ERROR: No ClusterHAT/CTRL devices found -- clusterhat v2.5

64 views
Skip to first unread message

hanur13

unread,
Sep 19, 2021, 7:54:44 AMSep 19
to ClusterHAT
Hi,
I have cluster v2.5 running Banana Pi M2 Zero (BPi) on top of Raspbery Pi 3B+ (RPi)

I used BETA 64 bit versions of CNAT  for RPi and Armbian from Vasilis (CNAT) for BPi. 
The firstime I use the clusterhat I could use "clusterhat on" to power on all the BPi. 

Unfortunately after I reboot it, The RPi didn't detect clusterhat anymore.

-----------------

pi@cnat:~ $ sudo clusterhat on

ERROR: No ClusterHAT/CTRL devices found

------------------

pi@cnat:~ $ sudo systemctl status clusterctrl-init.service

● clusterctrl-init.service - ClusterCTRL init

   Loaded: loaded (/lib/systemd/system/clusterctrl-init.service; enabled; vendor preset: enabled)

   Active: failed (Result: exit-code) since Sun 2021-09-19 20:28:21 JST; 16min ago

  Process: 341 ExecStart=/sbin/clusterctrl init (code=exited, status=1/FAILURE)

 Main PID: 341 (code=exited, status=1/FAILURE)


Sep 19 20:28:20 cnat systemd[1]: Starting ClusterCTRL init...

Sep 19 20:28:21 cnat clusterctrl[341]: ERROR: No ClusterHAT/CTRL devices found

Sep 19 20:28:21 cnat systemd[1]: clusterctrl-init.service: Main process exited, code=exited, status=1/FAILURE

Sep 19 20:28:21 cnat systemd[1]: clusterctrl-init.service: Failed with result 'exit-code'.

Sep 19 20:28:21 cnat systemd[1]: Failed to start ClusterCTRL init.

---------------

I tried to re-flash image on BPi as well as install new image RPi with 32 bit version but similar above Error message is always appear.

Do you know how to troubleshoot it?


Nurul

Chris Burton

unread,
Sep 21, 2021, 3:37:53 PMSep 21
to ClusterHAT
Hi, 
I tried to re-flash image on BPi as well as install new image RPi with 32 bit version but similar above Error message is always appear.

Do you know how to troubleshoot it?

I'd advise running though https://8086.support/index.php?action=faq&cat=23&id=115&artlang=en which should help work out where the problem is.

Chris.
Message has been deleted

hanur13

unread,
Sep 25, 2021, 1:12:45 AMSep 25
to ClusterHAT
It worked after I used another type of image.
I wrote the answer on next group.
So I will delete the last question

Nurul

On Wednesday, September 22, 2021 at 4:56:50 PM UTC+9 hanur13 wrote:
Thank Chris,

It seems that I didn't connect the clusterhat properly. 
After I fix the connection, It can detect the clusterhat and I can run the "clusterctrl on" and all the P1-P4 LED is lit up.

Unfortunately, after 1-2 minutes the RPi (controller | cnat on my case) is freezed.
I assumed the controller couldn't strong enough to boot all the P1-P4 simultanously.

So, I tried to test the "clusterctrl on p1" only and It didn't freeze, finally.
However, I still cannot "ping p1" as well as "ssh pi@p1" even after I wait for around an hour.
--------------

pi@cnat:~ $ ssh pi@p1

ssh: connect to host 172.19.181.1 port 22: No route to host

pi@cnat:~ $ ping p1

ping: p1: Name or service not known

pi@cnat:~ $ ping 172.19.181.1 

PING 172.19.181.1 (172.19.181.1) 56(84) bytes of data.

From 172.19.181.254 icmp_seq=1 Destination Host Unreachable

From 172.19.181.254 icmp_seq=2 Destination Host Unreachable

From 172.19.181.254 icmp_seq=3 Destination Host Unreachable

-------------

Do you know how to troubleshoot that problem??
(Note, I am using 64Gb SDCard on p1)

Nurul

Tony Brack

unread,
Sep 25, 2021, 4:33:20 PMSep 25
to ClusterHAT
Take a peek at my post.  Do you see a memory (register) dump in messages?

Tony

hanur13

unread,
Sep 25, 2021, 8:36:35 PMSep 25
to ClusterHAT
No I didn't see it in my case.

I am not sure these are relate with your case, but I have different setting environment, such as:
- I am using Banana Pi M2 Zero for replacement of Pi Zero/W
- Armbian Image for my Banana Pi (download from Vassilis)
(note: perhaps you may want to try customise the images)
- CNAT mode

Have you see this blog, he used Pi Zero as well.

Nurul

Reply all
Reply to author
Forward
0 new messages