Need help with NAT
Luciano
Everyone coming from the FastEthernet0/1.4 should reach 192.168.252.151 at
1761/tcp & 1768/tcp
Thus, FastEthernet0/1.4 is the outside interface, interface FastEthernet0/0
the inside
That's what I've tested...
Any help?
Thank you
[...]
!
controller E1 1/0
framing NO-CRC4
pri-group timeslots 1-31
!
interface Loopback1
ip address 10.10.10.252 255.255.255.255
!
interface FastEthernet0/0
ip address 192.168.252.1 255.255.255.0
ip nat inside
duplex auto
speed auto
no cdp enable
!
interface FastEthernet0/1
ip address 192.168.21.129 255.255.255.0
duplex auto
speed auto
no cdp enable
!
interface FastEthernet0/1.1
no cdp enable
!
interface FastEthernet0/1.2
encapsulation dot1Q 2
ip address 192.168.22.254 255.255.255.0
no cdp enable
!
interface FastEthernet0/1.3
encapsulation dot1Q 3
ip address 192.168.23.254 255.255.255.0
no cdp enable
!
interface FastEthernet0/1.4
description !!!!! NAT !!!!!
bandwidth 1000
encapsulation dot1Q 4
ip address 139.160.248.210 255.255.255.240
ip nat outside
no cdp enable
!
interface Serial1/0:15
no ip address
encapsulation ppp
dialer pool-member 1
dialer pool-member 2
dialer pool-member 4
dialer pool-member 3
dialer pool-member 5
dialer pool-member 6
dialer pool-member 7
dialer pool-member 8
dialer pool-member 66
dialer pool-member 9
dialer pool-member 88
dialer pool-member 10
dialer pool-member 11
dialer pool-member 20
dialer pool-member 12
dialer pool-member 13
isdn switch-type primary-net5
no cdp enable
ppp authentication chap
ppp multilink
!
interface Dialer1
no ip address
no cdp enable
!
interface Dialer3
[...]
!
interface Dialer4
[...]
!
interface Dialer5
[...]
!
interface Dialer6
[...]
!
interface Dialer7
[...]
!
ip nat inside source static tcp 192.168.252.151 1768 139.160.248.222 1768
extendable
ip nat inside source static tcp 192.168.252.151 1761 139.160.248.222 1761
extendable
ip classless
ip route 10.10.10.42 255.255.255.255 Dialer8
ip route 10.10.10.73 255.255.255.255 75.75.75.2
ip route 10.10.10.247 255.255.255.255 47.47.47.1
ip route 10.10.10.250 255.255.255.255 Dialer66
ip route 10.21.0.0 255.255.0.0 80.80.80.2
ip route 10.108.0.0 255.255.0.0 Dialer9
ip route 20.20.20.0 255.255.255.0 Dialer6
ip route 139.160.126.141 255.255.255.255 139.160.248.209
ip route 139.160.126.212 255.255.255.255 139.160.248.209
ip route 139.160.254.3 255.255.255.255 139.160.248.209
ip route 139.160.254.4 255.255.255.255 139.160.248.209
ip route 139.160.254.5 255.255.255.255 139.160.248.209
ip route 139.160.254.8 255.255.255.255 139.160.248.209
ip route 157.243.0.0 255.255.0.0 20.20.20.2
ip route 157.243.0.0 255.255.0.0 Dialer6
ip route 172.31.63.7 255.255.255.255 147.147.147.2
ip route 172.31.63.8 255.255.255.255 Dialer12
ip route 172.31.63.8 255.255.255.255 147.147.147.2
ip route 172.31.63.9 255.255.255.255 147.147.147.2
ip route 172.31.63.10 255.255.255.255 147.147.147.2
ip route 172.31.63.11 255.255.255.255 147.147.147.2
ip route 191.200.0.0 255.255.0.0 Dialer11
ip route 192.54.111.0 255.255.255.0 Dialer88
ip route 192.168.2.0 255.255.255.0 47.47.47.1
ip route 192.168.12.0 255.255.255.0 Dialer66
ip route 192.168.20.0 255.255.255.0 192.168.21.10
ip route 192.168.42.0 255.255.255.0 25.25.25.2
ip route 192.168.72.0 255.255.255.0 75.75.75.2
ip route 192.168.73.0 255.255.255.0 75.75.75.2
ip route 192.168.244.0 255.255.255.0 Dialer89
ip route 192.168.247.0 255.255.255.0 47.47.47.1
ip route 192.168.250.0 255.255.255.0 Dialer66
ip route 192.168.251.0 255.255.255.0 Dialer88
ip route 193.50.103.0 255.255.255.0 Dialer5
ip route 194.5.104.0 255.255.255.0 Dialer3
ip route 211.1.1.0 255.255.255.0 Dialer88
no ip http server
!
map-class dialer callback
[...]
dialer-list 2 protocol ip permit
dialer-list 5 protocol ip permit
no cdp run
!
dial-peer cor custom
!
line con 0
[...]
line aux 0
[...]
line vty 0 4
[...]
!
end
Luciano
Gosh!
kacwilso
> No one can help me? Is it a Cisco Guru forum.?
>
> Gosh!
You could setup a loopback interface and make that either nat inside
or nat outside. You may need to setup a route map to force the
traffic to that interface or just a static route.