Knocking out Drywall
Alan Smithee
of walls down to the studs. Thx
RicodJour
> What's the most efficient way to knock out drywall? I need to demo a couple
> of walls down to the studs. Thx
Poke a hole with a hammer, grab the edges and pull. For the other
side of the wall you can stay on the same of the wall and push/kick the
opposite side drywall.
R
Harry K
Alan Smithee wrote:
> What's the most efficient way to knock out drywall? I need to demo a couple
> of walls down to the studs. Thx
There is no 'neat' way to do it. It is a messy job and the rock is
going to come off in small pieces. Punch a hole and start yanking. If
it was screwed, you are into a slow process of removing them, nails
aren't too bad but it is still tedious. Worst part of the job is the
cleanup.
Harry K
Steve B
"Alan Smithee" <AlanS...@nowhere.com> wrote in message
news:lbsQf.131233$sa3.97895@pd7tw1no...
> What's the most efficient way to knock out drywall? I need to demo a
> couple
> of walls down to the studs. Thx
>
>
Get you some trash cans first thing. And a wheelbarrow.
Make a hole and then make it bigger. Don't do a lot of smashing, as there
are wires and pipes and things in there that you can damage and cause more
work. As the hole gets bigger, it gets easier to see what is holding it on.
Pull nails with a prybar, or take out screws with a screwgun.
Not a clean job, but just TAKE IT SLOW, break up the trash as you go, and
you will be done shortly. A big shop vac helps to keep the dust from going
all over the house.
Steve
EXT
heavy sledge hammers to take out a little drywall. You could rip out live
wires or split open water pipes and damage other things inside the wall. It
is simple, one guy on TV who does it differently just punches a hole between
the studs with his fist and starts pulling down drywall. Most other people
just use a claw hammer to make a small hole and use the claw to pull the
rest off the studs.
"Alan Smithee" <AlanS...@nowhere.com> wrote in message
news:lbsQf.131233$sa3.97895@pd7tw1no...
ameijers
"RicodJour" <rico...@worldemail.com> wrote in message
news:1142052144.1...@i40g2000cwc.googlegroups.com...
Thereputic, but messy. I recommend long vertical Sawzall cuts in the middle
of the stud cavities. You can then rock each section, and take it out in
bigger cleaner chunks. Try not to cut any live wiring or plumbing, if they
are to be reused. If you don't already have one, I recommend investing in a
medium-size Stanley Wonder Bar- the uses will become obvious once you start.
If you want to save the other walls and ceilings in those rooms, don't
forget to slit the inside corners with a sharp utility knife before you
start. Otherwise, the tape is likely to pull off the surface paper on areas
you don't want to damage. Depending on how well the corners and ceiling were
mudded, you may need to surgically remove the mud and tape from the
remaining half of the joint to get a decent mud job once you reskin the
wall.
aem sends...
Steve B
"ameijers" <aeme...@worldnet.att.net> wrote
> Thereputic, but messy. I recommend long vertical Sawzall cuts in the
> middle
> of the stud cavities.
If'n you want to cut something you don't want to cut, go at it with a
SawZall. Better yet, just get a fire axe and put up a few pictures of
in-laws for motivation.
I recommend taking it out in small chunks so you can see around the back and
not pull or cut anything you don't want to.
It comes off fast and easy once you get the first hole. Buy a couple of
flat bars and a cat claw nail puller. After that, just grunt and bear it.
Steve
Alan Smithee
"Steve B" <boozoo...@zydeco.net> wrote in message
news:29HQf.887$wp.234@fed1read12...
