Download Huawei Modem Drivers

[Shawana Kallhoff]

HIi found new USB modem driver. On ML I was using huawei universal v 4.25.05 driver with bulitin connect feature trough network prefs. this driver still work on Mavericks but was little crappy took long time to connect. On device manufacturer I found new driver for MBA 2013 that is working better and is version 4.25.45 link is consumer.huawei.com/en/support/downloads/detail/index.htm?id=17263 named MobileConnectDriver for Mac Book Air 2013 from 31th august 2013. It connects faster but like previous driver it is not showing time on menu bar like in ML. where can i enable time for menu bar?

hey. it is E176, very old model. i use it without mobile connect app. just directly dialing trough network settings or trough menu bar icon. it is behaving differently like on ML. when i dial it shows connecting then authenticating. after that i see time all zeroes. but it seem it is frozen and no connection. after half a minute time in menu bar shows like 32 secs and counting up. then connection is working.

Hi , i am using Macbook pro(OS X 10.9) . i hav problems with Huawei usb modem , the device not detecting. (device model is E303D) . i installed MobileConnectDriver for Mac Book Air 2013 bt still not working. ?

A while back I installed a USB 3G modem (a Three Mobile Huawei D160G and Mobile Partner software) on my Windows 2008 64 bit development box. I immediately encountered a problem where upon starting a Windows 2003 Standard Edition VM in Virtual Server 2005R2 the host OS would crash with a Blue Screen of Death periodically.

The blue screen problems continued however and I noticed that the uninstaller hadn't removed the network adapter it created when the 3G software was installed. I deleted this but suspect that there's still something left over that's causing Virtual Server 2005R2 to BSOD.

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\hwcdcmdm0 HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\hwdatacard HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\hwusbapp HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\hwusbser

The hwdatacard registry entry has a value named ImagePath which points to system32\DRIVERS\ewusbmdm.sys. This file physically doesn't exist (presumably deleted at uninstall time) and it's definately related to the Huawei adapter (it has a DisplayName value of Huawei DataCard USB Modem and USB serial so I'm guessing all of the hw* entries above are related to this device.

The problem it seems isn't left over drivers from the 3G USB dongle, but a hardware fault on the machine. I flattened the machine and installed Windows 7 Ultimate and the problem remains where Virtual PC 7 does exactly the same thing.

I need to invoke a web request using Arduino via 3G Modem. I'm still looking for a solution but not found yet.

I'm living in Turkey and Assume that you need a 3G connection, you should buy 3G Modem from Turkcell or Vodafone because IMEI restrictions in Turkey. That's why i'm not using any Arduino 3G GRPS shields or other 3G modules. So that the best way is only buying 3G modem from a shop.

Anyway, i bought a Turkcell 3G modem (Huawei E3131C). I changed that HiLink mode can be switched to serial, using after installed win8.1 drivers (you can download HiLink drivers from here, -3G-Modem-Driver-4200500-Download-123430.html). Now, i can see COM ports to type AT commands. By using Putty, i set 3G modem as serial modem mode, typed AT^U2DIAG=0 (use

AT^U2DIAG=119 to return to HiLink mode). Until here eveything is fine. Now, how can i invoke a web request? For example, i need to call

I've encountered the same problem with LT4112 on a HP Folio 1040 G1 w/ Windows 8.1 X64, also full updated.

The problem originates with having issues connecting through the modem and getting "Limited Internet Access". Therefor we uninstalled the drivers to troubleshoot the modem, and now we can't get it back. Everything works flawless on Windows 7 X64 - but not Windows 8.1 X64.

The only time I've got it to work (WWAN+Sleep... and I hardly know how I did it) is when the gobi driver tells me that it's manufactured by Microsoft, and not MBB Incorporated. That's how it's delivered from HP out of the box. Managed to get it that way once, but don't remember how I did it. I think I tinkered with the COM-ports that appears after driver installation. Those COM-ports aren't there the looking at an OOTB machine.

I ran into a bug that crashed dwc2_lowlevel_hw_disable when using the dongle in "HiLink router mode" with kmod-usb-net-cdc-ether, so flashed the dongle to "stick mode" and now using kmod-usb-net-huawei-cdc-ncm instead.

it looks like some part of netifd may be confused whether the "option mode" clause should really be "option modes", when I added both options it silenced the error but didn't help the interface to start.

If I use minicom -D /dev/cdc-wdm0

I don't get any response to AT commands, but then if I try the same when the stick is plugged into the Fedora PC, I get no responses either, so that may not be significant

Wrt the config: Did /dev/cdc-wdm0 work as an AT command management device in Fedora? IIRC, different Huawei firmwares beahve differently here. But if the /dev/ttyUSBx device works, then I guess this isn't important.

This is misleading at best. That might have been the original meaning, but the option driver is now a multi-vendor generic fast USB serial driver. And it specifically supports the serial functions of most Huawei 3G and LTE modems.

That is pointless. Did you try this yourself? The usb-wwan module is only a support module with some shared functions for option, qcserial and ipw drivers. It supports no modems by itself. But the option driver depends on it, so it will be installed when you install it.

It can be a bit confusing, because you have to use the /dev/cdc-wdm0 on some Huawei modems. On most you can use either the /dev/cdc-wdm0 or the /dev/ttyUSBx devices. And yet another bunch is like yours where you have to use /dev/ttyUSBx.

Not sure how far it's getting with that, but "ip route show" doesn't have anything on the wwan0 interface, and the interface has no IP address, Interface still shows "up" but without receiving any bytes ...

Actually I just ran modemmanager in debug mode

however the output is too big to paste here,

I tried to upload as an attachment, but it apparently I'm only authorised to upload ,jpgs etc

can someone authorise me to upload a .txt file?

i had the same problem. only one usb port is not recognized for the huawei modem. if the modem connected to other usb ports its works.

i tried following

1. restart the pc

2.used another data cable

3. clean the usb port and tested with other usb drives its works

None of the suggestions posted here helped. However, on further research, I came across -e160g-the-device-has-been-disconnected-or-is-unavailable/, following whose suggestion worked for me. Just thought of posting it here to help others..

hi i have a huawei e 220 and mi problem is that it dosnt recognize mass storage ,it recognize 3 data interface wich is modem drivers and 1 cpm[psite, when i instal firmware last 20% of instalation just jump to end , says firmware update complete and when i reconect the modem to usb software dont start, it just shows that it recognize modem and composite

Hi everyone..I have a problem with my modem huawei e220. The problem is..when modem konekted the computer, modem is normal..connect and disconnect itself. But when i use my simcard, the problem appearing. The modem conect the computer more less one second, then disconnect again in one second to. That even contionously happen. my Question, what wrong with my modem. And, how i can solve that problem?

What type of coverage is the customer located in?

Is the customer able to get network?

Help the customer search for the Network manually, refer Modem Software Navigation for help.

Help the customer change the bandsettings to and search for Network Manually,refer Modem Software Navigation for help

Inform the customer that we have to perform an isolation test to determine the actual issues.

Note: No faults should be raised for marginal coverage .

My device driver is not getting installed after following the above instructions. So I went to the Reliance Website and downloaded the new driver suitable for my device

-netconnect-driver-download/

I hope below will work

1. Unisinstall the Reliance Netconnect software and delete the USB drivers

2. Connect your Reliance Broadband device then Install the new Netconnect driver that you have downloaded.

Hi guys, I haves a Huawei e220 mobile modem. I can get it to connect to internet through my laptop, and it works. But when I disconnect the USB from my laptop, I lose everything.

I no idea on how to keep the modem live so that I can use it outside my home (after all that was the purpose of buying it), so any help you can give me, please.

Thanks

I tried with another data card (Reliance 3g) and the device list is still empty. But with it I can at least connect. Any Idea how I can resolve it.

BTW the Huawei data card has been unlocked with DFS 3.3.0.7. Could that be the problem?

Thank you . Your method worked the second tome i tried it. All you need with a reliance netconnect Huawei modem is to connect the USB modem just when the machine is restarting. Then if the installation of the USB modem doesnt happen on its own, force install it by running the AutoRun.exe which is on the modem itself (go to my computer, and click on the usb drive where the reliance netconnect Huawai modem is connected)

hi frnds i unlocked my airtel huwaie modem when i inserted another sim card it is recognising tht sim but it is unable to connect even after sometime if it connects internet is not accessing so pleasehelp meeeee

So, obviously, the stock image I installed does not support ppp filtering. I did the test above because if I compile the kernel myself and enable PPP and USB ACM options as indicated in the article above, then I am unable to see the modem mount as a ttyUSBx or ttyACMx device.

3a8082e126