Help with error messages

[James Balls]

Im trying to get DIXPRS running with KISS TNC

I have followed the install instructions at http://www.pa0esh.nl/wordpress/?wpfb_dl=9 but leaving out the sound modem part

I have edited the config.txt file for KISS but when I try to run using 

root@raspberrypi:/etc/init.d# ./dixprs start

I get the follwing messages

Starting dixprs in a screen

/usr/local/dixprs/config.txt: 49: /usr/local/dixprs/config.txt: [GENERAL]: not found

/usr/local/dixprs/config.txt: 84: /usr/local/dixprs/config.txt: Igate: not found

/usr/local/dixprs/config.txt: 105: /usr/local/dixprs/config.txt: [ISGW]: not found

/usr/local/dixprs/config.txt: 127: /usr/local/dixprs/config.txt: [WEBSERVER]: not found

/usr/local/dixprs/config.txt: 141: /usr/local/dixprs/config.txt: [RADIO]: not found

/usr/local/dixprs/config.txt: 168: /usr/local/dixprs/config.txt: 144.800: not found

root@raspberrypi:/etc/init.d# cd /usr/local/dixprs/

Any ideas please?

Jim M0CKE

 

[Antal Vincz]

Hello Jim,

My KISS TNC config (PK232).

[RADIO]

# Mandatory parameters

# Interface type

INTERFACE=KISS

# Serial port

PORT=/dev/ttyS0

# Serial port speed

SPEED=4800

# Optional parameters

# Modem speed, default is 1200

#SIGNALRATE=1200

# Enable/disable NWS WX bulletin and object gating from IS to Rf

# Disabled by default

#GATENWS=<y/n>

# Enable/disable BOM WX bulletin and object gating from IS to Rf

# Disabled by default

#GATEBOM=<y/n>

# Descripton of port; no default

DESCRIPTION=144.800MHz 1200Bd, AX.25 stack (KISS-TNC)

# Via used to send locally generated packets; default is WIDE1-1,WIDE2-2

AXVIA=wide1-1

# Digipeaters processed with WIDEn-n algorithm; default is WIDE1,WIDE2

WIDEN=wide1

# Blacklisted stations; they are not digipeated, not gated; default is NOCALL,N0CALL

BLACKLIST=nocall,n0call

# PHG string, do not mix with range; no default

PHG=3250

# Range value in miles, do not mix with PHG; no default

#RNG=<n>

# Enable/disable transmission; change it to PTTON=1 to enable trasmission; default is no

PTTON=1

# Gate locally generated frames to IS gateway; default is no

# Useful for rx-only radio ports

# Experimental, use carefully

#GATELOCAL=<y/n>

# Gate digipeated frames to IS gateway; default is no

# Experimental, use carefully

#GATEDIGI=<y/n>

# Beacon text; %v replaced with actual version string; default is %v

BCNTXT=%v (AIR)

# Enable/disable digipeater; default is enabled

#DIGIPEATER=<y/n>

# KISS TNC setup parameters 0...255; no defaults

# Use to setup TNC by DIXPRS

#TXD=<n>

#PPERSIST=<n>

#SLOTTIME=<n>

#TXTAIL=<n>

#DUPLEX=<n>

# Below these are the traffic shaping settings for gating messages

# From IS to Rf

#

# For advanced users only; do not change if you do not know how

# traffic shaping works and if you do not have good reason !!!

# Traffic shaping high treshold, default is 0.75

#TRAFFICHIGH=<fv>

# Traffic shaping low treshold, default is 0.5

#TRAFFIClow=<fv>

73' Toni

--
Azért kapta ezt az üzenetet, mert feliratkozott a Google Csoportok „dixprs” csoportjára.
Az erről a csoportról és az ahhoz kapcsolódó e-mailekről való leiratkozáshoz küldjön egy e-amailt a(z) dixprs+un...@googlegroups.com címre.
További lehetőségekért látogasson el ide: https://groups.google.com/d/optout.

[Bela Markus]

Hi Jim,

for diagnostic start dixprs manually in the directory where you have installed it.

Make sure you have the config file in the same directory.

Regards... Béla, HA5DI

--
Azért kapta ezt az üzenetet, mert feliratkozott a Google Csoportok „dixprs” csoportjára.
Az erről a csoportról és az ahhoz kapcsolódó e-mailekről való leiratkozáshoz küldjön egy e-amailt a(z) dixprs+un...@googlegroups.com címre.
További lehetőségekért látogasson el ide: https://groups.google.com/d/optout.

---

Ezt az e-mailt az Avast víruskereső szoftver átvizsgálta. www.avast.com