How to access AV Channel without Remote?
Rob
Universal Remote but that won't work either. I now think that the problem is
not with the remote but with the remote signal in the TV or whatever you
call it. Would this be expensive to fix? The main problem however is that
without the remote I can't access the AV function. Is there a way around
this? Thanks for any help.
eltan
the TV if u still have it.
Also u might be able to buy a genuine remote from Speedy Spares in
Melbourne.
Also, it might be a good idea to post the model of the tv and the universal
remote.
"Rob" <adsl...@tpg.com.au> wrote in message
news:40dc4174$1...@dnews.tpgi.com.au...
Rob
news:40dc...@news.comindico.com.au...
> Try the Ch up/dn button on the TV till u get to AV, else read the manual
for
> the TV if u still have it.
It won't go to AV by moving through the channels - that's the problem. The
TV model is CT-2167AT S2 and the Universal Remote is Plustron URC11C-8A. My
guess is that the sensor on the TV is not working any more. Regards
eltan
ie, eg make channel 1 an AV chennel.
"Rob" <adsl...@tpg.com.au> wrote in message
news:40dc...@dnews.tpgi.com.au...
The Real Andy
I had an akai hooked up to a PACE optical inspection station. The same
problem occoured and it wasn't the remote. I pulled the tv apart and
found a few spots on the switch pcb up the front where buttons had not
been fitted. I noticed that one of the spots read 'AV'. I soldered a
button in, cut out the little hole in the decal and voila, i had an AV
switch. I don't know if your model has that option available. I also
soldered in the other blank switches and they gave me full control
over colour/brigh etc.
Rob
with it any more.
Regards
"The Real Andy" <.pearson@wayit_dot_com_dot_au_remove_the_obvious_to_reply>
wrote in message news:v46td0t74iam7st55...@4ax.com...
Allan
The problem is Akai had several Chassis and everyone uses a different
Remote...
Its a royal pain,
I have tried several programmable ones, and none seem to work. Also you
cannot buy the original any more.
Time to buy a new TV..:<
Allan
Bill Bailley
>
> The problem is Akai had several Chassis and everyone uses a different
> Remote...
> Its a royal pain,
> I have tried several programmable ones, and none seem to work. Also you
> cannot buy the original any more.
> Time to buy a new TV..:<
>
> Allan
>
>
receivers on TV, Video and Stereo are completely overwhelmed by switched IR
from low energy lamps. This has caught me more than once. Turn them off and
problem gone. Tell me "go blow" if you have covered this.
Luck,
Bill.
Allan
"Bill Bailley" <JustMe@Home> wrote in message
news:40e2c35d$0$18668$afc3...@news.optusnet.com.au...
What I was tiring to say was Akai are a bugger to get a new remotes for,
The pre-programmed units, which suit a heap of brands, just wont work with a
number of akai TV Sets, and even if you get one that says it is for model
XYZ, it wont work.. because you also have to quote the Serial number of the
Set when ordering it from the suplier....
Yobbeaux
"The Real Andy" <.pearson@wayit_dot_com_dot_au_remove_the_obvious_to_reply>
wrote in message news:v46td0t74iam7st55...@4ax.com...
> problem occoured and it wasn't the remote. I pulled the tv apart and
> found a few spots on the switch pcb up the front where buttons had not
> been fitted. I noticed that one of the spots read 'AV'. I soldered a
> button in, cut out the little hole in the decal and voila, i had an AV
> switch. I don't know if your model has that option available. I also
> soldered in the other blank switches and they gave me full control
> over colour/brigh etc.
>