT2973021\r]
Mar 27 10:39:13.17: [31429]: --> [7:CONNECT]
Mar 27 10:39:14.81: [31429]: --> HDLC<25:FF C0 02 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 A4 F3>
Mar 27 10:39:14.81: [31429]: --> [2:OK]
Mar 27 10:39:14.81: [31429]: REMOTE CSI ""
Mar 27 10:39:14.81: [31429]: <-- [9:AT+FRH=3\r]
Mar 27 10:39:15.23: [31429]: --> [7:CONNECT]
Mar 27 10:39:15.23: [31429]: --> HDLC<9:FF C8 01 00 72 9F 00 0C DE>
Mar 27 10:39:15.33: [31429]: --> [2:OK]
Mar 27 10:39:15.33: [31429]: REMOTE best rate 9600 bit/s
Mar 27 10:39:15.33: [31429]: REMOTE max B4 page width (255 mm)
Mar 27 10:39:15.33: [31429]: REMOTE max unlimited page length
Mar 27 10:39:15.33: [31429]: REMOTE best vres 7.7 line/mm
Mar 27 10:39:15.33: [31429]: REMOTE format support: MH
Mar 27 10:39:15.33: [31429]: REMOTE best 0 ms/scanline
Mar 27 10:39:15.33: [31429]: USE 9600 bit/s
Mar 27 10:39:15.33: [31429]: SEND file "docq/doc708.ps;c1"
Mar 27 10:39:15.33: [31429]: USE A4 page width (215 mm)
Mar 27 10:39:15.33: [31429]: USE unlimited page length
Mar 27 10:39:15.33: [31429]: USE 7.7 line/mm
Mar 27 10:39:15.33: [31429]: USE 1-D MH
Mar 27 10:39:15.33: [31429]: USE 0 ms/scanline
Mar 27 10:39:15.33: [31429]: SEND training at v.29 9600 bit/s
Mar 27 10:39:15.33: [31429]: <-- [9:AT+FRS=7\r]
Mar 27 10:39:15.39: [31429]: --> [2:OK]
Mar 27 10:39:15.39: [31429]: <-- [9:AT+FTH=3\r]
Mar 27 10:39:15.41: [31429]: --> [7:CONNECT]
Mar 27 10:39:15.41: [31429]: <-- HDLC<23:FF C0 C2 2E CE A6 2E 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>
Mar 27 10:39:15.41: [31429]: <-- data [23]
Mar 27 10:39:15.41: [31429]: <-- data [2]
Mar 27 10:39:16.95: [31429]: --> [7:CONNECT]
Mar 27 10:39:16.95: [31429]: <-- HDLC<6:FF C8 C1 00 62 1E>
Mar 27 10:39:16.95: [31429]: <-- data [6]
Mar 27 10:39:16.95: [31429]: <-- data [2]
Mar 27 10:39:17.31: [31429]: --> [2:OK]
Mar 27 10:39:17.31: [31429]: <-- [9:AT+FTS=7\r]
Mar 27 10:39:17.41: [31429]: --> [2:OK]
Mar 27 10:39:17.41: [31429]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Mar 27 10:39:17.41: [31429]: <-- [10:AT+FTM=96\r]
Mar 27 10:39:17.43: [31429]: --> [7:CONNECT]
Mar 27 10:39:17.43: [31429]: DELAY 400 ms
Mar 27 10:39:17.83: [31429]: <-- data [1024]
Mar 27 10:39:17.83: [31429]: <-- data [776]
Mar 27 10:39:17.83: [31429]: <-- data [2]
Mar 27 10:39:19.39: [31429]: --> [2:OK]
Mar 27 10:39:19.39: [31429]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Mar 27 10:39:19.39: [31429]: <-- [9:AT+FRH=3\r]
Mar 27 10:39:19.69: [31429]: --> [7:CONNECT]
Mar 27 10:39:20.79: [31429]: --> HDLC<5:FF C8 22 67 DD>
Mar 27 10:39:20.89: [31429]: --> [2:OK]
Mar 27 10:39:20.89: [31429]: SEND training at v.29 7200 bit/s
Mar 27 10:39:20.89: [31429]: <-- [9:AT+FRS=7\r]
Mar 27 10:39:20.97: [31429]: --> [2:OK]
Mar 27 10:39:20.97: [31429]: <-- [9:AT+FTH=3\r]
Mar 27 10:39:20.99: [31429]: --> [7:CONNECT]
Mar 27 10:39:20.99: [31429]: <-- HDLC<23:FF C0 C2 2E CE A6 2E 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>
Mar 27 10:39:20.99: [31429]: <-- data [23]
Mar 27 10:39:20.99: [31429]: <-- data [2]
Mar 27 10:39:22.53: [31429]: --> [7:CONNECT]
Mar 27 10:39:22.53: [31429]: <-- HDLC<6:FF C8 C1 00 72 1E>
Mar 27 10:39:22.53: [31429]: <-- data [6]
Mar 27 10:39:22.53: [31429]: <-- data [2]
Mar 27 10:39:22.89: [31429]: --> [2:OK]
Mar 27 10:39:22.89: [31429]: <-- [9:AT+FTS=7\r]
Mar 27 10:39:22.99: [31429]: --> [2:OK]
Mar 27 10:39:22.99: [31429]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Mar 27 10:39:22.99: [31429]: <-- [10:AT+FTM=72\r]
Mar 27 10:39:23.01: [31429]: --> [7:CONNECT]
Mar 27 10:39:23.01: [31429]: DELAY 400 ms
Mar 27 10:39:23.41: [31429]: <-- data [1024]
Mar 27 10:39:23.41: [31429]: <-- data [326]
Mar 27 10:39:23.41: [31429]: <-- data [2]
Mar 27 10:39:24.97: [31429]: --> [2:OK]
Mar 27 10:39:24.97: [31429]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Mar 27 10:39:24.97: [31429]: <-- [9:AT+FRH=3\r]
Mar 27 10:39:25.29: [31429]: --> [7:CONNECT]
Mar 27 10:39:26.39: [31429]: --> HDLC<5:FF C8 22 67 DD>
Mar 27 10:39:26.49: [31429]: --> [2:OK]
Mar 27 10:39:26.49: [31429]: SEND training at v.27ter 4800 bit/s
Mar 27 10:39:26.49: [31429]: <-- [9:AT+FRS=7\r]
Mar 27 10:39:26.55: [31429]: --> [2:OK]
Mar 27 10:39:26.55: [31429]: <-- [9:AT+FTH=3\r]
Mar 27 10:39:26.57: [31429]: --> [7:CONNECT]
Mar 27 10:39:26.57: [31429]: <-- HDLC<23:FF C0 C2 2E CE A6 2E 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>
Mar 27 10:39:26.57: [31429]: <-- data [23]
Mar 27 10:39:26.57: [31429]: <-- data [2]
Mar 27 10:39:28.11: [31429]: --> [7:CONNECT]
Mar 27 10:39:28.11: [31429]: <-- HDLC<6:FF C8 C1 00 52 1E>
Mar 27 10:39:28.11: [31429]: <-- data [6]
Mar 27 10:39:28.11: [31429]: <-- data [2]
Mar 27 10:39:28.47: [31429]: --> [2:OK]
Mar 27 10:39:28.47: [31429]: <-- [9:AT+FTS=7\r]
Mar 27 10:39:28.57: [31429]: --> [2:OK]
Mar 27 10:39:28.57: [31429]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Mar 27 10:39:28.57: [31429]: <-- [10:AT+FTM=48\r]
Mar 27 10:39:28.59: [31429]: --> [7:CONNECT]
Mar 27 10:39:28.59: [31429]: DELAY 400 ms
Mar 27 10:39:28.99: [31429]: <-- data [900]
Mar 27 10:39:28.99: [31429]: <-- data [2]
Mar 27 10:39:30.87: [31429]: --> [2:OK]
Mar 27 10:39:30.87: [31429]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Mar 27 10:39:30.87: [31429]: <-- [9:AT+FRH=3\r]
Mar 27 10:39:33.97: [31429]: --> [0:]
Mar 27 10:39:33.97: [31429]: MODEM <Empty line>
Mar 27 10:39:33.97: [31429]: MODEM TIMEOUT: waiting for v.21 carrier
Mar 27 10:39:33.97: [31429]: <-- data [1]
Mar 27 10:39:33.99: [31429]: --> [2:OK]
Mar 27 10:39:33.99: [31429]: <-- [9:AT+FRS=7\r]
Mar 27 10:39:34.01: [31429]: --> [2:OK]
Mar 27 10:39:34.01: [31429]: SEND training at v.27ter fallback mode 2400 bit/s
Mar 27 10:39:34.01: [31429]: <-- [9:AT+FTH=3\r]
Mar 27 10:39:34.01: [31429]: --> [7:CONNECT]
Mar 27 10:39:34.01: [31429]: <-- HDLC<23:FF C0 C2 2E CE A6 2E 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>
Mar 27 10:39:34.01: [31429]: <-- data [23]
Mar 27 10:39:34.01: [31429]: <-- data [2]
Mar 27 10:39:35.55: [31429]: --> [7:CONNECT]
Mar 27 10:39:35.55: [31429]: <-- HDLC<6:FF C8 C1 00 42 1E>
Mar 27 10:39:35.55: [31429]: <-- data [6]
Mar 27 10:39:35.55: [31429]: <-- data [2]
Mar 27 10:39:35.91: [31429]: --> [2:OK]
Mar 27 10:39:35.91: [31429]: <-- [9:AT+FTS=7\r]
Mar 27 10:39:36.01: [31429]: --> [2:OK]
Mar 27 10:39:36.01: [31429]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Mar 27 10:39:36.01: [31429]: <-- [10:AT+FTM=24\r]
Mar 27 10:39:36.03: [31429]: --> [7:CONNECT]
Mar 27 10:39:36.03: [31429]: DELAY 400 ms
Mar 27 10:39:36.43: [31429]: <-- data [450]
Mar 27 10:39:36.43: [31429]: <-- data [2]
Mar 27 10:39:38.55: [31429]: --> [2:OK]
Mar 27 10:39:38.55: [31429]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Mar 27 10:39:38.55: [31429]: <-- [9:AT+FRH=3\r]
Mar 27 10:39:41.65: [31429]: --> [0:]
Mar 27 10:39:41.65: [31429]: MODEM <Empty line>
Mar 27 10:39:41.65: [31429]: MODEM TIMEOUT: waiting for v.21 carrier
Mar 27 10:39:41.65: [31429]: <-- data [1]
Mar 27 10:39:41.67: [31429]: --> [2:OK]
Mar 27 10:39:41.67: [31429]: <-- [9:AT+FRS=7\r]
Mar 27 10:39:41.69: [31429]: --> [2:OK]
Mar 27 10:39:41.69: [31429]: TRAINING failed
Mar 27 10:39:41.69: [31429]: <-- [9:AT+FTH=3\r]
Mar 27 10:39:41.71: [31429]: --> [7:CONNECT]
Mar 27 10:39:41.71: [31429]: <-- HDLC<3:FF C8 DF>
Mar 27 10:39:41.71: [31429]: <-- data [3]
Mar 27 10:39:41.71: [31429]: <-- data [2]
Mar 27 10:39:42.79: [31429]: --> [2:OK]
Mar 27 10:39:42.79: [31429]: MODEM input buffering enabled
Mar 27 10:39:43.79: [31429]: <-- [5:ATH0\r]
Mar 27 10:39:43.91: [31429]: --> [2:OK]
Mar 27 10:39:43.91: [31429]: MODEM set DTR OFF
Mar 27 10:39:43.91: [31429]: MODEM set baud rate: 0 baud (flow control unchanged)
Mar 27 10:39:43.91: [31429]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Mar 27 10:39:43.91: [31429]: SESSION END
Best Regards,
---------------------
-----Original Message-----
From: hylafax-us...@hylafax.org [mailto:hylafax-us...@hylafax.org] On Behalf Of Lee Howard
Sent: Sunday, March 27, 2011 1:17 AM
To: Walid Aweiwi
Cc: hylafa...@hylafax.org
Thanks,
Lee.
--
This message has been scanned for viruses and
dangerous content by "iNET Solutions" security systems, and is
believed to be clean.
--
This message has been scanned for viruses and
dangerous content by "iNET Solutions" security systems, and is
believed to be clean.
Lee Howard
> Iaxmodem in the same as Asterisk and I'm using Zap driver.
>
> But I'm already use it for year and half ago and I'm sending to other destinations without such error
Then it may very-well be an issue on the receive-side at the
destination. What kind of error message are they getting over there?
The fact that the destination does not give NSF, does not support ECM,
and supports a maximum bitrate of 9600 bps is an indication of a very
poor-quality fax server (software).
Talk to the receiver, find out what kind of fax software they're using,
and work at the problem from their end.
Thanks,
Lee.
Walid Aweiwi
Also I used a regular fax machine from my side and I succeeded to send
them a test fax.
Any ideas?
> --
> This message has been scanned for viruses and
> dangerous content by "iNET Solutions" security systems, and is
> believed to be clean.
>
>
--
This message has been scanned for viruses and
dangerous content by "iNET Solutions" security systems, and is
believed to be clean.
Lee Howard
Thanks,
Lee.