getting drywall to 2nd floor without a boom truck
Tony Miklos
2'x8' bay of the gable end wall. Is there a fairly easy way to do this?
It has to go up about 10.5'. Getting a boom truck will be tricky, no
one wants to do it.
I have a drywall lift for installing drywall but I don't think it will
go high enough. May have access to scaffolding... thinking of making
steps across 2 sets of scaffolding. The scaffolding may be coming here
anyway to do some stucco work. Any creative ideas?
RicodJour
How much drywall are you talking about? The
possible...errr....sensible solutions are dependent on how many sheets
need to go up.
I work by myself a lot and I have a half ton chain hoist that can lift
10'. I've used that to bring up plywood and such, but never drywall.
Don't see why it wouldn't work if you were careful about the sheet
edges.
R
jamesgangnc
> On Tue, 16 Aug 2011 09:06:59 -0400, Tony Miklos
> road wheels.
You didn't say what was under the opening. If they can drive the
forklift under there then just pull the sheets in from the opening.
You can get an extension for most drywall lifts. I don't think I'd
put a lift on top of scaffolding but someone has probably done it :-)
Tony Miklos
There will be 26 sheets of 8' 1/2" and 16 12' 1/2"
Tony Miklos
> On Aug 16, 9:06 am, Tony Miklos<Tony.Mik...@gmail.com> wrote:
>>
>> No truck, no real steps, just pull down attic type. I can open up a
>> 2'x8' bay of the gable end wall. Is there a fairly easy way to do this?
>> It has to go up about 10.5'. Getting a boom truck will be tricky, no
>> one wants to do it.
>>
>> I have a drywall lift for installing drywall but I don't think it will
>> go high enough. May have access to scaffolding... thinking of making
>> steps across 2 sets of scaffolding. The scaffolding may be coming here
>> anyway to do some stucco work. Any creative ideas?
>
> How much drywall are you talking about? The
> possible...errr....sensible solutions are dependent on how many sheets
> need to go up.
Tony Miklos
> On Aug 16, 9:29 am, gfretw...@aol.com wrote:
>> On Tue, 16 Aug 2011 09:06:59 -0400, Tony Miklos
>>
>> <Tony.Mik...@gmail.com> wrote:
>>> No truck, no real steps, just pull down attic type. I can open up a
>>> 2'x8' bay of the gable end wall. Is there a fairly easy way to do this?
>>> It has to go up about 10.5'. Getting a boom truck will be tricky, no
>>> one wants to do it.
>>
>>> I have a drywall lift for installing drywall but I don't think it will
>>> go high enough. May have access to scaffolding... thinking of making
>>> steps across 2 sets of scaffolding. The scaffolding may be coming here
>>> anyway to do some stucco work. Any creative ideas?
>>
>> You need a "lull". That is basically a high lift fork truck with off
>> road wheels.
>
> You didn't say what was under the opening. If they can drive the
> forklift under there then just pull the sheets in from the opening.
Under the opening would be a block wall. If it were lifted up with a
forklift outside it could then be pulled sideways inside the building.
There will be 26 sheets of 8' 1/2" and 16 12' 1/2".
Jim Elbrecht
How much and how big? If you only need like 12 sheets of 1/2" 4x8
up there and only one or two will end up full sheets-- then stage it
downstairs- cut it and carry cut sheets up one at a time.
I work alone & that usually works for me. Leave the sheet on the
trailer - cut & carry. Keeps the mess inside down - keeps the stuff
out of the way & I get my exercise in smaller batches.
Jim
Oren
<Tony....@gmail.com> wrote:
> It has to go up about 10.5'. Getting a boom truck will be tricky, no
>one wants to do it.
Half day rental of a forklift. They will deliver the machine for you.
jamesgangnc
>
> - Show quoted text -
Go to your local supplier and tell them you need it delivered to a 2nd
story. And you have an opening. They will use a truck with a
forklift on the back. Make it clear if you expect them to unload at
the top or if you will have guys ready to do that. Make sure there is
a clear good path to under the opening. If it's soft get some osb and
lay it down.
Jim Elbrecht
To me, that begs the question-- is there ever going to be a real
stairway to that space?
The lift is still the easier way to move that much drywall-- but drop
down stairs seem like a temporary way to get to a space you're doing
that much work on.
Jim
Tony Miklos
Just called my closest dealer, an hour or so away. No half days on pick
up and delivery.
Got a quote for a full day.
Rent $353/day, delivery $95, pick up $95, tax ~$54, total $597.
I'll check with my local rental place, I think they have a forklift.
aemeijers
Nobody else asked, so I will- you are finishing (presumably for living
space) an area without a real stairway? Is adding one part of the
project plans? Pull-down steps aren't rated for fire egress from
living(especially sleeping) space in any area I am aware of.
Just sayin'
--
aem sends...
Andy
Andy comments:
If I didn't want to spend the money, and were willing to invest
a half day, I'd nail some 2x4s together to build a two rail ramp,
about 45 deg,
and slide the dry wall up one at a time. Then I'd pull out the nails
and
use the 2x4s for any framing that needed to be done......
That could be done in much less time than would be taken for
the trip to Home Depot (or wherever) to get special equipment and
take it back....
I'm pretty sure that's how they built the pyramids......
Andy in Eureka, Texas
Tony Miklos
I fully understand. There are plans for an outside stairway but it
takes me forever to make decisions, the main one being exactly where to
put the outside door. The room is above my garage and for now it would
just be storage, but I hate to have the room get full of junk and then
try to hang sheetrock, tape and spackle around all the stuff that will
undoubtedly find it's way up there.
Down in the garage is my "man cave" and the girlfriend says she'd like
the upstairs to be her "woman cave". Ha ha ha, right. That will be the
2nd story of my man cave... the wood shop.
Anyway, it will not be much of anything until the outside steps are in.
aemeijers
1 car or 2 car garage? What size are the joists? 10 foot span, they
need to be at least 2x8, IIRC, on 16 centers, to be rated for more than
light storage. In my part of planet, that is rare. If a 2 car garage, I
hope you have a centerline beam, even with 2x10 joists,
Somebody that can do the deflection math in their head will be along
shortly to correct me- I'm no engineer, my 'gut feelings' about these
things, are based on how things were done back in stone age. Engineered
joists never will look right to me, even though my head knows they work
well.
--
aem sends...
Joe
>snip<
> If I didn't want to spend the money, and were willing to invest
> a half day, I'd nail some 2x4s together to build a two rail ramp,
> about 45 deg,
> and slide the dry wall up one at a time. Then I'd pull out the nails
> and
> use the 2x4s for any framing that needed to be done......
>
> That could be done in much less time than would be taken for
> the trip to Home Depot (or wherever) to get special equipment and
> take it back....
>
> I'm pretty sure that's how they built the pyramids......
>
> Andy in Eureka, Texas
BTDT, exactly how we hoisted 30' wide trusses to a second floor
location. Two people, one pushing, one on the header plate, C-clamps
as safety stops on the 45 degree ramps, and a decent length of rope
and ten of the trusses were stacked in place in a couple of hours. In
a nearby development there were three guys working with a boom truck
all morning. They had more $$ to spend, I guess.
Joe
Joe
Tony Miklos
Garage is 28 x 32. Custom built 12/12 pitch roof trusses for attic are
rated for it to be a full live load bearing floor. No beam needed. I'd
have to dig up the specs sheet but there are 2x12's at the floor and
2x8's for the roof with all the truss webbing in between. Attic room is
16' wide. I'm about 220lbs and can make the floor shake but I can't
make it bounce. ......................
Found the blueprints, from what I can decipher the attic room floor is
rated at 40lb/sq'. Just called the truss manufacture to double check,
they will get back to me.
RicodJour
Typically second floors are designed with a 30#/SF live load, so the
40# is a point in your favor, as is the no-bounce test, though that
might change once the room is loaded and occupied. You mentioned
putting a shop up there, right? What sort of shop and what are the
heaviest items?
R
Tony Miklos
A wood shop, nothing too heavy because none of my tools are that good.
:-( Although I would still put the heaviest items along the side walls
and light stuff in the middle of the room.