Gs44b Gs54b Nm-c561 Schematic
Billy Cromer
When repairing electronic products, engineers often encounter problems finding the drawings, especially for legacy products; the circuit diagrams may no longer exist. In this case, to analyze and improve the product, it is necessary to draw a circuit diagram based on the actual product. The skills of this operation are as follows:
2. When an engineer is printing a circuit board, be sure to label the components and pay attention to the regularity of the serial number. They cannot randomize or remember which one to write. Write and arrange according to a particularorder and rules to ensure that it is not easy to make mistakes in the drawing process.
3. Without marking the serial number of the components, if the engineer wants to improve analysis and proofreading, you have to number the components yourself. It is not annoying;otherwise, the later work will be more difficult. Important components must be marked so that they will not be missed in the process of drawing the schematic.
4. Correctly distinguish the various wires on the circuit board. There are various wires on the circuit board,such as power wire, ground wire, signal wire, These wires have different layout positions, rules, and functions. When drawing a schematic, you must figure it out.
5. When drawing a sketch, be sure to use transparent tracing paper and mark it with colorful pens. It is convenient to identify, modify,and analyze the circuit to reduce errors. In addition, when drawing a circuit diagram, try to find a similar circuit diagram for reference so that there is a multiplier effect, which is very worthy of reference for newcomers.
It can be seen from the introduction that the process of converting a PCB to a schematic diagram is not difficult. Still, many novices lack experience or have not operated before, so they will find it challenging to convert PCB into schematics.
This article takes the 4 Port Serial Interface, provided by Protel 99Se, as an example. Open the PCB diagram, select the menu File-Export, export the Protel network table; the file name is abbreviated as Serial.Net. 2. Start the program Omninet for Windows, select Protel as the input file type (Type). In Input File 1, use Browse to specify the location of the netlist file. Select EDIF as the output file type (Type). In Output File 1, specify the file name and path of the output file. Then click Run (the running icon).
It should be noted that this conversion may be useful for those with fewer components on the PCB. If there are many components on the PCB, the converted schematic diagram will be very large, and the network connection is extremely complicated. At this point, it is still difficult to interpret due to the lack of hierarchy or main thread. It is also not to be divided into multiple sub-graphs, and all networks are all connected.
The electronic engineering industry is so vast and rapidly growing that technology is evolving day by day. There are currently numerous open-source software or Electronic Design Automation (EDA) or CAD software available to help designers design their electronic circuits and lay the PCB design along with tools available in the software to generate files that will be used directly by PCB fabrication house.
Among these software, the most popular one is ALTIUM designer. The Altium Designer 18 will be discussed in this article. The Altium Designer gives you a complete platform where you can turn your imagination and ideas into reality.
The first step in turning the idea into reality is to do manual design or hand sketch on paper. This gives a clear understanding to the designer to know what he is looking for. Now the design on paper will be transferred to a CAD software like Altium. This process is called schematic capture. Having knowledge of the software, an expert will professionally capture the design in the schematic window.
You can save your PCB project and schematic file with *.PrjPcb and *.sch extensions respectively. After saving, you can now start the placement of components from the library on the rightmost menu. You can add the manufacturer libraries available directly from the Altium website.
The left panel shows the project files like schematic Diagram, PCB, Gerber, BOM, and other files are shown as sub-folder files inside the main project. Any changes made in the schematic will mark with a red symbol on the left panel schematic file. After you save changes, the red mark will disappear.
You can also annotate your components designators by Tools >> Annotation >> Annotate Schematics. You can change the sheet size by Right Panel Properties >>Page Options >> Formatting and Size >> Custom, and change the values of width and height according to needs, and change orientation to landscape or portrait. You can also switch between the units of measurement mm and mils.
The schematic capture is the basis of the PCB layout coming in the next step. Hence schematic capture should be completed free of errors. There should not be any error in the schematic design, and it must be cross-checked by another verification engineer to evaluate for any faults in the design. Otherwise, the wrong schematic will be translated into PCB and cause PCB not to function as expected.
Now the next step is the PCB layout step. Right-click on Project panel >> Add new to Project >> PCB layout. A black color window will appear. This is the PCB layout documents where you will design the PCB layout. Now go to the schematic window and do the following:
Now go to Design >> Rules. You can edit the PCB layout design constraints according to the PCB fabrication house capacity and limits and your design requirements. This is very important because while laying out PCB design (e.g., routing, placement of components, holes, vias, and other inner and outer layers), if there are violating constraints, the Altium will give you an error and will not proceed.
Now go to Route >> Auto Route >> All >> Route All. This will help you automatically route your components placed on the PCB according to the rules defined in the design rule wizard. The auto-routing will save ample time and effort but may not be a good choice when special care is needed for special ICs for EMI and other thermal considerations.
1. Select electronic components such as integrated circuits, transformers, transistors, etc., which are bulky, have many pins and play a major role in the circuit, and then draw from the selected reference pins to reduce errors.
2. If the component number (such as VD870, R330, C466, etc.) is marked on the PCB, since these serial numbers have specific rules, the components with the same Arabic numerals after the English alphabet are the same functional unit, so the drawing should be used. Correctly distinguishing the components of the same functional unit is the basis of the drawing pcb layout.
3. If the serial number of the component is not marked on the printed board, it is best to number the component yourself for easy analysis and proofreading. When designing printed circuit board components, the manufacturer generally arranges the components of the same functional unit relatively in order to minimize the copper foil routing. Once you find a device that has a core function, you can find other components of the same functional unit as long as you can find it.
4. Correctly distinguish the ground, power and signal lines of the printed board. Taking the power supply circuit as an example, the negative terminal of the rectifier connected to the secondary of the power transformer is the positive pole of the power supply, and a large-capacity filter capacitor is generally connected between the ground and the ground, and the capacitor casing has a polarity mark.
The power and ground lines can also be found from the three-terminal regulator pins. When the factory is wiring the printed circuit board, in order to prevent self-excitation and anti-interference, the ground copper foil is generally set to the widest (high-frequency circuits often have large-area grounded copper foil), the power supply copper foil is second, and the signal copper is used.
The foil is the narrowest. In addition, in electronic products with both analog and digital circuits, the printed boards often separate their ground lines to form an independent grounding grid, which can also be used as a basis for identification and judgment.
5. In order to avoid excessive wiring of the components, the wiring of the circuit diagram is cross-interleaved, resulting in a messy picture, and the power supply and ground lines can be used in a large number of terminal markings and grounding symbols. If there are many components, the unit circuits can be drawn separately and then combined.
6. When drawing a sketch, it is recommended to use transparent tracing paper, and use a multi-color pen to draw the ground wire, power cable, signal wire, components, etc. by color. When modifying, gradually deepen the color to make the drawing visually eye-catching for analysis of the circuit.
7. Proficiency in the basic composition of some unit circuits and classic drawing methods, such as rectifier bridges, voltage regulator circuits and op amps, digital integrated circuits. These unit circuits are directly drawn to form a frame of the circuit diagram, which can improve the drawing efficiency.
We also use third-party cookies that help us analyze how you use this website, store your preferences, and provide the content and advertisements that are relevant to you. These cookies will only be stored in your browser with your prior consent.
Necessary cookies are required to enable the basic features of this site, such as providing secure log-in or adjusting your consent preferences. These cookies do not store any personally identifiable data.
Lenovo G50-70 ACLU1/ACLU2 NM-A272 REV:1.0 2013-12-05 Bios bin file download.We are believing in reviving the technology and making minimum electronics waste, as our field is computers and laptops we are here trying to provide as much stuff as possible for free to make our contribution. At this platform you can download confirm and tested bios files, schematics and other relative material to make it possible to repair.
c80f0f1006