Transistor Datasheet Explained

[Denisha Padley]

TransistorTutorial Includes:

Transistor basics Gain: Hfe, hfe & Beta Transistor specifications Transistor and diode numbering codes Choosing replacement transistors There is a huge number of bipolar transistors available both leaded and surface mount devices. These have been designed to fulfil a variety of different applications in all areas of electronics.

In order to define the parameters of a transistor there are many different specifications that are used. Each of these transistor specifications define an aspect of the performance of the transistor.

Transistor manufacturers issue specification sheets for their transistors which are typically found on the Internet, although years ago engineers used to study data books to find out the information.

For electronic circuit design, selecting the right transistor will need several of the transistor parameters to match the requirements for the circuit. Therefore a variety of the parameters will need to be carefully matched.

Not all the parameters are electrical - aspects such as the size of the package, and whether the device is a surface mount transistor, i.e. surface mount device. With most PCB assembly now using surface mount technology to aid the automated electronics manufacturing of products and equipment, most transistors manufactured these days are SMD transistors.

Whilst most transistors made these days are SMD transistors because of the automated PCB assembly techniques used, there are still many leaded devices as well. Specific transistor part numbers are normally available as leaded versions and also for SMD transistors with the same electrical specifications, although aspects like the heat dissipation will differ because of the different package styles.

The specifications for transistors, like any other electronics component are normally available on the website of the manufacturer. Also electronic component distributors often have details of the specifications of components, or sometimes a link to the specification on the manufacturer's website.

It is also worth noting for electronic components that can be obtained from several manufacturers, that the specifications may vary slightly between manufacturers. For any critical parameters it is wise to use the actual figures from the manufacturer whose product is being used.

Often a second source and further sources may be required to give some level of insurance against a particular supplier or manufacturer ceasing their operation and the part becoming obsolete. In this case the specification parameters for all manufacturers should be closely checked to ensure they meet the requirements for the particular electronic circuit design.

The type number of the device is a unique identifier given to each type of transistor. This enables the full data on its specifications to be checked on the manufacturers transistor datasheet to investigate its performance.

Apart from just giving a standardised type number to the transistors, these schemes can provide information about the transistor performance. The European Pro-Electron scheme is particularly good for this as it distinguishes between different types of transistor, for example a BC109 is a silicon audio frequency low power transistor, and a BFR90 is a low power RF transistor.

However when using automated PCB assembly techniques and surface mount devices, it is found that many transistors are too small to carry the full number that might be used in a data sheet. As a result, a rather arbitrary coding system has developed, whereby the device package carries a simple two or three character identification code.

This can normally be accommodated on the small surface mount diode packages. However, identifying the manufacturers' type number of an SMD diode from the package code may not be easy at first sight. There are some useful SMD codebooks available that provide the data for these devices.

The NPN transistors are more widely used. Like for like they offer better performance than PNP transistors because electrons are the majority carriers and their mobility is higher than that of holes which are the majority carriers in PNP transistors. The basic circuits for NPN transistors also fit well with the negative earth normally used in DC systems.

Although other materials like germanium and gallium arsenide are available, silicon is the most popular because it is cheaper to process and in addition to this, the processes are more advanced than for other materials. As it is used for many other semiconductor devices, there are many benefits of scale and technology available.

This parameter is important because some leakage current will flow between collector and base, causing the part to heat up. Alternatively excessive voltage can damage the collector base junction. As terminal damage can occur to the bipolar transistor, this rating should not be exceeded and ideally the transistor should be run with a good margin in hand.

In operation the collector-base junction is reverse biassed, and a small reverse current will flow (ICBO. As the reverse voltage is increased the electric field in the depletion region of the collector base junction increases, and the reverse current starts to rise as minority carriers gain sufficient energy to generate hole electron pairs which then increase the reverse current. Eventually avalanche breakdown occurs. This limits the maximum voltage that can be applied to the transistor.

VCBO is typically higher than VCEO because with the base terminal of the BJT open, any leakage current will also be the same as externally applied base current, and this is amplified by the transistor. This will cause even more current to flow through the device, heating it up and for this reason, VCEO is often lower than VCBO.

This transistor specification is the maximum voltage that can be placed from the collector to the emitter. It is normally measured with the base open circuit - hence the letter "O" in the abbreviation. During the electronics circuit design stage it is essential to ensure that this value is not be exceeded in operation, otherwise damage may occur. Ideally the transistor should be operated with a good margin in hand.

Often the maximum voltage should only be allowed to rise to 50 or 60% of the maximum value for reliable operation. Note that for circuits using inductors in the collector circuit, the collector voltage may rise to twice the rail voltage.

If the voltage applied between the collector and emitter terminals is high, and increased number of carriers start to diffuse into the collector region from the base. This causes the base emitter diode in the bipolar transistor to start to become forward biassed, and this causes current to flow between the collector and emitter, even though no external base current has been applied. When a certain voltage, VCEO, is reached the transistor can fully turn on, and in some cases this can result in terminal damage to the device.

The collector emitter saturation voltage, i.e. the voltage across the transistor (collector to emitter) when the transistor is turned hard on. It is normally quoted for a particular base and collector current values.

This is the current gain for a transistor expressed as an h parameter or hybrid parameter. The letter "f" indicates that it is a forward transfer characteristic, and the letter "e" indicates it is for a common emitter configuration. The value for hfe is approximately the same as β.

Total power dissipation for the device. It is normally quoted for an ambient external temperature of 25C unless other wise stated. The actual dissipation across the device is the current flowing through the collector multiplied by the voltage across the device itself.

Transistors can be mounted in a variety of packages according to their applications. There are the standard leaded devices that appear in a variety of packages - these packages normally conform to JEDEC standards and start with the letters TO, standing for transistor outline. This is followed by a hyphen and a numeral which is typically up to three digits.

Surface mount transistors, SMD transistors are used in vast quantities because most electronics manufacture and PCB assembly is undertaken using automated techniques and surface mount technology lends itself to this. Popular sizes include the SOT-23 and SOT-223 outlines.

Although it is possible to make many decisions about selecting the right component for a circuit design from the datasheet parameters, this is not the only basis for selecting the right components as there are several other attributes not in the data-sheets that need to be embodied in any decision. These are equally important as the basic specification parameters, but not always taken into account. In our web page, we reveal the key additional aspects to consider so that the overall best choice is made.

There are many different elements to transistor specifications, both both leaded and surface mount transistors. To meet the demand for electronics manufacture there is a huge variety of transistors from which to choose. However it is still relatively easy to choose a transistor when using a basic knowledge of the different transistor specifications and parameters.

Quote: Even more important than the warmth and affection we receive, is the warmth and affection we give. It is by giving warmth and affection, by having a genuine sense of concern for others, in other words through compassion, that we gain the conditions for genuine happiness. Dalai Lama

Thanks for your interest in TI FETs. TI does not specify dead time for our power blocks as this is primarily determined by the external gate drive circuit. We do provide typical switching times in the datasheet as explained in the blog at the link below. Again, these times are highly dependent on the external gate drive circuit.

Thanks again for your interest in TI FETs. I'm including links to an app note and TI FET selection tool below. The app note includes a detailed analysis of sync buck converter losses including common source inductance. The excel-based tool uses the loss equations from the app note and allows the user to compare up to 3 different TI FET solutions based on power loss, package and 1k price. Take a look at the equations tab for the formulas used to calculate the FET losses. There are many other resources available on the web for calculating switching losses. Please contact me if you have any questions.

3a8082e126