CP2918 and CP3918 and CNC extension C9900-E909

[Carlos Bou Gerges (automate)]

If you need just the below CP and CNC extension, check below description and attached full documents “CP2918-0000 and C9900-E909”:

CP2918-0000	Multi-touch built-in Control Panel CP29xx-0000 with DVI/USB Extended interface, 18.5-inch display 1366 x 768, Display only, Multi-finger touch screen	– aluminium housing with glass front, front side IP 65, rear side IP 20 – multi-finger touch screen – multi-finger touch screen driver for Windows 7 – single-finger touch screen driver for Windows XP and Windows CE 6 – integrated DVI/USB extension technology – DVI-E and USB-E 2.0 enable remote panel operation at a distance of up to 50 m from the PC. – USB-E 2.0 transmits USB 2.0 with 480 Mbit/s. – DVI-E input is compatible to the standard DVI output of a PC. – USB 3.0 input for the direct connection to a standard USB output of a PC with distances of up to 3 m – 2-port USB 3.0 socket inside the Control Panel backplane, for USB-E 2.0 limited to USB 2.0 – all connectors at the lower rear side – 24 V power supply – operating temperature 0…55 °C – pull-out clamping levers for fast installation without loose parts
C9900-E909	CNC push-button extension	Built-in CNC push-button extension C9900-E909                        - aluminium front with sheet-steel rear cover                         - front side IP 65, rear side IP 20                                  - 1 emergency stop key, type RAFI RAFIX 22FS+,                         2 NC contacts are directly wired to a 16 pole Phoenix                plug-in connector, 1 NO contact is readable via EtherCAT - 3 push-button keys with signal lamp, type RAFI RAFIX 22FS+,   first NO contact readable via USB, second NO (NC) contact   is directly wireable via a terminal row, all signal lamps   are transmitted via EtherCAT only, inscription of the keys via   slide-in label - 45 membrane keys with a LED via EthereCAT interface, inscription   of the keys via slide-in label - 2 Graycode switches T=32, controlled via EtherCAT, inscription   of the keys via slide-in label - connection of the CNC push-button extension via 2 RJ45 EtherCAT   sockets and a 16 pole Phoenix plug-in connector - pull-out clamping levers for fast installation without loose   parts

If you need the below CP and CNC check below descriptions and attached full documents  “CP3921-1500-0000”:

CP3921-1500-0000	CNC Multitouch Control Panel with DVI/USB extended interface         - 21,5 inch display 1920 x 1080                                      Aluminium housing with glass front, protection class IP 65           Multi finger touch screen                                            - Multi finger touch screen driver for Windows 7                     - Single finger touch screen driver for Windows XP                   Integrated DVI/USB extension technology:                              - DVI-E and USB-E 2.0 allow up to 50 m distance between the Panel and   the PC                                                             - USB-E 2.0 transmits USB 2.0 with 480 MBit/s                        - DVI-E input is compatible to the standard DVI output of a PC       connection over 2 connectors IP 65 for DVI and USB-E 2.0 in the      mounting arm adapter plate                                           operating temperature 0 ... 55 °C                                                                                                           - C9900-M753 rotatable and tiltable mounting arm for Rittal and        Rolec mounting arm systems with 48 mm tube from bottom             - C9900-E274 1 port USB socket at the mounting arm adapter, USB-A      with screw-on cap IP65, accessible from outside - CNC push-button extension:   - Emergency stop, 2x NC direct wired, 1x NO via USB   - 3 buttons, red, green, white, controlled via USB, labelling via     slide-in label   - 45 PLC special keys with yellow LEDs, controlled via USB,     labelling via slide-in label   - 2x graycode switch with 32 positions, controlled via USB,     labelling via slide-in label   - connector 19 pole, IP 65, for power supply and emergency-stop - Button series with push-buttons on the bottom side of CNC push-   button extension   - 12 push-buttons, green, red, 10x white. 1x NO and LED readable     via USB, labelling via slide-in label
CP3921-1502-0000	CNC Multitouch Control Panel with DVI/USB extended interface         - 21,5 inch display 1920 x 1080                                      Aluminium housing with glass front, protection class IP 65           Multi finger touch screen                                            - Multi finger touch screen driver for Windows 7                     - Single finger touch screen driver for Windows XP                   Integrated DVI/USB extension technology:                             - DVI-E and USB-E 2.0 allow up to 50 m distance between the Panel and  the PC                                                             - USB-E 2.0 transmits USB 2.0 with 480 MBit/s                        - DVI-E input is compatible to the standard DVI output of a PC       connection over 2 connectors IP 65 for DVI and USB-E 2.0 in the      mounting arm adapter plate                                           operating temperature 0 ... 55 °C                                                                                                          - C9900-M752 rotatable and tiltable mounting arm for Rittal and        Rolec mounting arm systems with 48 mm tube from top                - C9900-E274 1 port USB socket at the mounting arm adapter, USB-A      with screw-on cap IP65, accessible from outside - CNC push-button extension:   - Emergency stop, 2x NC direct wired, 1x NO via USB   - 3 buttons, red, green, white, controlled via USB, labelling via     slide-in label   - 45 PLC special keys with yellow LEDs, controlled via USB,     labelling via slide-in label   - 2x graycode switch with 32 positions, controlled via USB,     labelling via slide-in label   - connector 19 pole, IP 65, for power supply and emergency-stop - Button series with push-buttons on the bottom side of CNC push-   button extension   - 12 push-buttons, green, red, 10x white. 1x NO and LED readable     Via USB, labelling via slide-in label