Software Radius M1225

[Hollie Brafman]

Hans, once I have the cable where do I find the software? It's beginning to look like getting set up to program this radio will cost more than the radio itself. Unlike Kenwood, where the cable is cheap and the software is free.

Software radius m1225

DOWNLOAD https://t.co/6p2Gb8QIXk

The M1225 is the radio I have been looking at as well. I would love to find out about the programming as well. I take it the CHIRP software won't work from reading your previous comments. Actually, I was looking to buy 2 of these radios, one for the truck, and one for the radio shack. If I like this radio and I'm able to get set up to program it Ok, then I will likely buy more of these for my dads truck and my two son's vehicles as well.

You'll have to find a copy of Motorola RSS for M1225 (not terribly hard to do) but that's definitely not the hard part. RSS doesn't run on modern hardware; for the MT2000 I used Win95's DOS mode on a Pentium without issues. I'm not sure how the M1225 software runs on later computers. Virtualization may be an option but RSS needs Microsoft DOS to work. A 16550-based serial port is highly preferred, I don't know how well the USB ones work; computers of the right vintage for RSS usually have onboard 16550 serial.

More

• All Messages By This Member

displayLikeStats("/g/repeater-builder", 0, 197102344, false) M M $('#timedispmsg197102074').replaceWith(DisplayShortTime(1639084316766098966, false)); #188789
The R1225 repeater, M1225 mobile and P1225 handheld use HVN9054, and Ver 3 and ver 4 is "out there".
Ver 4 was the last and supposedly for XP but I've run it without any problems on XP, 7 and 10 Windows 32-bit.
No version of the HVN9054 will run on 64 bit!

I help take care of a UHF analog trunking system of over 40 channels, around 20 channels use low power
R1225 repeaters. Other sites use dual low power GM300s. All work real well.
Each transmitter is followed by a Henry Electronics model C130AB02B 130w continuous duty amplifier run
at 90 or so watts. Some sites have each transmitter feeding a dual circulator followed by a pass cavity
and individual transmit antennas, other sites have transmitter combiners. All depends on the site.

The system has been TOTALLY reliable - about 15 radios and around 9-10 amplifiers in 30+ years, and
all of the amps were repairable.... swap them out, box them up, send then to Henry, get them back, bench
test them for 1 hour continuous keydown at 100w, shelve them. Done....

Mike WA6ILQ More

• All Messages By This Member

displayLikeStats("/g/repeater-builder", 0, 197102074, false) Craig Ehlers N6YUV $('#timedispmsg197022665').replaceWith(DisplayShortTime(1638970415487725408, false)); #188759
Thank you Steve. What programming software should I use?

Craig More

• All Messages By This Member

displayLikeStats("/g/repeater-builder", 0, 197022665, false) Steve $('#timedispmsg196989928').replaceWith(DisplayShortTime(1638909449705291183, false)); #188749
You should just be able to program those channels with the "shift key" method.
Hold down one of the SHIFT keys for all the numbers, but let up on the period.
So 146.28000 would look like !$^.@*)))
You have to fill all the "trailing Zeros with )
I have done this with M1225's for years.
Those won't do status tone so if you voting method requires that, you will have to use something
like the PTG-10.
Which I have also done with GM300, MAXTRAC, M1225, SM-50, SM120, etc. More

• All Messages By This Member

displayLikeStats("/g/repeater-builder", 1, 196989928, false) Teton Amateur Radio Repeater Association (TARRA) $('#timedispmsg196987018').replaceWith(DisplayShortTime(1638906066637702766, false)); #188744
Hello Craig,

The software runs in Windows, not sure about 10, haven't tried it. But for what you are wanting to know, hold the shift key for the first three numbers, release the shit key for the "." (decimal point) and then shift for the last. Once you have your frequency in, while holding the shift key finish all the way with zeros. For example: shift 146 unshift . shift 52 0 0 0 0 0 unshift (not sure how many zeros you need, just fill it out for the rest).

Mick - W7CAT toggle quoted messageShow quoted text ----- Original Message -----
From: "Craig Ehlers N6YUV"
To: repeater...@groups.io
Sent: Tuesday, December 07, 2021 11:09:49 AM
Subject: [repeater-builder] M1225 VHF programming for Amateur use

We have 8 M1225 VHF radios that we would like to use for voting receivers. Is there a easy way to program them for them for the Amateur Bands.
FCC ID ABZ99FT3038. I do have a DOS computer I have been using for other Motorola radios and also CPS for the later stuff. Any help would really be appreciated.
Thanks in Advance..

Craig N6YUV




--
Untitled Document $('#quoted-196987018').on('show.bs.collapse', function () $('#qlabel-196987018').text("Hide quoted text"); ) $('#quoted-196987018').on('hide.bs.collapse', function () $('#qlabel-196987018').text("Show quoted text"); ) More

• All Messages By This Member

displayLikeStats("/g/repeater-builder", 2, 196987018, false) Joe Burkleo $('#timedispmsg196986309').replaceWith(DisplayShortTime(1638905263860198193, false)); #188742
Craig,
You should find the information here in this link that will get you pointed in the right direction.



Joe - WA7JAW More

• All Messages By This Member

displayLikeStats("/g/repeater-builder", 0, 196986309, false) Craig Ehlers N6YUV $('#timedispmsg196982108').replaceWith(DisplayShortTime(1638900589851458878, false)); #188729
We have 8 M1225 VHF radios that we would like to use for voting receivers. Is there a easy way to program them for them for the Amateur Bands.
FCC ID ABZ99FT3038. I do have a DOS computer I have been using for other Motorola radios and also CPS for the later stuff. Any help would really be appreciated.
Thanks in Advance..

Craig N6YUV More

• All Messages By This Member

displayLikeStats("/g/repeater-builder", 0, 196982108, false) Close Verify Delete Are you sure you wish to delete this message from the message archives of repeater...@groups.io? This cannot be undone. Cancel Yes Close Verify Repost Are you sure you wish to repost this message? Cancel Yes CloseReport MessageReasonReport to ModeratorsI think this message isn't appropriate for our group. The Group moderators are responsible for maintaining their community and can address these issues.Report to Groups.io SupportI think this violates the Terms of Service. This includes: harm to minors, violence or threats, harassment or privacy invasion, impersonation or misrepresentation, fraud or phishing.Note:Your email address is included with the abuse report.

eebf2c3492