Eagle questions
5 views
Skip to first unread message
Todd Blatt
Jan 7, 2013, 10:25:03 PM1/7/13
to baltimore-node-discussion
I'm working on a project and need some help with Eagle. Does anyone have time and experience with it?
Todd Blatt
tbl...@gmail.com
@tblatt on twitter
443-599-9196
Todd Blatt
tbl...@gmail.com
@tblatt on twitter
443-599-9196
READ CAREFULLY. By reading this email, you agree, on behalf of your
employer, to release me from all obligations and waivers arising from
any and all NON-NEGOTIATED agreements, licenses, terms-of-service,
shrinkwrap, clickwrap, browsewrap, confidentiality, non-disclosure,
non-compete and acceptable use policies ("BOGUS AGREEMENTS") that I
have entered into with your employer, its partners, licensors, agents
and assigns, in perpetuity, without prejudice to my ongoing rights and
privileges. You further represent that you have the authority to
release me from any BOGUS AGREEMENTS on behalf of your employer.
employer, to release me from all obligations and waivers arising from
any and all NON-NEGOTIATED agreements, licenses, terms-of-service,
shrinkwrap, clickwrap, browsewrap, confidentiality, non-disclosure,
non-compete and acceptable use policies ("BOGUS AGREEMENTS") that I
have entered into with your employer, its partners, licensors, agents
and assigns, in perpetuity, without prejudice to my ongoing rights and
privileges. You further represent that you have the authority to
release me from any BOGUS AGREEMENTS on behalf of your employer.
Luke Orland
Jan 7, 2013, 10:27:14 PM1/7/13
to Baltimore Node
Used it a lot a few years ago. I might be able to answer some questions.
--
You received this message because you are subscribed to the Google Groups "baltimore-node-discussion" group.
To post to this group, send email to baltimore-no...@googlegroups.com.
To unsubscribe from this group, send email to baltimore-node-dis...@googlegroups.com.
For more options, visit https://groups.google.com/groups/opt_out.
Todd Blatt
Jan 7, 2013, 10:32:56 PM1/7/13
to baltimore-node-discussion
I'm trying to make a custom milled board that I want to look a certain way. I want most of the board to be milled away so the white fiberglass shows, leaving only certain small regions as copper.
Todd Blatt
tbl...@gmail.com
@tblatt on twitter
443-599-9196
READ CAREFULLY. By reading this email, you agree, on behalf of your
employer, to release me from all obligations and waivers arising from
any and all NON-NEGOTIATED agreements, licenses, terms-of-service,
shrinkwrap, clickwrap, browsewrap, confidentiality, non-disclosure,
non-compete and acceptable use policies ("BOGUS AGREEMENTS") that I
have entered into with your employer, its partners, licensors, agents
and assigns, in perpetuity, without prejudice to my ongoing rights and
privileges. You further represent that you have the authority to
release me from any BOGUS AGREEMENTS on behalf of your employer.
employer, to release me from all obligations and waivers arising from
any and all NON-NEGOTIATED agreements, licenses, terms-of-service,
shrinkwrap, clickwrap, browsewrap, confidentiality, non-disclosure,
non-compete and acceptable use policies ("BOGUS AGREEMENTS") that I
have entered into with your employer, its partners, licensors, agents
and assigns, in perpetuity, without prejudice to my ongoing rights and
privileges. You further represent that you have the authority to
release me from any BOGUS AGREEMENTS on behalf of your employer.
Blaze Sanders
Jan 8, 2013, 9:56:09 AM1/8/13
to baltimore-no...@googlegroups.com
Hello Todd,
I designed the Gravity Development Board using Eagle
Page 148 of the following manual should help
"The board outline can be drawn as a simple narrow line in layer 20, Dimension with the WIRE command. It's easily possible to draw round outlines, too. Therefore use the CIRCLE
command with a small width near 0. You can also place a board contour from a library (such as 19inch.lbr) with"
Chapter 10 Appendix 10.1 Layers and their Usage defines all the layers
Thanks and 73,
Skype blaze.sanders or (202) 657.6569
~ Blaze D. Sanders
MSE Electrical and Computer Engineering
Cell (443) 902-2382Skype blaze.sanders or (202) 657.6569
Office (410) 889-0846
Reply all
Reply to author
Forward
0 new messages