Also parts on parts of my roof the shingle are very hard to pry up and
I cannot get the guard far enough under because there is a nail or
something blocking it - what do you suggest in that situation - cutting
the guard so it's more narrow?
http://img241.imageshack.us/img241/6464/dscf0582uz5.jpg
http://img135.imageshack.us/img135/4590/dscf0583fa1.jpg
"Joe" <joe5...@gmail.com> wrote in message
news:1161951529.6...@h48g2000cwc.googlegroups.com...
Are these the Amerimax ones from Home Depot? I have installed the solid
versions on my roof. The brief instructions on the label should tell how to
bend them.
At least for the solid covers: You need to bend them up just back from the
outer edge, then bend them back down as they near the shingles. This adjusts
them for the roof pitch and allows the outer edge to be horizontal so it will
snap into place. There are pre-scored bending lines but they are still fairly
stiff, fortunately I have a bender long enough to put them in and tweak them.
--
Dennis
Larry
"Joe" <joe5...@gmail.com> wrote in message
news:1161951529.6...@h48g2000cwc.googlegroups.com...
>These look like the amerimax ones. If they are the ones that have the screen
>over them the screen part goes UP. It looks to me like you are installing
>them upside down. Sometimes you will have to cut a slip to make it around a
>nail in the shingle or you will have to cut a little piece out of the bottom
>where it snaps into the gutter around the gutter spike. Good luck. I also
>had to drill small 1/8" holes in them right before the little flat piece
>that sticks up. This was because in heavy rain, the water would just cascade
>right over them. If you want pictures of my modification, let me know.
>
>Larry
>
I just put these on my gutters. Larry is right, you are installing
them upside down. I agree with Larry that the problem may be that you
don't have enough space between the gutter spike and the bottom of the
folded over top of the gutter for the guard to slide in. You can
either slide a screwdriver gently in that area to make a bigger gap,
or trim away a small part of the bottom lip of the guard where the
spikes are.
If they hit a nail when you slide them under the shingles, just trim
them around it.
Once you get one corner started, a big pair of pliers or
channel-locks, held vertically, can be used to convince the guard to
slide onto the gutter.
Once installed, I've found them to work quite well.
Also, if it's cold now in your area, you may find heating the stubbon
shingles with a heat gun will make them more flexible. you don't want
to break them trying to bend them up.
HTH,
Paul
I have some of those kind and they don't lay on the
roof very well. They keep flipping over. I don't
think they are supposed to clip on the gutter, I
think they are supposed to clip on the edge of the
shingles. Any way after my experience that is about
the only way to make them work. Actually I have
bricks laying on the top side to hold them down.
Bill Gill
Strange as that's not my experience. I don't have any labels so I can
not say what they were called or the part number. I attached them to
the "gutter" as described in the instructions, not a problem after 3
years. My residence is near the Chicago area and we do get some wind
here, recently had gusts around 50 MPH, never had one move and they
are free to open on the hinge. Once had a squirrel enter through the
open end and I chased it back-and-forth until he finally lifted up one
length and took off. I tried the flat plastic type that suppose to
slide under the shingles but found shingles stuck to roof that's why I
installed these and have not been sorry.
Don Whynot