Removing rear sight on a High Standard 107

[Marty Goodman]

Can anyone here describe how to remove the rear sight on
A High Standard 107 Supermatic?
Thanks in advance.

[Pauley, Dan (RR Energy Systems)]

> Can anyone here describe how to remove the rear
> sight on A High Standard 107 Supermatic?

Doesn't that have the bridge mount rear sight? I've heard horror
stories about people trying to put those bridge sights back on after
being removed.

I'm thinking a red dot will mount right to the barrel and go over the
top of the rear sight. But to answer your question, no, I don't know
how to remove the sight especially if you want to be able to reuse any
of the parts.

R. Dan Pauley

[John]

Try this site:
http://home.roadrunner.com/~jbarta/hssight.pdf
(Thanks to the late Jim Barta)
John

--
You received this message because you are subscribed to the Google Groups
"Bullseye L list" group.
To post to this group, send email to bullsey...@googlegroups.com To
check out the online Bullseye Forum www.bullseyeforum.net

To join this group, send e-mail to
bullseye-l-l...@googlegroups.com
To leave this group, send email to
bullseye-l-li...@googlegroups.com

For more options, visit this group at
http://groups.google.com/group/bullseye-l-list?hl=en?hl=en
---
You received this message because you are subscribed to the Google Groups
"Bullseye L list" group.
To unsubscribe from this group and stop receiving emails from it, send an
email to bullseye-l-li...@googlegroups.com.
For more options, visit https://groups.google.com/groups/opt_out.

[Jack H]

With the slide off and you watch inside real carefully, you may not need to do all of the first four. first 1. remove the adjusting screw and plunger at the rear. 2. remove the sear spring pin and spring 3. remove the sear pin and sear. 4. remove the side plate so the safety can be removed. The tab on the safety must not be upset. then 1. drive the rear roll pin into the frame where the sear spring was. 2. drive the mated large pins apart. First one by inserting a punch through the small hole in one side. Then a larger punch to remove the second half. 3. drive each of the side roll pins in to just clear their side of the bridge. Too far and they will hit the other side bridge leg. Use proper punches and support the frame well. Note the positions of parts removed. Be sure to place the sear spring legs into the plunger notch on reassembly. While the slide is off, note the range of effective motion of the plunger on the sear spring. Do not set it too tight it cramps the sear or too loose to where the plunger is not under some pressure. --- On Sat, 2/23/13, John <jw...@nycap.rr.com> wrote:

From: John <jw...@nycap.rr.com> Subject: RE: {Bullseye L List} Removing rear sight on a High Standard 107 To: "'Marty Goodman'" <mart...@charter.net>, bullsey...@googlegroups.com Date: Saturday, February 23, 2013, 6:56 PM

Try this site: http://home.roadrunner.com/~jbarta/hssight.pdf (Thanks to the late Jim Barta) John -----Original Message----- From: bullsey...@googlegroups.com [mailto:bullsey...@googlegroups.com] On Behalf Of Marty Goodman Sent: Saturday, February 23, 2013 8:48 PM To: bullsey...@googlegroups.com Subject: {Bullseye L List} Removing rear sight on a High Standard 107 Can anyone here describe how to remove the rear sight on A High Standard 107 Supermatic? Thanks in advance. -- You received this message because you are subscribed to the Google Groups "Bullseye L list" group. To post to this group, send email to bullsey...@googlegroups.com To check out the online Bullseye Forum www.bullseyeforum.net To join this group, send e-mail to

bullseye-l-list+subs...@googlegroups.com

To leave this group, send email to

bullseye-l-list+unsub...@googlegroups.com

For more options, visit this group at http://groups.google.com/group/bullseye-l-list?hl=en?hl=en --- You received this message because you are subscribed to the Google Groups "Bullseye L list" group. To unsubscribe from this group and stop receiving emails from it, send an

email to bullseye-l-list+unsub...@googlegroups.com.

For more options, visit https://groups.google.com/groups/opt_out.

-- You received this message because you are subscribed to the Google Groups "Bullseye L list" group. To post to this group, send email to bullsey...@googlegroups.com To check out the online Bullseye Forum www.bullseyeforum.net

To join this group, send e-mail to bullseye-l-list+subs...@googlegroups.com To leave this group, send email to bullseye-l-list+unsub...@googlegroups.com

For more options, visit this group at http://groups.google.com/group/bullseye-l-list?hl=en?hl=en --- You received this message because you are subscribed to the Google Groups "Bullseye L list" group.

To unsubscribe from this group and stop receiving emails from it, send an email to bullseye-l-list+unsub...@googlegroups.com.