Leaky lamps!!
wallace myers
----------------------------Original message----------------------------
Hi Folks:
I made some oil lamps out of stoneware, glazed them
inside and out and fired them to cone 6. I gave them to
friends, who now tell me that they leak. What's going on?
I thought that clay vitrified at cone 6 and should not leak
even without glaze. If someone has a clue would you please
inform me.
Wallace
LOWELL BAKER
----------------------------Original message----------------------------
I just responded to a CM question concerning the same thing. Oil
will pass through the lamp body. The solution is one of several
things. Wash the inside of the lamp base with a thinned Elmers Glue
or a polyurathane varnish. allow to dry thoroughly (this may take a
week or more). Then test with lamp oil.
Interestingly enough water will not pass through the same clay body
because the water is sets up a kind of surface tension which dams the
small (minute) passages.
Read your CM questions section in the last edition for more on the
subject.
W. Lowell Baker
the University of Alabama
P.S. I had to call the Chemestry guys for the answer to this one.
Isak Isaksson
----------------------------Original message----------------------------
-----Ursprungligt meddelande-----
Fren: wallace myers <mye...@bardstown.com>
Till: Multiple recipients of list CLAYART <CLA...@LSV.UKY.EDU>
Datum: den 13 april 1998 16:07
Dmne: Leaky lamps!!
-------------------
Hallo over there.
The oil you are using is probably `lampoil` made from / or just carrosine.
That kind of oil is used to find cracks in steel. The oil find it`s way in
smal cracks down to 10/ 1 mm, and if you fire a clay to C/6 it perhaps
become stoneware on the outside, but not in the middle. Not every clay
vitrifies at C/6, that depends on the parts in the clay!
Check the composition of the clay and fire to C/8-9
Isak /Sweden
is...@saah.com
www.saah.com
Mike Flood
----------------------------Original message----------------------------
wallace myers wrote:
>
> ----------------------------Original message----------------------------
> Hi Folks:
> I made some oil lamps out of stoneware, glazed them
> inside and out and fired them to cone 6. I gave them to
> friends, who now tell me that they leak. What's going on?
> I thought that clay vitrified at cone 6 and should not leak
> even without glaze. If someone has a clue would you please
> inform me.
> Wallace
My partner and I have tried to seal cone 6 fired oil lamps with no
success. We tried glazing both inside and out, and we tried a lampliner
product. The lampliner product works about 50% of the time. We finally
gave up and are using glass globes to hold the oil on top of a clay
base.
The reason for the problem has something to do with the chemical
composition of water versus the composition of oil and the way the
molecules bind together. All I know is that we tried for several years
to solve this problem with no success.
Bridget MCDermott Flood
fireworks pottery
St. Louis, MO
Mark Issenberg
----------------------------Original message----------------------------
Hey Wallace i make cone 10 lamps and i would think they would leak also
so buy lamp sealer from Axner. You could make RAKU lamps as long as they
are sealed. So go buy some sealer.
Mark in Miami
_____________________________________________________________________
You don't need to buy Internet access to use free Internet e-mail.
Get completely free e-mail from Juno at http://www.juno.com
Or call Juno at (800) 654-JUNO [654-5866]
Caroline and Hedley Saunders
----------------------------Original message----------------------------
I had the same problem with some little glazed stoneware oil lamps, oil
seeped through the unglazed base. I ended up coating this area with
super-glue which seemed to provide a seal. Though I still warned users to
beware! I never did find out why it happened but it did, it is a while ago
but I expect I used a grogged body, I wonder if a smooth body burnished
would make a difference?
Caroline Saunders
del...@eclipse.co.uk
OWL POTTER
----------------------------Original message----------------------------
The problem with unreliable oil lamp liners might be not letting them dry long
enough.
I have had a lot of problems with leaky lamps until I learned to let them dry
thoroughly. Keep in mind, that is a very closed space trying to get rid of a
lot of moisture through a small opening. For mine, 5-7 days of drying is
necessary during the humid months here in Michigan. I've tried to hurry this
time by placing them on top of cooling kilns, but then they were sometimes
getting too hot and the liner was disappearing!
Carolynn Palmer, Somerset Center, Michigan
Cindy
----------------------------Original message----------------------------
Wallace,
If you don't want to use shellac or glue or lamp sealer, or whatever to
keep your lamps from leaking, you might experiment with different clay
bodies. According to a recent CM, glazes don't necessarily prevent oil from
getting to the clay body. I use many different glazes of different
formulations, however, and none of them leak so far--even one commercial
one (which I no longer use) that tended to craze never leaked. I use
Brownstone with grog from Dakota Potter's Supply (605-673-332-1946), for
those of you who live close enough to Sioux Falls to make that knowledge of
any use.
Cindy Strnad
Earthen Vessels
Custer, SD
USA http://blackhills-info.com/a/cindys/menu.htm