Beninca Wiring Diagram

[Ahmend Studioz]

Manufacturer: Automatismi Beninc SpA.Address: Via Capitello, 45 - 36066 Sandrigo (VI) - ItaliaHerewith declares that: the operator for hinged gates model BOB50M / BOB50ME.is complying with provisions set forth by the following other EC Directive:

• DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004, on the harmonization of the laws of Member States relating to electromagnetic compatibility and which cancels Directive 89/336/EEC, according to the following harmonized regulations: EN 61000-6-2:2005, EN 61000-6-3:2007.
• DIRECTIVE 2006/95/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 12 December 2006, on the harmonization of the laws of Member States relating to electrical equipment designed for use with certain voltage limits, according to the following harmonized regulations: EN 60335-1:2002 + A1:2004 + A11:2004 + A12:2006 + A2:2006 + A13:2008; EN 60335-1-103:2003.

Beninc Luigi, Legal responsible. Sandrigo, 10/06/2010.WARNINGThe product shall not be used for purposes or in ways other than those for which the product is intended for and as described in this manual. Incorrect uses can damage the product and cause injuries and damages.The company shall not be deemed responsible for the non-compliance with a good manufacture technique of gates as well as for any deformation, which might occur during use.Keep this manual for further use. Qualified personnel, in compliance with regulations in force, shall install the system. Packaging must be kept out of reach of children, as it can be hazardous. For disposal, packaging must be divided the various types of waste (e.g. carton board, polystyrene) in compliance with regulations in force. The installer must supply all information on the automatic, manual and emergency operation of the automatic system and supply the end user with instructions for use. An omnipolar switch/section switch with remote contact opening equal to, or higher than 3mm must be provided on the power supply mains.. Make sure that before wiring an adequate differential switch and an overcurrent protection is provided. Pursuant to safety regulations in force, some types of installation require that the gate connection be earthed. During installation, maintenance and repair, cut off power supply before accessing to live parts. Descriptions and figures in this manual are not binding. While leaving the essential characteristics of the product unchanged, the manufacturer reserves the right to modify the same under the technical, design or commercial point of view without necessarily update this manual.Introduction

• Before installing the system, read the instruction herein.
• It is mandatory not to use the BOB 5M / BOB 5ME item for applications different from those indicatedin the instructions herein.
• Supply the end user with instructions for using this system.
• The end user should receive special instruction manual.
• All Beninc items are covered by an insurance policy for damages and injuries caused by manufacture faults. It is however required that the machine bear the CE marking and original Beninc parts be used.

General informationTo ensure a good operation of these automatic devices, the gate to be automated should meet the following requirements:

• good strength and stiffness.
• hinges should have a minimum backlash and allow for smooth and regular manual operations.
• when closed, the gate leaves should correctly overlap for their entire height.

How to install the automatic systemCalculate the height of the system from the ground it is advisable to define a position as much centred as possible with respect to the main door and in correspondence with a strong cross girder). Weld the plate P, following measures in Fig. 1.

• It is advisable to use an electric lock

With the door closed, weld bracket S to a cross beam of the main door or other element with equal strength, according to measures shown in Fig. 1. Keep in mind that, when carrying out this operation, the actuator should not be totally in a stroke end position. Remove the cover C by loosening the screw F. Then fix the actuator to the plate P by means of the screw T and the nut D (Fig. 2). Lock the actuator to plate S by means of screw V and washer R. The holes in the acturator (Fig. 1a-1b) help to keep to the optimum installation measures.

The actuator is provided with adjustable mechanical stoppers in the opening and closing phases. The system is adjusted by suitably positioning the "Open" and "Close" mechanical locks, as shown hereunder (Fig.3):

1. Unlock the automatic system by using the special release lever, as shown in the instructions for the user (page 21-22).
2. Close the door/gate leaf.
3. Loosen screws V1 and move the "Close" lock until it reaches the pivot P, then tighten screws V1.
4. Open the door/gate leaf.
5. Loosen screws V2 and move the "Open" lock until it reaches the pivot P, then tighten screws V2.
6. Reset the automatic operating mode.

In the BOB 5M version, two limit micro-switches are provided fixed to the mechanical stoppers. The micro-switches trigger slightly in advance with respect to the mechanical stop.

1. The special plate P (Fig. 4) allows for using a link for sheath or cable gland PG11, or PG13,5. Once the type of cable gland is applied to the plate, fix the latter to the adaptor cover by means of screws V.
2. Insert the cable, or cables, under the terminal board, as shown in Fig.5. This will leave enough space for the capacitor.
3. BOB 5M: carry out the wiring by referring to the wire diagram shown in Fig 6a (use both limit switches). In order to use either the opening limit switch or the mechanical stoppers, change wiring as shown in Fig. 6b (opening limit switch only) or 6c (mechanical stoppers only).N.B: in wiring connections shown in Fig. 6a and 6b, the capacitor MUST NOT be connected to the control unit, while for wire connection shown in Fig. 6c, the capacitor can be connected to the control unit.
4. BOB 5ME: carry out the wiring by referring to wire diagram shown in Fig 6d.
5. It is mandatory to provide for ground by using the special GND terminal.

1Close2Open3COM4GND5ENCODER signal6ENCODER positive7ENCODER negativeaBlack wirebWhite wirecRed wireFCCCLOSE limit switchFCOOPEN limit switchWARNINGThe insurance policy, which covers any damages or injuries caused by manufacture faults, requires that the installation comply with regulations in force and Beninc original accessories be used.

c80f0f1006