There MUST be a trick to installing spline in patio screen panel...

[ismail.c...@gmail.com]

I have a screened-in breezeway between our house and detached garage,
and our small children (and their many friend :) ) kept pushing on the
screen door's lower panel, instead of against the frame, until the top
tore clean out.
Taking out the existing spline and screen material wasn't too much
trouble. I cut (a little over-sized since this is my first attempt) a
24x30 panel from a roll of new screen. I found it nearly impossible to
push in both the screen and spline at the same time, as instructed.
I found the first trick, which seems to be to roll in the screen by
itself first, and then try to roll in the spline. However, it still
takes a lot of effort to push it in, and I'm tearing edge of the
screen as I do it, which defeates the purpose of the repair.
Could anyone tell me if there is an additional trick to getting the
(solid/flat D-shaped) spline in the groove without destroying the
screen, or describe in exhaustive and graphic details how it should be
done?
Thanks much for any pointer,

Ismail

[Tony Hwang]

Hi,
Spline and roller has to be proper size for the job. There is heavy duty
screen material(fiberglass) which is good for small dogs/cats which I
use on my screen door.

[Robert Allison]

ismail.c...@gmail.com wrote:

I always put a little soapy water on it and it slides right in.

--
Robert Allison
Rimshot, Inc.
Georgetown, TX

[Al Bundy]

ismail.c...@gmail.com wrote in news:1181790650.824938.265560
@q19g2000prn.googlegroups.com:

Yea it can be nasty to do. You can get all the way to the last corner,
slip and pop a hole even with a screen tool. Assume you are using one. It
is possible the spline you are using is the wrong diameter assuming you
are putting in new spline, The old spline may be dried out which will
make it less flexible. But of course if you get too narrow a spline it
will push out easy. Ughhh!

Using fiberglass/plastic screening? Easier to work with as far as the
spline pushing it in.

Bottom line is it takes patience, practice, and lots of "Aw-Shit!"s.

[aemeijers]

"Al Bundy" <postm...@127.0.0.1> wrote in message
news:Xns994EF40A...@216.196.97.136...

Well, this falls in the category of stuff I'll pay somebody the 10 or 20
bucks to do, if it is a location that needs to look pretty. I have changed
out screens, but never got the 'taut bedsheet' look of a factory screen. As
to the kid problem- might I recommend adding a horizontal bar at kid height,
to use as a handle? Some nice metal stock, and some standoffs and matching
screws from the parts aisle at the borg, and it wouldn't even be too ugly.

aem sends...

[JimR]

<ismail.c...@gmail.com> wrote in message
news:1181790650.8...@q19g2000prn.googlegroups.com...

Check on your installation tool. There's a cheap version, with a plastic
handle and a roller on either end, which is marginal at best.

Then I found a more heavy-duty tool, with aluminum body, built-in razor
trimmer, and sturdier wheel. With this one, the spline goes in with no
trouble whatsoever.

[Bobbo]

replying to Tony Hwang, Bobbo wrote:

> dragon40 wrote:
>
> Hi,
> Spline and roller has to be proper size for the job. There is heavy duty
> screen material(fiberglass) which is good for small dogs/cats which I
> use on my screen door.

OK if you are doing a pool screen most likely you're using flat spline.
Starting at the top, position screen and hold in place with a couple
pieces of tape. You need a spline tool to set the spline. Using the flat
end, not the grooved end, roll the screen gently into the channel. Take
the spline, rounded edge facing inwards into the channel and using a
screwdriver set the very end of the spline until it holds. Now place six
inches or so of spline into the channel at the lower edge leaving the
upper edge sticking out. Using the grooved end of spine tool now, roll
along spline exposed at upper edge until it seats into the channel. Be
careful to not cut the screen at the lower edge with tool. Repeat for
sides and then bottom last. Done!

--

[sean....@gmail.com]

On Saturday, March 12, 2016 at 11:44:05 PM UTC-5, Bobbo wrote:
> >
>
> OK if you are doing a pool screen most likely you're using flat spline.
> Starting at the top, position screen and hold in place with a couple
> pieces of tape. You need a spline tool to set the spline. Using the flat
> end, not the grooved end, roll the screen gently into the channel. Take
> the spline, rounded edge facing inwards into the channel and using a
> screwdriver set the very end of the spline until it holds. Now place six
> inches or so of spline into the channel at the lower edge leaving the
> upper edge sticking out. Using the grooved end of spine tool now, roll
> along spline exposed at upper edge until it seats into the channel. Be
> careful to not cut the screen at the lower edge with tool. Repeat for
> sides and then bottom last. Done!
>
> --

I am getting ready to do this myself this weekend and have a quick question to clarify... You said that the rounded edge of the spline "facing inwards into the channel". So, put the rounded edge in first, got it... does it matter which way the rounded edge goes in? In other words, should the rounded edge face the inner edge of the screen or the outer edge (where trimming the excess will take place), or does it not matter?

[gfre...@aol.com]

The pros put the spline in with the rounded edge out. They start and
end up in the same spot, going around the screen. It is a trick tho.

[TJ]

replying to Bobbo, TJ wrote:
rounded edge is up not down...............

--
for full context, visit https://www.homeownershub.com/maintenance/there-must-be-a-trick-to-installing-spline-in-patio-screen-p-225190-.htm

[Oren]

On Mon, 05 Feb 2018 22:14:02 GMT, TJ
<caedfaa9ed1216d60ef...@example.com> wrote:


>rounded edge is up not down...............

What do they do down under in OZ?

[gfre...@aol.com]

They lay the spline in the same way, they just go clockwise around the
screen when they roll it in.