KZM-A9-Dual android 4.0.3でのネットワーク接続
335 views
Skip to first unread message
maine
Apr 30, 2012, 10:57:18 AM4/30/12
to android-emb...@googlegroups.com
maineと申します.
以下のサイトを参考にice cream sandwichをボード上で動かす事ができましたが,ネットにつながりません．
【KZM-A9-DualボードでAndroid 4.0.3(Ice Cream Sandwich)を動かす：http://blog.kmckk.com/archives/4075163.html】
また，NFSサーバからブートしています．
Android 2.3では，ネットに接続できたのですが,Android 4.0.3ではできません.
また，init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' というlogがどうして出るのかが分かりません．
どなたかご教示頂けないでしょうか．
宜しくお願いします.
***********************boot log************************
U-Boot 2009.03-rc1 (Oct 18 2011 - 14:43:52)
Booted Device: NOR Flash
Board: EM/EV ES3 (Rev.ffffff30)
Core: 1.15v
DRAM: 512 MB
Flash: 64 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
DRIVER_VERSION : 110, DATECODE : 080408
LAN9x18 (0x92210000) detected.
Read mac address: 00:01:9B:04:03:B3
start Auto negotiation... (take ~2sec)
Auto negotiation complete, 100BaseTX, full duplex
File transfer via NFS from server 192.168.11.50; our IP address is 192.168.11.53
Filename '/export/android/boot/uImage'.
Load address: 0x40007fc0
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###########################
done
Bytes transferred = 4128768 (3f0000 hex)
## Booting kernel from Legacy Image at 40007fc0 ...
Image Name: Linux-2.6.35.7
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4128704 Bytes = 3.9 MB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.35.7 (maine@maine-desktop-hp) (gcc version 4.4.3 (GCC) ) #1 SMP PREEMPT Sun Apr 29 15:51:27 JST 2012
[ 0.000000] CPU: ARMv7 Processor [411fc093] revision 3 (ARMv7), cr=10c57c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: KZM9D
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] On node 0 totalpages: 42752
[ 0.000000] free_area_init_node: node 0, pgdat c03ddf20, node_mem_map c049f000
[ 0.000000] Normal zone: 334 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 42418 pages, LIFO batch:7
[ 0.000000] On node 1 totalpages: 65536
[ 0.000000] free_area_init_node: node 1, pgdat c03de5a0, node_mem_map d0002000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65024 pages, LIFO batch:15
[ 0.000000] On node 2 totalpages: 0
[ 0.000000] free_area_init_node: node 2, pgdat c03dec20, node_mem_map c05f8000
[ 0.000000] Normal zone: 1 pages exceeds realsize 0
[ 0.000000] On node 3 totalpages: 0
[ 0.000000] free_area_init_node: node 3, pgdat c03df2a0, node_mem_map c0600060
[ 0.000000] Normal zone: 1 pages exceeds realsize 0
[ 0.000000] PERCPU: Embedded 6 pages/cpu @c0609000 s3872 r8192 d12512 u65536
[ 0.000000] pcpu-alloc: s3872 r8192 d12512 u65536 alloc=16*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 2 zonelists in Zone order, mobility grouping on. Total pages: 107442
[ 0.000000] Kernel command line: ip=dhcp noinitrd init=/init root=/dev/nfs console=ttyS1,115200n8n mem=167M@0x40000000 mem=256M@0x50000000 debug no_console_suspend=1 rw nfsroot=192.168.11.50:/export/android/ice04-1,timeo=30 ip=192.168.11.53:192.168.11.50::::eth0:off
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 167MB 256MB = 423MB total
[ 0.000000] Memory: 424496k/424496k available, 8656k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xe0800000 - 0xf0000000 ( 248 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0025000 ( 116 kB)
[ 0.000000] .text : 0xc0025000 - 0xc03b7000 (3656 kB)
[ 0.000000] .data : 0xc03ce000 - 0xc03f7fc0 ( 168 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:374
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 1061.68 BogoMIPS (lpj=5308416)
[ 0.260000] pid_max: default: 32768 minimum: 301
[ 0.260000] Mount-cache hash table entries: 512
[ 0.260000] Initializing cgroup subsys cpuacct
[ 0.260000] Initializing cgroup subsys freezer
[ 0.260000] CPU: Testing write buffer coherency: ok
[ 0.280000] CPU1: Booted secondary processor
[ 0.540000] Brought up 2 CPUs
[ 0.540000] SMP: Total of 2 processors activated (2123.36 BogoMIPS).
[ 0.540000] NET: Registered protocol family 16
[ 0.540000] L310 cache controller enabled
[ 0.540000] l2x0: 8 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x40440000
[ 0.540000] chip revision ffffff30
[ 0.550000] bio: create slab <bio-0> at 0
[ 0.550000] SCSI subsystem initialized
[ 0.550000] usbcore: registered new interface driver usbfs
[ 0.550000] usbcore: registered new interface driver hub
[ 0.550000] usbcore: registered new device driver usb
[ 0.550000] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.550000] Switching to clocksource sti
[ 0.560000] NET: Registered protocol family 2
[ 0.560000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.560000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.560000] TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
[ 0.560000] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.560000] TCP reno registered
[ 0.560000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.560000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.560000] NET: Registered protocol family 1
[ 0.580000] RPC: Registered udp transport module.
[ 0.580000] RPC: Registered tcp transport module.
[ 0.580000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.580000] PMU: registered new PMU device of type 0
[ 0.580000] Power Management for EMXX.
[ 0.580000] spi: registered device spi [spi]
[ 0.580000] Starting pmu...
[ 0.580000] ashmem: initialized
[ 0.600000] yaffs built Apr 29 2012 15:51:18 Installing.
[ 0.600000] msgmni has been set to 829
[ 0.600000] io scheduler noop registered
[ 0.600000] io scheduler deadline registered (default)
[ 0.600000] io scheduler cfq registered
[ 0.610000] emxx_fb: registered device fb
[ 0.610000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.610000] serial8250.0: ttyS0 at MMIO 0xe1020000 (irq = 40) is a TI16750
[ 0.610000] serial8250.0: ttyS1 at MMIO 0xe1030000 (irq = 41) is a TI16750
[ 1.120000] console [ttyS1] enabled
[ 1.120000] loop: module loaded
[ 1.120000] i2c /dev entries driver
[ 1.130000] Linux video capture interface: v2.00
[ 1.140000] emxx_v4l2: registered device video0 [v4l2]
[ 1.140000] PPP generic driver version 2.4.2
[ 1.140000] PPP Deflate Compression module registered
[ 1.150000] PPP BSD Compression module registered
[ 1.150000] smsc911x: Driver version 2008-10-21.
[ 1.160000] smsc911x-mdio: probed
[ 1.160000] eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)
[ 1.170000] net eth0: MAC Address: 00:01:9b:04:03:b3
[ 1.180000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.180000] emxx-ehci-driver emxx-ehci-driver: EMXX EHCI
[ 1.190000] emxx-ehci-driver emxx-ehci-driver: new USB bus registered, assigned bus number 1
[ 1.200000] emxx-ehci-driver emxx-ehci-driver: irq 115, io mem 0xe2701000
[ 1.220000] emxx-ehci-driver emxx-ehci-driver: USB 2.0 started, EHCI 1.00
[ 1.220000] hub 1-0:1.0: USB hub found
[ 1.230000] hub 1-0:1.0: 1 port detected
[ 1.240000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.240000] emxx-ohci-driver emxx-ohci-driver: EMXX OHCI
[ 1.250000] emxx-ohci-driver emxx-ohci-driver: new USB bus registered, assigned bus number 2
[ 1.260000] emxx-ohci-driver emxx-ohci-driver: irq 115, io mem 0xe2700000
[ 1.340000] hub 2-0:1.0: USB hub found
[ 1.350000] hub 2-0:1.0: 1 port detected
[ 1.360000] Initializing USB Mass Storage driver...
[ 1.360000] usbcore: registered new interface driver usb-storage
[ 1.370000] USB Mass Storage support registered.
[ 1.370000] udc: version Apr 29 2012
[ 1.380000] android init
[ 1.380000] android_probe pdata: c03e1970
[ 1.380000] android_bind
[ 1.390000] android_bind_config
[ 1.390000] android_usb gadget: android_usb ready
[ 1.390000] udc: ----- VBUS OFF
[ 1.400000] f_adb init
[ 1.400000] android_register_function adb
[ 1.400000] f_mass_storage init
[ 1.410000] fsg_probe pdev: c03e1708, pdata: c03e1960
[ 1.410000] android_register_function usb_mass_storage
[ 1.420000] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 1.430000] android_usb gadget: Number of LUNs=1
[ 1.430000] lun0: LUN: removable file: (no medium)
[ 1.430000] adb_bind_config
[ 1.440000] input: kzm9d_key as /devices/virtual/input/input0
[ 1.440000] input: kzm9d_touch as /devices/virtual/input/input1
[ 1.450000] using rtc device, rtc8564, for alarms
[ 1.460000] emxx-rtc 0-0051: rtc core: registered rtc8564 as rtc0
[ 1.460000] Battery probe...
[ 1.470000] Starting wdt.
[ 1.470000] usbcore: registered new interface driver usbhid
[ 1.480000] usbhid: USB HID core driver
[ 1.480000] logger: created 64K log 'log_main'
[ 1.480000] logger: created 256K log 'log_events'
[ 1.490000] logger: created 64K log 'log_radio'
[ 1.500000] logger: created 64K log 'log_system'
[ 1.500000] Starting sound codec.
[ 1.510000] ALSA device list:
[ 1.510000] #0: sound codec (emxx mixer)
[ 1.510000] TCP cubic registered
[ 1.520000] NET: Registered protocol family 17
[ 1.520000] Registered led device: led1
[ 1.530000] Registered led device: led2
[ 1.530000] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 1
[ 1.540000] emxx-rtc 0-0051: setting system clock to 2000-01-01 00:07:54 UTC (946685274)
[ 1.610000] mmc0: new high speed MMC card at address 0001
[ 1.610000] mmcblk0: mmc0:0001 3.83 GiB
[ 1.620000] mmcblk0: p1 p2 p3
[ 2.080000] net eth0: SMSC911x/921x identified at 0xe0820000, IRQ: 167
[ 3.090000] IP-Config: Guessing netmask 255.255.255.0
[ 3.090000] IP-Config: Complete:
[ 3.090000] device=eth0, addr=192.168.11.53, mask=255.255.255.0, gw=255.255.255.255,
[ 3.100000] host=192.168.11.53, domain=, nis-domain=(none),
[ 3.110000] bootserver=192.168.11.50, rootserver=192.168.11.50, rootpath=
[ 3.120000] Looking up port of RPC 100003/2 on 192.168.11.50
[ 5.130000] Looking up port of RPC 100005/1 on 192.168.11.50
[ 5.150000] VFS: Mounted root (nfs filesystem) on device 0:12.
[ 5.160000] Freeing init memory: 116K
[ 6.880000] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
[ 7.130000] enabling adb
[ 7.130000] adb_open
sh: can't access tty; job control turned off
$ [ 7.620000] warning: `rild' uses 32-bit capabilities (legacy support in use)
[ 32.220000] request_suspend_state: wakeup (3->0) at 32231564643 (2000-01-01 00:08:25.177713413 UTC)
[ 190.070000] request_suspend_state: sleep (0->3) at 190079979927 (2000-01-01 00:11:03.026128697 UTC)
[ 190.130000] PM: Syncing filesystems ... done.
[ 190.130000] Freezing user space processes ... (elapsed 0.02 seconds) done.
[ 190.170000] Freezing remaining freezable tasks ... (elapsed 0.02 seconds) done.
[ 190.200000] PM: suspend of devices complete after 1.341 msecs
[ 190.210000] PM: late suspend of devices complete after 0.274 msecs
[ 190.210000] Disabling non-boot CPUs ...
[ 190.310000] CPU1: shutdown
[ 190.310000] Enabling non-boot CPUs ...
[ 190.320000] CPU1: Booted secondary processor
[ 190.620000] CPU1 is up
[ 190.620000] PM: early resume of devices complete after 0.091 msecs
[ 190.630000] wakeup wake lock: alarm_rtc
mizmit1222
May 7, 2012, 1:30:13 AM5/7/12
to Android-Embedded-Japan
みずの＠組み込みWGです。
カーネルはeth0を見つけているのでnetcfgコマンドで
なんとかなるんじゃないでしょうか。
init: cannot find '/system/etc/install-recovery.sh'
というメッセージは無視しても構いません。
ではでは。
カーネルはeth0を見つけているのでnetcfgコマンドで
なんとかなるんじゃないでしょうか。
init: cannot find '/system/etc/install-recovery.sh'
というメッセージは無視しても構いません。
ではでは。
maine
May 7, 2012, 2:25:18 AM5/7/12
to android-emb...@googlegroups.com
みずの＠組み込みWG様、返信ありがとうございました．
早速，netcfgコマンドで以下を実行してみましたが，ネットに接続出来ません.
# netcfg
lo UP 127.0.0.1/8 0x00000049 00:00:00:00:00:00
eth0 UP 192.168.11.53/24 0x00001043 00:01:9b:04:03:b3
# setprop net.eth0.dns1 8.8.8.8
他にも何か対処法ありましたら,ご教示頂ければと思います．
よろしくお願い致します.
maine
May 7, 2012, 2:51:37 AM5/7/12
to android-emb...@googlegroups.com
みずの＠組み込みWG様
# netcfg eth0 up
# netcfg eth0 dhcp
することで,ネット接続できました．
今後ともよろしくお願いします.
ありがとうございました．
Reply all
Reply to author
Forward
0 new messages