Can 39;t Download On Cellular Network
Hedda Tillmon
A cellular network or mobile network is a telecommunications network where the link to and from end nodes is wireless and the network is distributed over land areas called cells, each served by at least one fixed-location transceiver (typically three cell sites or base transceiver stations). These base stations provide the cell with the network coverage which can be used for transmission of voice, data, and other types of content. A cell typically uses a different set of frequencies from neighboring cells, to avoid interference and provide guaranteed service quality within each cell.[citation needed][1]
When joined together, these cells provide radio coverage over a wide geographic area. This enables numerous portable transceivers (e.g., mobile phones, tablets and laptops equipped with mobile broadband modems, pagers, etc.) to communicate with each other and with fixed transceivers and telephones anywhere in the network, via base stations, even if some of the transceivers are moving through more than one cell during transmission.
Major telecommunications providers have deployed voice and data cellular networks over most of the inhabited land area of Earth. This allows mobile phones and mobile computing devices to be connected to the public switched telephone network and public Internet access. Private cellular networks can be used for research[3] or for large organizations and fleets, such as dispatch for local public safety agencies or a taxicab company.[2]
The increased capacity in a cellular network, compared with a network with a single transmitter, comes from the mobile communication switching system developed by Amos Joel of Bell Labs[4] that permitted multiple callers in a given area to use the same frequency by switching calls to the nearest available cellular tower having that frequency available. This strategy is viable because a given radio frequency can be reused in a different area for an unrelated transmission. In contrast, a single transmitter can only handle one transmission for a given frequency. Inevitably, there is some level of interference from the signal from the other cells which use the same frequency. Consequently, there must be at least one cell gap between cells which reuse the same frequency in a standard frequency-division multiple access (FDMA) system.
The history of cellular phone technology began on December 11, 1947 with an internal memo written by Douglas H. Ring, a Bell Labs engineer in which he proposed development of a cellular telephone system by AT&T.[5]
The first commercial cellular network, the 1G generation, was launched in Japan by Nippon Telegraph and Telephone (NTT) in 1979, initially in the metropolitan area of Tokyo. Within five years, the NTT network had been expanded to cover the whole population of Japan and became the first nationwide 1G network. It was an analog wireless network. The Bell System had developed cellular technology since 1947, and had cellular networks in operation in Chicago and Dallas prior to 1979, but commercial service was delayed by the breakup of the Bell System, with cellular assets transferred to the Regional Bell Operating Companies.
The wireless revolution began in the early 1990s,[6][7][8] leading to the transition from analog to digital networks.[9] This was enabled by advances in MOSFET technology. The MOSFET, originally invented by Mohamed M. Atalla and Dawon Kahng at Bell Labs in 1959,[10][11] was adapted for cellular networks by the early 1990s, with the wide adoption of power MOSFET, LDMOS (RF amplifier), and RF CMOS (RF circuit) devices leading to the development and proliferation of digital wireless mobile networks.[9][12][13]
The first commercial digital cellular network, the 2G generation, was launched in 1991. This sparked competition in the sector as the new operators challenged the incumbent 1G analog network operators.
With FDMA, the transmitting and receiving frequencies used by different users in each cell are different from each other. Each cellular call was assigned a pair of frequencies (one for base to mobile, the other for mobile to base) to provide full-duplex operation. The original AMPS systems had 666 channel pairs, 333 each for the CLEC "A" system and ILEC "B" system. The number of channels was expanded to 416 pairs per carrier, but ultimately the number of RF channels limits the number of calls that a cell site could handle. FDMA is a familiar technology to telephone companies, which used frequency-division multiplexing to add channels to their point-to-point wireline plants before time-division multiplexing rendered FDM obsolete.
The principle of CDMA is based on spread spectrum technology developed for military use during World War II and improved during the Cold War into direct-sequence spread spectrum that was used for early CDMA cellular systems and Wi-Fi. DSSS allows multiple simultaneous phone conversations to take place on a single wideband RF channel, without needing to channelize them in time or frequency. Although more sophisticated than older multiple access schemes (and unfamiliar to legacy telephone companies because it was not developed by Bell Labs), CDMA has scaled well to become the basis for 3G cellular radio systems.
The key characteristic of a cellular network is the ability to reuse frequencies to increase both coverage and capacity. As described above, adjacent cells must use different frequencies, however, there is no problem with two cells sufficiently far apart operating on the same frequency, provided the masts and cellular network users' equipment do not transmit with too much power.[1]
The frequency reuse factor is the rate at which the same frequency can be used in the network. It is 1/K (or K according to some books) where K is the number of cells which cannot use the same frequencies for transmission. Common values for the frequency reuse factor are 1/3, 1/4, 1/7, 1/9 and 1/12 (or 3, 4, 7, 9 and 12, depending on notation).[15]
Although the original cell towers created an even, omnidirectional signal, were at the centers of the cells and were omnidirectional, a cellular map can be redrawn with the cellular telephone towers located at the corners of the hexagons where three cells converge.[18] Each tower has three sets of directional antennas aimed in three different directions with 120 degrees for each cell (totaling 360 degrees) and receiving/transmitting into three different cells at different frequencies. This provides a minimum of three channels, and three towers for each cell and greatly increases the chances of receiving a usable signal from at least one direction.
Practically every cellular system has some kind of broadcast mechanism. This can be used directly for distributing information to multiple mobiles. Commonly, for example in mobile telephony systems, the most important use of broadcast information is to set up channels for one-to-one communication between the mobile transceiver and the base station. This is called paging. The three different paging procedures generally adopted are sequential, parallel and selective paging.
The details of the process of paging vary somewhat from network to network, but normally we know a limited number of cells where the phone is located (this group of cells is called a Location Area in the GSM or UMTS system, or Routing Area if a data packet session is involved; in LTE, cells are grouped into Tracking Areas). Paging takes place by sending the broadcast message to all of those cells. Paging messages can be used for information transfer. This happens in pagers, in CDMA systems for sending SMS messages, and in the UMTS system where it allows for low downlink latency in packet-based connections.
In a cellular system, as the distributed mobile transceivers move from cell to cell during an ongoing continuous communication, switching from one cell frequency to a different cell frequency is done electronically without interruption and without a base station operator or manual switching. This is called the handover or handoff. Typically, a new channel is automatically selected for the mobile unit on the new base station which will serve it. The mobile unit then automatically switches from the current channel to the new channel and communication continues.
The most common example of a cellular network is a mobile phone (cell phone) network. A mobile phone is a portable telephone which receives or makes calls through a cell site (base station) or transmitting tower. Radio waves are used to transfer signals to and from the cell phone.
Modern mobile phone networks use cells because radio frequencies are a limited, shared resource. Cell-sites and handsets change frequency under computer control and use low power transmitters so that the usually limited number of radio frequencies can be simultaneously used by many callers with less interference.
A cellular network is used by the mobile phone operator to achieve both coverage and capacity for their subscribers. Large geographic areas are split into smaller cells to avoid line-of-sight signal loss and to support a large number of active phones in that area. All of the cell sites are connected to telephone exchanges (or switches), which in turn connect to the public telephone network.
Since almost all mobile phones use cellular technology, including GSM, CDMA, and AMPS (analog), the term "cell phone" is in some regions, notably the US, used interchangeably with "mobile phone". However, satellite phones are mobile phones that do not communicate directly with a ground-based cellular tower but may do so indirectly by way of a satellite.
There are a number of different digital cellular technologies, including: Global System for Mobile Communications (GSM), General Packet Radio Service (GPRS), cdmaOne, CDMA2000, Evolution-Data Optimized (EV-DO), Enhanced Data Rates for GSM Evolution (EDGE), Universal Mobile Telecommunications System (UMTS), Digital Enhanced Cordless Telecommunications (DECT), Digital AMPS (IS-136/TDMA), and Integrated Digital Enhanced Network (iDEN). The transition from existing analog to the digital standard followed a very different path in Europe and the US.[20] As a consequence, multiple digital standards surfaced in the US, while Europe and many countries converged towards the GSM standard.
760c119bf3