AIOC board not recognised
Richard Edeson
Includes optional support for: gpsd hamlib cm108-ptt libgpiod dns-sd
Reading config file /run/direwolf.tnc.conf
Could not extract card number or name from default
Can't automatically find matching HID for PTT.
Audio device for both receive and transmit: default (channel 0)
Channel 0: 1200 baud, AFSK 1200 & 2200 Hz, A+, 44100 sample rate / 3, Tx AX.25.
Using /dev/hidraw0 GPIO 3 for channel 0 PTT control.
Ready to accept AGW client application 0 on port 8000 ...
Ready to accept KISS TCP client application 0 on port 8001 ...
DNS-SD: Avahi: Announcing KISS TCP on port 8001 as 'Dire Wolf on digipi'
Virtual KISS TNC is available on /dev/pts/0
Created symlink /tmp/kisstnc -> /dev/pts/0
DNS-SD: Avahi: Service 'Dire Wolf on digipi' successfully registered.
Now connected to IGate server euro.aprs2.net (85.90.180.26)
Check server status here http://85.90.180.26:14501
[ig] # aprsc 2.1.19-g730c5c0
[ig] # logresp G4FBA-2 verified, server T2CSNGRAD
[ig] G4FBA-2>APDW18:!R3:`UN5`S& ! DigiPi http://digipi.org/
And here's the direwolf.tnc.config. Much appreaciate any help please
# digipi TNC direwolf configuration file
# this file is used as a template by direwolf.tnc.sh
MYCALL G4FBA-2
# disable internet if crosstalk is an issue
# this is an issue with ISS/satellite stuff, we don't get credit for repeat
IGSERVER euro.aprs2.net
IGLOGIN G4FBA-2 13204
# put us on aprs.fi map via internet
# change sendto=IG to sendto=RF to send beacons over RF
PBEACON sendto=IG compress=1 delay=00:15 every=30:00 symbol="igate" overlay=R lat=53.832639 long=-1.056592 comment=" DigiPi http://digipi.org/"
# APRS Tracker
# Comment out above PBEACON line, uncomment both lines below
# You might need to edit /etc/default/gpsd to assign gps device file
#GPSD localhost
#TBEACON delay=00:15 every=10:00 symbol="igate" overlay=R via=WIDE1-1 power=5 height=5 gain=3 comment="DigiPi igate/tracker http://digipi.org/"
# data carrier detect, and push-to-talk pins
DCD GPIOD gpiochip0 16
# direwolf.tnc.sh will modify and uncomment one of these and copy to /run/direwolf*conf.
# Add PTT line BELOW these to override. DO NOT edit the following PTT lines, or uncomment
# them.
#PTT GPIOD gpiochip0 12
#PTT RIG RIGNUMBER DEVICEFILE
#PTT /dev/DEVICEFILE RTS
#PTT /dev/DEVICEFILE DTR
#PTT CM108 DEVICEFILE
DWAIT 0
TXDELAY 30
TXTAIL 10
AGWPORT 8000
KISSPORT 8001
Craig
it's finding the device here,
Using /dev/hidraw0 GPIO 3 for channel 0 PTT control.
device in SysInfo too.
also, the direwolf.conf in use is "/run/direwolf.tnc.conf" (dynamically generated
based on the one you just pasted).
-craig
KM6LYW
--
You received this message because you are subscribed to the Google Groups "DigiPi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to digipi+un...@googlegroups.com.
To view this discussion visit https://groups.google.com/d/msgid/digipi/82e4aa21-593f-4b86-8ef5-f74907528ba8n%40googlegroups.com.