Hard Disk 3fo Problem

[Prisc Chandola]

TheSMART Hard Disk Error is a common error with HP laptops and desktop computers. The SMART diagnostic tool is included in the HP firmware. If the tool discovers an hardware issue during a scan, the SMART firmware displays the error message SMART Hard Disk Error. The most common version of this error is SMART Hard Disk Error 301.

There are several reasons for the error to occur, such as an outdated BIOS, a loose connection, a virus, file corruption, physical damages, an unexpected shutdown, problems with drivers and applications, or a power surge. Due to the many possible causes, there are different possible ways to get rid of SMART Hard Disk Error 301:

The hard disk error HARD DISK 1 (3F1) is a common error with HP laptops. It occurs when the laptop hard drive gets either corrupt or damaged, or when the operating system files are damaged. The full error message usually looks like this:

Are you facing the Boot device not found error, also known as hard disk error 3F0? This error is one of the most common problems faced by computer users. The hard disk error 3F0 occurs unexpectedly when the hard disk does not support the system boot process. The boot device not found error may be caused by an incorrect boot sequence in the BIOS, a connection issue, a malware attack, or damages of the hard drive itself.

There are several Master Hard Disk Errors that may occur on your computer, such as Primary, 3rd, 4th, or 5th master hard disk errors. These errors occur if you have a system with multiple hard drives. The number indicated which of your hard drives is having an issue.

The solution depends on what caused the error to occur. To solve the problem, access the BIOS settings and change the Drive Boot Order. This may fix the issue and enable the system to boot into Windows normally. You can also try troubleshooting with the Windows Recovery Environment (EN). Another helpful tool is the Error Checking tool by Windows, which helps you identify the most common hard drive errors.

There could be several possible reasons why you are facing the disk boot failure error message. Whenever you start your computer, the BIOS tries to find a bootable drive. The error message Disk Boot Failure indicated that the BIOS was unable to find a disk to boot from.

If you receive a cyclic redundancy check error, you are facing hard drive corruption problems. The error occurs due to misconfigured files, unsuccessful installation of programs, file corruption, or a cluttered disk.

If your computer is still covered under warranty, reach out to the HP support. If not, try to recover your data from the damaged hard drive using a data recovery tool. After recovering all data, replace the damaged hard drive with a new one.

ISS error 301 is a status code that informs the client that the location of a requested resource has permanently changed. If this server-side status comes up unexpectedly, you may want to diagnose the problem.

The first step to solve the problem is to check if there are any incorrect redirect instructions on the server configuration files or your web server software. You can also check the application logs to look for further information of the possible cause.

On a side note the only test that does fail, every time, is the video test but I have encountered no problems with video once PC is up and running, but the VGA and DVI ports work just fine, even with two monitors.

A hard disk warning at startup most likely means the disk is failing. Since you can still get it to work means that you should get a new drive, clone the old drive to the new drive and get the replacement installed before it is too late. IMHO, do the replacement now.

If the hard drive was replaced, what was the replacement(make amd model)? How was the OS reinstalled? Recovery Disk set or Windows install disk? Without the model number of the PC, it would be helpful, but it could actually be a motherboard fault. Some models have reported a controller failure that starts to manifest itself with an error reported that looks just like a hard drive failing.

I know someone mentioned the HD was bad, but I find it hard to believe that I bought a bad hard drive, after all I got this error message with the original HD, got a new one, installed it, and same message.

After calls to support and getting nowhere, I remembered that this model had a supplemental cache on the Motherboard which is a small circuit board held on by two small screws. Basically this is a type of SSD disk drive. It is designed to speed up access but many hybrid disk drives now include the same type of function directily on the disk. I removed the small circuit board and the problem went away. It made no difference in performance.

After hours of research, figured it out. My 16GB tiny mSATA SSD drive mounted on the motherboard had failed. this SSD acts as a cache to speed up boots, launching applications and other activities it "remembers" you have done before. It is NOT the boot disc. I tried to save it with MiniTool's Partition Wizard to no avail...so I opened up the case, took out one screw and removed the SSD.

I'd say, mtron, that you shouldn't worry about replacing it. I've long since forgotten about mine that I removed and did not replace. In fact, I've replaced my main Hard Drive with a 500GB SSD. Holy Crap! PC boots up in less than 20 seconds and all applications load and display nearly instaneously. That little mSATA is a useless relic.

I got a message that the boot drive does not exist. I have run the procedureces on the website (reset bios, removing the battery, reseating the hard drive, etc.) but still get the message tha the hard drive doesn't exist. The laptop (pavilion dm4, windows 7) was running fine last night. Never any indication of a problem. Any help would be appreciated.

If this doesn't work I'd like you to see if the BIOS is detecting an HDD at all by performing the built in hard drive test. This document covers the process. Let me know the result (if you're able to perform it) of this test.

I will await your response.

Thank you so much for hanging with me through this. I will try your suggestion this evening. Dumb question though - since the machine was operating on Windows, does booting on Linux cause any problems?

That is a good question! If you use the one I suggested, Knoppix, it will not be a problem. This is a "flavor" of Linux that runs by only using the CD drive and the RAM. So, unless you change/delete files or installed Knoppix to the hard drive, when you reboot and take out the Knoppix disc everything will be as it was.

If memory serves me correct Knoppix should "mount" any hard drives/partitions and put an icon on the desktop. It might be named something weird like /mnt/hd0. If you do not see anything like this on your desktop then Knoppix didn't detect the hard drive either which means it is surely dead.

HP sent some boot disks. So I tried those this afternoon. Changed the bios so that it read the CD, it started windows from the CD, then it gave me a dialogue box saying "No HDD". Then the machine shut it self down. Based on that, I am assuming that the HDD is completely shot? I was hoping maybe it was just an issue with the boot sector and once the machine was up an running from the boot disk, maybe I could access my data (excel, word, ppoints, etc.). But no luck. Any thoughts on next steps? I am nervous about taking the drive to one of the "hard drive data recovery" services as theres a lot of financial info, and I have no idea how reputable those places are. Maybe they are reputable, but I am always concerned about my personal info on some server somewhere.

In short, your hard drive IS failing and Windows diagnostic is reporting it. You can disable the notification if its getting too annoying (it is annoying actually), but you still need to check your disk with tools to confirm its health. CHKDSK is the first place to start, but I just use crystal disk info CrystalDiskInfo - Crystal Dew World [en] to have a quick glance.

On the web a lot of people say it is preferable to have an external hard drive for your recording because this relieves the load on the system disk (e.g. -home-studio-necessities-7-externaldedicated-hard-drive/ ) .

I had this exact problem with a WD Elements 3T USB drive and it turned out to be the 3m USB 3.0 cable I was using to connect to my MacBook Pro. I tried the original WD (which was too short for where I wanted to locate the drive) and everything worked fine. I then tried a 2m cable and that was OK as well. It seems some drives are more fussy with cable specs than others.

Same problem here, running Windows 7 64 bit and Cubase 7.5. Projects work fine running from my internal hard drives or my USB 2.0 drive but not when running from my USB 3.0 drive (clicks, silence and occasional loud noise bursts). I thought it had to with that I was using my USB 3.0 drive with a USB 2.0 port, but having installed a new Transcend PCI-E card providing USB 3.0 ports I still have the same problem.

I have five different USB3.0 drives and copied the project to each. Two WD My Passport drive. One WD desktop drive. And two Seagate desktop drives. I tried various combinations of cables and drives. In the end it was only drive that had a problem. The other works without issue. I tried defragging and optimizing the drive and it continued to fail.

Hi, I'm not able to access recordings on my main Q box with a message that says the service is currently unavailable, and when I switch the box on I get a message that says there's a problem with the Hard Disk Drive

That's usually a sign that the hard drive is failing. Turn the box off at the wall for a minute then power it back on and see if helps. It's probably likely that you'll need a replacement box though so you'll need to ring Sky and request one. You'll lose all your recordings I'm afraid.

3a8082e126