Bass Guitar 1 String

[Prisc Chandola]

Ipicked up the bass a few months ago, and I've noticed that when I'm playing something, the strings make loud clicky sounds when they hit the fret. This happens especially when I'm trying to play something fast, and when I jump between strings. How can I prevent this from happening? What could I be doing wrong?

Bradd has mentioned the two places where the string is most likely to be auidibly hitting the strings. Another couple of suggestions I have for reducing the direct 'left hand' noise made by the string where it's fretted -

Again as Bradd says, low action at the high frets will make it more likely for the string to clatter against the frets at the end of the neck, so you may want to raise the bridge saddles a little, as well as focusing on playing less hard (with your right hand). The latter may mean you need to turn your amp up a bit too, so you can play gently and let the amp do the work.

As No'am Newman mentions in a comment, bass clanks aren't a bad thing in themselves - I harness them in a couple of ways: - accenting strong notes in a bar with a bit of right hand 'clank' - setting my bass up so that the string hits the high frets briefly at the start of each note. coupled with distortion, this gives a great snorty rock sound. Of course if you don't want clanks, that's fine too.

There are two likely causes for this, depending on where the strings are clicking. If they click directly under your fingers, from the force of your fingertips striking the frets, then work on reducing the tension in your fretting hand. Proper fretting requires very little tension or force. Keeping it minimal will reduce percussive noises and will also reduce fatigue and the likelihood of injury.

If the strings click or buzz against the neck farther from your fingers, then the problem might still be tension, but in your plucking hand instead of your fretting hand. When playing fast, loud, or dynamic music it is easy to over-pick which can make the strings slap or buzz against the strings. Low action or low neck relief will exaggerate this noise, so you might want to adjust your bass setup in addition to easing off the picking hand.

From an instrument maker's point of view: aside from how you play, the setup of the bass makes a difference. There's always going to be some amplitude of string vibration that will buzz somewhere; it's a matter of taste what that amplitude is. The lower the action, the easier it is to fret and the less problems with intonation, but the easier it is to buzz. The higher the action, the less buzzing, but the more effort and possible intonation problems.

Those clicks would make it seem like you're hammering on too hard with the fretting fingers. Hammer-ons are a regular part of guitar and bass playing, to be able to play legato, but also so you can drink your pint while still playing the bass line in a gig. Hammer-ons don't need to be sledge-hammer-ons, though. The note will still play when you press down less harshly. Try all sorts of different attack modes, and a lot of the click will disappear. Of course, sometimes you'll want it, so go back to your original mode of playing.

Another cause may be the strings are too low, and are catching on the next fret or three, although often, this will manifest itself in a rattle as well. You may also be pulling the string up away from the finger board before letting go - sort of mini bow and arrow style. That's a common way to play when you're slapping and popping - it's the pop. A slap is also percussive in a different way, when you hit the string down onto the finger board. Again, that's percussive, and will produce a click, albeit a different one.

I'm with Tim, I think you're squeezing too hard. Try this, place your finger on the string and press very, very gently until the string just touches the fretboard behind the fret. Keep playing the string with your right (I presume) hand all this time. Notice the left hand pressure you needed when the note first comes out clear. That the most pressure you need to exert, even when paying fast.

I have the same issue as a new player. All the responses above are great help.If the plane of the string vibration is parallel to the fretboard that lowers the fretting noise significantly. Try to change the direction of your plucking gradually to find the best one.

This type of sound is solvable by either playing softer with the playing hand (not hitting the strings so hard) or doing some EQing. If your bass has a treble control, turn it down. Same with the amp or any pedals.

Adjusting your playing style for a given situation will not only open up your bass for new possibilities, but make you a more versatile player. You can then use the clanky sound to accent other notes without sacrificing treble in your normal tone.

I used to have the same issue, hitting the strings far, far too hard and always getting the clank. I've since lowered my action and learned to play a lot softer. I can now get that clank without too much extra effort and play fast lines with soft strikes of the fingers, which is way easier than trying to hit hard during a fast passage.

A lot of comments around fret buzz will rightly point out the importance of a setup, the truss rod, proper fretting technique, etc. But there's also a tendency for new players to focus intensely on getting the the placement of the fretting fingers right, only to buzz on the release.

Playing slowly to a metronome, just doing whole notes, playing and releasing, is a good practice to see not only how softly you can place a note, but release it. Be mindful of the relationship of your plucking fingers too, and see that you're pulling across, and not up, against the string. You will find a magic sweet spot with your fingers to both play short plucks (with the plucking finger also acting as a mute on release) and longer sustains.

Shop bass strings for less at Strings and Beyond. We have a wide range of four- and five-string bass strings for different tastes, preferences and playing styles. You can choose from coated or uncoated, nickel flat wound, round wound, half rounds, phosphor bronze, stainless steel and more. Whether you prefer to pluck, pick, slap or all of the above, we can help you get strings that are made for how and what you play.

At Strings and Beyond, you'll find everything you need from flat-wound bass strings for a warm, vintage sound to round-wound strings to bring out a brighter tone. Consider looking into half-round wound strings, which are round wound then ground down for a tone that falls between vintage warmth and round brightness. Or check out tape wound strings with nylon tape wrapped around the wire for a mellow sound and reduced wear on fretless fingerboards.

We also offer several products from Rotosound, such as their handmade flat-wound bass strings, nickel round-wound strings and black polymer-coated series strings. D'Addario's nylon tape wound, chrome, nickel wound, ProSteel and half-round electric bass guitar strings are available in different gauges. Other bass guitar string brands we carry include La Bella, Dunlop, Ken Smith, Fender and Elixir. With more than 500 products in stock, the perfect string set is at your fingertips.

While four-string and five-string are the most common styles, Strings and Beyond can help you string up any bass instrument. Use our filters to discover strings for a six-string, eight-string and even 12-string electric bass. We also have a large assortment of acoustic bass guitar strings along with strings for the double bass and bass ukulele. You can search for strings based on the scale length, speaking length and much more.

We recommend trying the many winding styles, gauges and coatings until you find the sound that suits you. Check out our Bass Guitar Help Guide for information that will get you started, such as the difference between steel and nickel bass strings.

Use the winding peg to loosen the E string until the wrapping relaxes. Then remove the old string, add the new string, tighten it on the tuning post and trim the excess wire. Repeat for each string. You should normally change one string at a time to keep tension in the neck, but it's okay to remove all the strings occasionally so you can clean the fretboard.

No. For starters, the strings are usually too large to fit through the tuning posts and bridge holes. Even if you could get them through, the bass strings would be too floppy because the scale length of a guitar is so much shorter.

Theoretically, you could, especially if you widen the bridge holes and tuning posts. However, the strings would again be too floppy for bass use, and tuning them to guitar tuning would put a lot more tension on the neck.

A four-string bass usually has about a 34-inch scale length and a five-string bass is about 35 inches. However, many manufacturers have shorter options (warmer tones) and longer options (brighter tones). Read our article on Bass Scale Length for more information.

3a8082e126