Clone or copy failing hard Disk

[Gordon Darling]

I have a dual core 64 bit Athlon based box running Suse 10.3 with a
failing hard disk. It'll run for 4 to 8 hours then freeze. Reboot and the
disk is missing from the BIOS. Wait 30 minutes for it to cool down and
the disk reappears and then I have to fsck the disk. The box is still
under rtb warranty but the supplier is sending me a replacement disk on a
swap basis.

I've managed to back up the important stuff to DVD (/home /etc and so on)
but the ideal solution would be to try and clone the disk or copy
everything with permissions, symlinks, etc (xxcopy?) if I can before it
fails totally.

Suggestions on best route to take when the replacement drive arrives.
Failing drive is SATA 250GB Hitachi partioned as
/dev/sda1 on /
/dev/sda2 on swap
/dev/sda6 on /home
/dev/sda5 on /usr
/dev/sda7 on /var

Replacement is 250Gb SATA Seagate

Regards
Gordon

[Gordon Darling]

Further to above I've downloaded and burned g4l (Ghost for Linux) which
apparently does "click-n-burn".

However, I'll have to edit fstab as SuSE use disk-by-id

as in existing fstab

/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFA100R112282Kpart1 /
/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFA100R112282K-part6 /home
/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFA100R112282K-part5 /usr
/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFA100R112282K-part7 /var
/dev/disk/by-id/scsi-SATA_Hitachi_HDT7250_VFA100R112282K-part2 swap

Can I get away with editing it to/dev/sda1 / , etc or how do I obtain the
disk-id for the new disk.

Regards
Gordon

[Don Raboud]

Gordon Darling wrote:

New disk is the same size as the failing one I presume?

If the failing drive is /dev/sda and the new dirve is /dev/sbd, try

dd if=/dev/sda of=/dev/sdb bs=8M conv=noerror

This will make an exact copy of the disk (including all partition
information) subject to reading errors. The conv=noerror tells dd to
continue if read errors are encountered.

You could also set up the partitions on the new disk before hand and use dd
once for each partition separately, like

dd if=/dev/sda1 of=/dev/sdb1 bs=8M conv=noerror
dd if=/dev/sda2 of=/dev/sdb2 bs=8M conv=noerror
...

Good luck.
--
Don

[ray]

I believe you'll also need conv=sync - noerror keeps it going past
errors; sync replaces bad blocks with nulls - otherwise data gets
scrambled, at least that was my experience in backing up partitions to a
file.

[ray]

On Wed, 30 Jan 2008 08:25:41 -0600, Gordon Darling wrote:

FWIW - Not too long ago I replace a 40gb disk in my laptop with a 120gb.
I backed everything to an external USB drive using partimage from a Live
CD - then swapped drives and restored them.

[steve]

On Wed, 30 Jan 2008 22:49:47 +0800, Gordon Darling wrote
(in article <neydnYGMfIYWEz3a...@pipex.net>):

I presume you have extra cooling on your hard disk right?

Steve