HELP: weatherstripping - door jamb problem

[Zz Yzx]

My wooden entranceway door jambs have a kerf to accept the
weatherstripping. But the kerf seems too large (1/4") and the
weatherstripping doesn;t stay in place. I haven't seen any
weaterstripping at HD or Lowe's that is made for such a large kerf.

Is there a simple fix? A product?

Thanks a heap,
-Zz

[Joe]

You probably have a commercially made prehung door, perhaps Andersen,
Pella or Thermatrue. It may be a PITA but, talking with a customer
service person at one or all of them might get you the info on where
or how to get weatherstripping that will fit. Alternatively, try a
local lumber yard that caters to contractors. That also may be the
source of the door and may even have repair pieces for the product or
could order them.
You did a Google search, no doubt?

Joe

[Zz Yzx]

>You did a Google search, no doubt?

IDAGS. I always DAGS.

Thanks for the info, Joe.

-Zz

[Jim Elbrecht]

Yzx <zzy...@hotmail.com> wrote:

>My wooden entranceway door jambs have a kerf to accept the
>weatherstripping. But the kerf seems too large (1/4") and the
>weatherstripping doesn;t stay in place. I haven't seen any
>weaterstripping at HD or Lowe's that is made for such a large kerf.

My Peachtree [about 1990 vintage] door was like that. I hit the
right guy at the counter in the *real* lumberyard one day and he ran
upstairs to the back of the warehouse and grabbed some for me.

I got three sets. By the time the cat ruined all of those the
lumberyard was closed and nobody else had them.

Then I got smart and used a few dabs of silicone on the smaller stuff.
I had to use tape to hold it in for a few hours- but it holds fine &
seals well.

Sounds like a PITA- but lookie here-- they have a fix
http://www.allaboutdoors.com/product_info.php?products_id=84248

Jim

[Oren]

On Fri, 20 Nov 2009 08:25:06 -0800, Zz Yzx <zzy...@hotmail.com>
wrote:

Door shops or Glass/glazing shops that build locally might be a
source. At least for some info... ideas.

[Colbyt]

"Zz Yzx" <zzy...@hotmail.com> wrote in message
news:fhgdg5p52ps625ols...@4ax.com...

Other replies seem to indicate that those were in fact made which I did not
know.

Try folding a piece of electrical tape or a 1/2 wide strip of duct tape over
the edge that inserts and see if that doesn't tighten it up enough to make
it stay in place.

I would test in on a small section before I applied it to a whole strip.

Colbyt

[RicodJour]

Glue in a strip of wood to close down the kerf to fit the readily
available kerf gasketing.

R

[Red Green]

RicodJour <rico...@worldemail.com> wrote in news:6e0a39fd-ce5e-4e43-
92a1-4dc...@m35g2000vbi.googlegroups.com:

Should you go that route, a couple of strip options.

Cut the strip off of say a 1x8 on a table saw. Just cut it so the thin
piece you want is on the outside of the blade. Cheapest route and you'll
have plenty of stock for multiple f'ups, errrrr...adjustments.

I saw strips of various types of wood in a hobby shop once. They ranged
from like 1/32 thick and up.

[Zz Yzx]

>> Glue in a strip of wood to close down the kerf to fit the readily
>> available kerf gasketing.
>>
>> R
>>
>
>Should you go that route, a couple of strip options.
>
>Cut the strip off of say a 1x8 on a table saw. Just cut it so the thin
>piece you want is on the outside of the blade. Cheapest route and you'll
>have plenty of stock for multiple f'ups, errrrr...adjustments.
>
>I saw strips of various types of wood in a hobby shop once. They ranged
>from like 1/32 thick and up.

I thought of this option already, but it sounds like a PITA. I've
also discoverede that there are some "wide-kerf" options out there.
More as I learn more.

-Zz

[TJ]

My Pella doors (late '70s) have the same issue, 1/4" wide kerf. After
giving up on finding wide kerf weatherstrip, I came up with the idea
of buying the narrow stuff (Lowe's) and holding it in place with
screen roll or screen spline - the round rubber "cord" that holds your
screens in their frames. I bought .190" diameter, so it's a pretty
snug fit with the weatherstrip. I jammed it in behind the weatherstrip
with a wide putty knive, trying not to stretch it too much as I went.
On the next door I think I'll try the roller tool you use on screens.
Anyway it makes for a nice tight fit, and when the strip is in place
it covers the kerf so you can't see the screen spline.

[Larry]

I gave this same issue with my entry doors. My solution is to use .140” dia window screen repair spline and a screen tool to roll the rubber spline into the kerf with the weather stripping. PITA but it works.

--
For full context, visit https://www.homeownershub.com/maintenance/help-weatherstripping-door-jamb-problem-407617-.htm