98 Chevy Suburban K2500 Cooling system questions
cr
radiator developed a crack in the oil cooler tank right beside the upper oil
cooler fitting. So, it was time to replace the radiator -- and while I was
at it the water pump, thermostat and upper/lower radiator hoses.
Before starting the work, I check the coolant level and it was at the top of
the radiator neck. The coolant resevoir was empty (some coolant lost due to
the leak). When I drained the radiator, I checked the amount of coolant
collected and it was approx 2 gallons. After removing the radiator and the
radiator hoses, I removed the water pump. I then removed the coolant drain
plug on the passenger side of the engine and about 2.5 gallons of coolant
came out.
I then removed the drain plug on the driver side of the engine --- maybe 2
drops of coolant came out. So at this point, I only have 4.5 gallons of
coolant. The capacity of the cooling system is 27.5 qts -- so now I am
wondering where the rest of the coolant is and why didn't any coolant drain
from the driver side of the engine. Some coolant did of course spill on the
ground in the process -- but not that much. Even if 1/2 gallon made it to
the ground, there is still quite a bit of coolant hiding somewhere.
I noticed that the coolant was still pooled at the driver side water pump
port. The passenger side water pump port is empty. I have a picture at :
http://home.tx.rr.com/theroberts/1998%20Chevy%20Suburban%20K2500/ -- just
select the "Radiator work" pdf file. Note: the coolant appears green
because I had previously added some dye which changed the Dexcool color from
red to green.
Questions
-------
- Should there have been coolant draining from BOTH drain plugs ? The GM
service manual just says remove the drain plug -- doesn't even mention (in
the text or diagrams) that there are two.
- Since there is obviously still coolant sitting on one side, does this
basically mean I have a blocked coolant passage ?
I would prefer to remove all the old coolant -- I could put everything back
together and flush with water. But I'm concerned about the coolant not
draining from the one side.
Any ideas or suggestions are greatly appreciated.
Thanks
Old Crow
Take that driver's side plug out again, get a screwdriver and stick up
there and knock the rust loose, and prepare for a green shower. :-)
--
Old Crow "Yol Bolson!"
'82 FLTC-P "Miss Pearl"
'95 YJ Rio Grande
BS#133, SENS, TOMKAT, MAMBM
--
Posted via a free Usenet account from http://www.teranews.com
cr
today trying different wires, screwdrivers, ice pick, etc with no luck. I
could get some really small pieces out but nothing major. It feels very
solid - so apparently it has not been flushed properly in the past. I
purchased the car used with about 98k miles on it.
Not sure how else to get it cleared out without using a drill, etc.
Unfortunately, being on the driver side right above the oil filter, there is
not much room there. I may not have a choice but to put everything back
together and just flush out the old coolant that is left.
Thanks for the help.
"Old Crow" <walli...@yahoo.com> wrote in message
news:l8hnl3dtv4th177oq...@4ax.com...
azwiley1
> I tried that (gently) initially with no success. I spent about an hour
> today trying different wires, screwdrivers, ice pick, etc with no luck. I
> could get some really small pieces out but nothing major. It feels very
> solid - so apparently it has not been flushed properly in the past. I
> purchased the car used with about 98k miles on it.
>
> Not sure how else to get it cleared out without using a drill, etc.
> Unfortunately, being on the driver side right above the oil filter, there is
> not much room there. I may not have a choice but to put everything back
> together and just flush out the old coolant that is left.
>
> Thanks for the help.
>
>
> - Show quoted text -
Pressure washer might work if you have one, or one of those dryer lint
brushes or even a soft brass brush from a gun cleaning kit.
Refinish King
With both plugs out, and a pan underneath. Lift the rear in the center, and
some should come out.
Make sure the thermostat housing is off, and the thermostat out.
You'll never get the whole 27.5 quarts out anyway. That is the capacity as
estimated by the engineers, fully assembled and bone dry.
I hope this helps.
RK
"cr" <c...@tx.rr.com> wrote in message
news:475b7810$0$9582$4c36...@roadrunner.com...