Icom IC-706MKIIG CAT Setup HELP!

51 views
Skip to first unread message

Felipe Guilfuchi Ramos

unread,
Oct 22, 2026, 9:24:02 PMOct 22
to DigiPi
I just finished building a new Digipi with a 5" screen, a DRA-45 interface and a Raspberry 3B+. I will be using it for HF communications and want to set it up correctly for the different programs on the Digipi. I purchased a CAT cable for my IC-706MKIIG and it is recognized
by the Digipi as well as my DRA-45.
The CAT setup settings are a bit confusing and I need help setting it up in the different programs.
Most important for me is Pat Email, Ardop and Mercury.
I also need some pointers for setting the TX audio correctly.
I have used Digipi on 2 meters with my portable radios and my TYT MD9600 and it worked very well but HF is another beast!
Any help will be greatly appreciated.
 
 

Craig

unread,
Oct 23, 2026, 12:53:14 PMOct 23
to Felipe Guilfuchi Ramos, DigiPi
Hi Felipe,

the DRA45 isn't explicitly supported by DigiPi.

It's unclear how PTT is asserted -- it uses a cm119a chip.  the ic706 should
just need a serial port adapter and you select hamlib and your rig number for
ptt?  the audio should "just work".

You might ask Masters Communications how to setup digipi with that
device, i just can't find any docs on how it works exactly.

-craig
KM6LYW
--
You received this message because you are subscribed to the Google Groups "DigiPi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to digipi+un...@googlegroups.com.
To view this discussion visit https://groups.google.com/d/msgid/digipi/26417fc8-9383-4e3d-af1b-2b668f596cabn%40googlegroups.com.

Scott Currie

unread,
Oct 23, 2026, 5:53:34 PMOct 23
to DigiPi
On the USB attached DRA's (and many other radio interfaces based on the CM series of chips), PTT is asserted by raising GPIO-3 on the CM119A codec chip. While this is a clever way to provide PTT and allows sharing the PTT function across multiple apps at the same time, it does require that the application software has the necessary code to access the GPIO lines on the codec (which present as an HID to the operating system). Many Ham applications have added this support, but not all. On DigiPi, the applications that use the underlying modems like Direwolf and FLdigi have this support. The WSJT suite does not (though we did try to get the devs to add it many times). The latest versions of ARDOP include support, but I haven't tested this on the version included with DigiPi. The other applications probably do not support the DRA-45. None of the apps will be set up by the Initialize function to support a USB DRA, you will have to edit the configuration manually. I haven't looked at hamlib in a while, but I don't think this supports was ever added there (maybe I should work on that).

Note that this does not apply to the DRA-Pi-Zero, which is fully supported on DigiPi. PTT on that device comes from the GPIO lines on the Pi itself.

Unfortunately, I do not believe the IC-706MKIIG supports PTT via CAT (CI-V) commands, so PTT has to come from some sort of hardware device. There are some DRA workarounds for other platforms, but not sure we could get them going on the DigiPi platform.

-Scott, NS7C

Felipe Guilfuchi Ramos

unread,
Oct 23, 2026, 8:39:21 PMOct 23
to DigiPi
I rebuilt my Digipi. Replaced the DRA-45 for a DRA PI ZERO. I also re-flashed my sd card.
Do I need to use a cat cable for proper operation of the Digipi with the IC-706MKIIG?
I'm thinking about frequency control as the PTT as I understand should work through the Dra Pi Zero.
Please clarify.
If cat control is problematic for the Digipi/IC-706MKIIG, i can consider manually tuning the frequency and eliminate it entirely.

Scott Currie

unread,
Oct 23, 2026, 8:51:44 PMOct 23
to DigiPi
You will still want the CAT cable for frequency/mode control.

-Scott, NS7C

Doug Reed, N0NAS.

unread,
Oct 26, 2026, 12:24:23 AMOct 26
to DigiPi
Yes, the 706MKiiG does have PTT over CAT via Hamlib as an option. It may be lacking on the earlier models. 
If you are using the mDIN6 data connector on the back panel it will have direct PTT control. 
I've used my 706 both ways at different times. I think I prefer the mDIN6 direct PTT over CAT PTT just in case the CAT connection crashes. 
If you leave the CAT baudrate at 9600 there will be a small extra delay for the CAT PTT command so bump the datarate higher?  
73, Doug Reed, N0NAS.

Felipe Guilfuchi Ramos

unread,
Oct 27, 2026, 3:39:39 PMOct 27
to DigiPi
After trying to get the Digipi to work with my radio CAT cable and the DRA-30, frustration set in and I sidelined the Digipi for a moment and decided to test this same setup with Winlink in my Windows PC. My PC also has VARA installed and I remembered operating my older IC-725 with this same equipment.
As it turned out, I found a wiring error in the radio to Dra-30 cable I had built. Once corrected, the setup worked nicely. I even configured Ardop which I had not done previously. 
My Windows installation does not use Hamlib. It uses UZ7HO soundmodem. It is much easier (for me) to setup than Hamlib. My setup does PTT through the DRA-30 and frequency control through the CAT cable.
I don't doubt that Hamlib can do this. I simply just don't know how to set it up and make it work. There are no easily obtainable instructions I can follow. 
I will continue to try and get it working. I will need to scour the internet for more information.
In the mean time, if somebody out there can send me links to setup instructions that are easier to follow (please note: I AM NOT A PROGRAMMER OR CODE PROFICIENT), I will be very grateful. 

Doug Reed, N0NAS.

unread,
Oct 28, 2026, 2:07:34 AMOct 28
to DigiPi
I noticed this in the POTACAT User Guide in the "other rig (Hamlib)" and using Icom radios section:   <https://docs.potacat.com/nested/rig-ic-7300.html> 

The IC-706MKIIG (CI-V address 58h) has a firmware quirk: it accepts CAT PTT but doesn’t route TX audio to the rear interface, so PTT must be keyed on the DigiRig’s hardware PTT line instead:

  • Set the PTT Port field in the rig’s Hamlib settings (Settings > Rig).
  • Two-port DigiRig: CAT on one COM port, PTT Port on the other COM port.
  • DigiRig Mobile (single port): CAT and PTT share one COM port — use the DTR/RTS pin selector (default DTR; some units key on RTS).
This 706 CAT PTT bug sounds a lot like your problem?? Goes into transmit but no audio?? I may have tried CAT PTT with my 706, but I know I only use it with PTT via the mDIN6 data connection.
The 706MkiiG user manual does show using the 13-pin connector or the mike jack for AFSK operation. I expect those inputs could use CAT PTT just fine but at the possible expense of disconnecting the mike each time? 

The <kv5r.com> web site has some good info about the IC-706MKiiG and says this about data modes:
For the usual “soundcard” modes you need an interface, such as a SignaLink or similar, not just a cable. The interface will contain chips to convert the radio’s CAT data signals and audio to USB. Order for (your) specific radio model. On the 706, that will use the 13-pin din “ACC” jack. The smaller 8 or 9 pin din “data” jack on the 706 is for the old data modems (Kantronics, etc), rarely used now.
73, –kv5r

Personally, I've used the mDIN6 data connector for all my data modes. A friend has a MKiiG (and earlier models) that he uses with the 13-pin ACC connector. We both use a Signalink USB with PTT through the cable, we don't use CAT for PTT. 
73, Doug Reed, N0NAS. 

Doug Reed, N0NAS.

unread,
Oct 28, 2026, 2:47:31 AMOct 28
to DigiPi
The DRA-30 is just a CM119A USB to audio interface board. It uses pin 13 of the CM119A chip to control the PTT output. Pin 13 is the same pin used by all CM108 adapters to control PTT. You might want to set the blue audio level pots to middle of the range before you start, unless you already have them adjusted from your Windows tests. 

Hamlib does the computer control of the radio. Within Hamlib you select the rig (Icom IC-706 MKiiG) and tell it what USB port your CAT/CI-V cable is plugged into. You need to set the serial port speed on the computer to be the same as in the radio. The 706 is usually 9600 baud by defaukt, but you should probably follow the directions in the 706 manual and check what the radio is currently set for. Craig could tell you if selecting a faster speed is a problem for the slower RasPi boards. I put a label on my radio to remind me what the CI-V port speed is for the next time I have to configure Hamlib. Finding the USB comm port number is often the hardest part of the setup. 
Good luck with your configuration. 73, Doug Reed, N0NAS. 

Felipe Guilfuchi Ramos

unread,
Oct 29, 2026, 10:51:58 AMOct 29
to DigiPi
Thanks for your reply.
I will follow your pointers when setting up Hamlib once I figure out how to get to it in Digipi.
73, Felipe Guilfuchi Ramos, WP4DMD

Reply all
Reply to author
Forward
0 new messages