Howdy,
Two things come to mind on this. I've had similar problem in the past
and one of these solved the problem.
1) Right-Click on the view and select "Lock View Focus", then, re-draw
your crop sketch.
2) The View already has a sketch - Right-Click on the view and if Crop
View -> Remove View is an available selection - select it to remove
any unwanted sketch entities.
Hope that helps
Howdy,
Hope that helps
Thanks for the reply, but no-go. I had mentioned that I made sure the view
focus was locked, but as I didn't create the drawing and am only rev'ing it,
I didn't think to look for poor techniques done by the original guy. So I
did look for anything out of the norm in the dwg view and found that while
he did draw construction lines, constrain them horizontally and vertically,
then created a point on one of the lines and constrained it to the center of
both lines, then constrained the that point concentric to the diameter in
order to form centerlines instead of just wisely using the centerline
feature, (LOL - Got to love the way some people work...) there was nothing
out of the norm and it still does not work. I'm about ready to do a redraw
just because I can't tell what other hidden gems are in there, and it's not
a complicated drawing/part....
IYM
TOP
Just cropping a regular ol' standard front view of a round part. Absolutely
nothing unusual about it. Has a section line through the center of it, but
it doesn't even have dimensions on it - those are all in the section view.
On a whim, I decided to start to make a new drawing of the part to see if
the problem duplicates, so I placed the exact same view on a new sheet (same
template as the old dwg), created the same section view, and then tried to
crop it on that sheet and the crop works - no problems, so it's got to be
something the guy did to the drawing format or he's got something "unusual"
in that view I just can't see that's screwing it up. By "unusual", I mean
poor drawing techniques. I described how this guy was making center lines,
but another example of his would be - I'd find unconstrained sections lines
that were supposed to be vertical, but were actually 1/4 degree off that (or
some that were vertical, but .00005" off the actual center of the part) and
I would have to waste time trying to find out why the section view was
screwed up, or why I couldn't add a radius dimension to it because it wasn't
a "true" radius...erg...so I know what to check for on his prints, but this
is a new one....
Anyway I ended up redrawing it, but I saved the old print as I eventually
want to know what's going on should I run across this again...
Thanks...
IYM
TOP
⚡️┏━━━━━━━🎰💥📢━━━━━━━┓⚡️
> ✅เข้าสู่ระบบเว็บเว็บสล็อต ▶️ https://he1.me/EISxU
> ✅สมัครสล็อตออนไลน์ ▶️ https://he1.me/EISxU
> ✅ติดต่อสอบถามสล็อต ▶️ https://he1.me/EISxU
> ✅สอบถามเพิ่มเติม ▶️ https://he1.me/EISxU
> ⚡️┗━━━━━━━🎰💥📢━━━━━━━┛⚡️
🎰เริ่มต้นที่ 1 บาท
🎰ฝาก-ถอนโอนไว ระบบออโต้
🎰ไม่มีขั้นต่ำ-ไม่ติดเทิร์น
🎰ไม่ล็อค 𝐔𝐒𝐄𝐑 ไม่ปรับอัตรา
🎰แอดมินบริการดีดูแล 24 ชั่วโมง