Skip to first unread message
jennifer Dsilva
Aug 31, 2019, 1:23:10 AM8/31/19
to BeagleBoard
Hi,
I am using Linux 4.4.62 kernel and u-boot-2017.05-rc2 source code.
I am trying to do TFTP boot with nfs mounting.My U-boot commands executing the TFTP boot logs properly.But when i am trying to boot from uEnv.txt below i am getting this logs..
ubuntu@ubuntu-MS-7A15:~$ sudo minicom
[sudo] password for ubuntu:
Welcome to minicom 2.7.1
OPTIONS: I18n
Compiled on Aug 13 2017, 15:25:34.
Port /dev/ttyUSB0, 09:19:44
Press CTRL-A Z for help on special keys
U-Boot SPL 2017.05-rc2 (Aug 30 2019 - 11:30:01)
Trying to boot from MMC1
*** Warning - bad CRC, using default environment
reading u-boot.img
reading u-boot.img
U-Boot 2017.05-rc2 (Aug 30 2019 - 11:30:01 +0530)
CPU : AM335X-GP rev 2.1
I2C: ready
DRAM: 512 MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - bad CRC, using default environment
<ethaddr> not set. Validating first E-fuse MAC
Net: cpsw, usb_ether
Press SPACE to abort autoboot in 2 seconds
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
reading boot.scr
** Unable to read file boot.scr **
reading uEnv.txt
473 bytes read in 4 ms (115.2 KiB/s)
Loaded env from uEnv.txt
Importing environment from mmc0 ...
" (type: i)lags type check failure for "ipaddr" <= "192.168.7.3
" into hash tableinsert "ipaddr=192.168.7.3
" (type: i)lags type check failure for "serverip" <= "192.168.7.4
" into hash tableinsert "serverip=192.168.7.4
Running uenvcmd ...
Booting from network ...
link up on port 0, speed 100, full duplex
*** ERROR: `serverip' not set
link up on port 0, speed 100, full duplex
*** ERROR: `serverip' not set
Wrong Image Format for bootm command
ERROR: can't get kernel image!
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
** File not found /boot/zImage **
switch to partitions #0, OK
mmc1(part 0) is current device
Scanning mmc 1:1...
switch to partitions #0, OK
mmc1(part 0) is current device
SD/MMC found on device 1
** Invalid partition 2 **
## Error: "bootcmd_nand0" not defined
starting USB...
USB0: Port not available.
link up on port 0, speed 100, full duplex
BOOTP broadcast 1
data abort
pc : [<9ff8742e>] lr : [<00001c40>]
reloc pc : [<8083542e>] lr : [<e08afc40>]
sp : 9df318e0 ip : 00000000 fp : 9ffece48
r10: 9ffec990 r9 : 9df31ed8 r8 : 0000000e
r7 : 9ffeecd4 r6 : 9ffeecdc r5 : 00000000 r4 : 9ffece8e
r3 : 00060101 r2 : 00000008 r1 : 9ffece4e r0 : 0000000e
Flags: nzCv IRQs off FIQs on Mode SVC_32
Resetting CPU ...
resetting ...
Kindly help.
Thank you.
lear...@gmail.com
Oct 23, 2019, 10:58:02 AM10/23/19
to BeagleBoard
Hi,
From which device are you trying to boot u-boot.
Is it emmc or the sdhc card??
From your console output:
> reading uEnv.txt
> 473 bytes read in 4 ms (115.2 KiB/s)
> Loaded env from uEnv.txt
> Importing environment from mmc0 ...
> " (type: i)lags type check failure for "ipaddr" <= "192.168.7.3
Your settings seemed to be getting overwritten by other settings (could be in the other bootable device).
You could probably try the following:
1.Stop the u-boot boot process at the count down .
2.At the u-boot shell, create new or update env variables with your desired values.
3.Save these environment variables.
4.Restart the board.
5.Linux could be loaded through NFS boot.
Regards,
Adarsh.
jennifer Dsilva
Dec 3, 2019, 3:29:07 AM12/3/19
to BeagleBoard
Hi,
I changed the uEnv.txt file. It is working now.
Thank you
Reply all
Reply to author
Forward
0 new messages