disk replaced / bay disappeared

[Stefan Sieber]

Hi,

I'm running Alt-F on my DNS-323. Since my left HD showed errors, I ejected it and did load the new (via the web interface). However, since that the left bay/disk is not shown in the web interface. The logs do not report errors.

What do I need to do to get bay and the new disk back?

Brgds,
Stefan

[Joao Cardoso]

What hard rev level do you have?
On my B1 board I never saw such behaviour.
Could it be that the errors was not on the disk, but on the disk interface (box hardware)? Can you try the disk with errors on another computer (or in the other box bay?)

Anyhow I need the kernel log (dmesg) shortly after a reboot or power up.

--
You received this message because you are subscribed to the Google Groups "Alt-F" group.
To post to this group, send email to al...@googlegroups.com.
To unsubscribe from this group, send email to alt-f+un...@googlegroups.com.
Visit this group at http://groups.google.com/group/alt-f?hl=en.
To view this discussion on the web visit https://groups.google.com/d/msg/alt-f/-/z5s5Yfh7CzgJ.
 
 

[Stefan Sieber]

Here you go. Thanks.

Linux version 2.6.35.14 (jcard@silver) (gcc version 4.3.3 (GCC) ) #1 Tue Feb 21 15:39:06 WET 2012
CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177
CPU: VIVT data cache, VIVT instruction cache
Machine: D-Link DNS-323
Clearing invalid memory bank 0KB@0xffffffff
Clearing invalid memory bank 0KB@0xffffffff
Clearing invalid memory bank 0KB@0xffffffff
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x41000403
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 16384
free_area_init_node: node 0, pgdat c02ff55c, node_mem_map c0310000
  Normal zone: 128 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 16256 pages, LIFO batch:3
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 55596k/55596k available, 9940k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
    vmalloc : 0xc4800000 - 0xfd800000   ( 912 MB)
    lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc0026000   ( 120 kB)
      .text : 0xc0026000 - 0xc02d2000   (2736 kB)
      .data : 0xc02ea000 - 0xc02ffb80   (  87 kB)
NR_IRQS:64
Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976)
pid_max: default: 4096 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Orion ID: MV88F5181-Rev-B1. TCLK=166666667.
DNS-323: Identified HW revision A1
DNS-323: Found ethernet MAC address: 00:19:5b:ee:2c:6b.
Applying Orion-1/Orion-NAS PCIe config read transaction workaround
pci 0000:00:00.0: reg 10: [mem 0xf1000000-0xf10fffff 64bit pref]
pci 0000:00:00.0: reg 18: [mem 0x00000000-0x03ffffff]
pci 0000:00:01.0: reg 10: [mem 0x40000000-0x400fffff 64bit]
pci 0000:00:01.0: reg 18: [io  0xf0000000-0xf00000ff]
PCI: bus0: Fast back to back transfers disabled
pci 0000:01:00.0: reg 10: [mem 0x00000000-0x03ffffff 64bit pref]
pci 0000:01:00.0: reg 18: [mem 0x10000000-0x1fffffff 64bit pref]
pci 0000:01:00.0: reg 20: [mem 0xf1000000-0xf10fffff 64bit]
pci 0000:01:00.0: reg 30: [mem 0xe0000000-0xe7ffffff pref]
pci 0000:01:00.0: supports D1 D2
pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:01:00.0: PME# disabled
PCI: bus1: Fast back to back transfers enabled
pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe00fffff 64bit]
pci 0000:00:01.0: BAR 0: set to [mem 0xe0000000-0xe00fffff 64bit] (PCI address [0xe0000000-0xe00fffff]
pci 0000:00:01.0: BAR 2: assigned [io  0x1000-0x10ff]
pci 0000:00:01.0: BAR 2: set to [io  0x1000-0x10ff] (PCI address [0x1000-0x10ff]
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
PCI: CLS 32 bytes, default 32
Unpacking initramfs...
Freeing initrd memory: 6240K
squashfs: version 4.0 (2009/01/31) Phillip Lougher
aufs 2-standalone.tree-35-20100809
msgmni has been set to 120
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
console [ttyS0] enabled
loop: module loaded
sata_mv 0000:00:01.0: version 1.28
sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
scsi0 : sata_mv
scsi1 : sata_mv
scsi2 : sata_mv
scsi3 : sata_mv
ata1: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 11
ata2: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 11
ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 11
ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 11
physmap platform flash device: 00800000 at f4000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 5 MTD partitions on "physmap-flash.0":
0x000000000000-0x000000010000 : "MTD1"
0x000000010000-0x000000020000 : "MTD2"
0x000000020000-0x0000001a0000 : "Linux Kernel"
0x0000001a0000-0x0000007d0000 : "File System"
0x0000007d0000-0x000000800000 : "u-boot"
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:19:5b:ee:2c:6b
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
input: gpio-keys as /class/input/input0
i2c /dev entries driver
rtc-m41t80 0-0068: chip found, driver version 0.05
rtc-m41t80 0-0068: rtc core: registered m41t80 as rtc0
lm75 0-0048: hwmon1: sensor 'lm75'
md: linear personality registered for level -1
md: raid1 personality registered for level 1
Registered led device: power:blue
Registered led device: right:amber
Registered led device: left:amber
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
rtc-m41t80 0-0068: setting system clock to 2012-10-14 12:35:52 UTC (1350218152)
ata1: link is slow to respond, please be patient (ready=0)
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: MAXTOR STM3500630AS, 3.AAE, max UDMA/133
ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      MAXTOR STM350063 3.AA PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
Freeing init memory: 120K
aufs test_add:253:mount[57]: uid/gid/perm /tmproot/rootsq 0/0/0777, 0/0/0755
Adding 530108k swap on /dev/sda1.  Priority:1 extents:1 across:530108k
md: bind<sda2>
md/raid1:md0: active with 1 out of 2 mirrors
md0: detected capacity change from 0 to 498221580288
 md0: unknown partition table
eth0: link up, 1000 Mb/s, full duplex, flow control disabled

[Keon91]

Have you tried removing the right working drive from its bay and then plug it into the left bay?

First power down the box before you preform this.

then after you power up the box agian, can you again give the dmesg?

[Stefan Sieber]

I did format it externaly and added it again. Now it is available.

However, no autosync with the first disk.

Thanks,

Stefan

[Keon91]

What do you mean with autosync with the first disk?

RAID1?

Please use the help page in alt-f under RAID (click on the question mark) its all there!