Looking for Info on Clausing lathe
scotte...@yahoo.com
pretty cheap. It's my first and I need to learn how to use and
maintain the thing properly. It's a model 5320.
I haven't been able to locate any info on the 5300 series, so I'd also
appreciate it if anyone knows if the 5400 or any other model is
similar. I'd really love to locate a manual for the lathe, or if not,
then one as close as I can get. I did try calling Clausing a few
minutes ago but they were closed and their website says they don't have
the stuff so I'm not holding out hope.
I do already have the atlas book from the 30's and the south bend "how
to run a lathe" but I'm not sure if everything carries over. Right now
I'm trying to decide what kind of oil to put in the thing, then I need
to figure out how to cut 10 tpi threads.
Thanks for any help,
Scott
Rex B
for Atlas lathes from the 1930's still.
Have you tried the Yahoo group?
http://groups.yahoo.com/group/clausing_lathe_and_mill/
I have some Clausing files at home, I'll check tonight
--
- -
Rex Burkheimer
WM Automotive
Fort Worth TX
Mike Henry
or so) and even a few parts. Google should turn up a link in short order.
DoN. Nichols has a 5300, I think, and will probably weigh in a little later
this evening.
Mike
<scotte...@yahoo.com> wrote in message
news:1111703603.4...@f14g2000cwb.googlegroups.com...
Garrett Fulton
"Mike Henry" <Michae...@msn.com> wrote in message
news:d1vnb...@news2.newsguy.com...
I've got a 5310 and Clausing had the manual for it. Twenty something
dollars. Give them a try.
Garrett Fulton
DoN. Nichols
Mike Henry <michae...@msn.com> wrote:
>Contact Clausing - they still supply manuals at pretty nominal prices ($25
>or so) and even a few parts. Google should turn up a link in short order.
>
>DoN. Nichols has a 5300, I think, and will probably weigh in a little later
>this evening.
Nope! it is a 5418, not a 5300 series.
A few years ago, Clausing would happily sell a photocopied
manual tailored to your model number and serial number for a quite
reasonable amount. They can also tell you when yours was made.
That is the best bet, overall.
If that fails (e.g. they've stopped selling manual reprints),
drop me an e-mail and I'll see what I can do about a duplicate of mine
Good Luck,
DoN.
--
Email: <dnic...@d-and-d.com> | Voice (all times): (703) 938-4564
(too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html
--- Black Holes are where God is dividing by zero ---
Mike Henry
"DoN. Nichols" <dnic...@d-and-d.com> wrote in message
news:d20bpq$r1r$1...@fuego.d-and-d.com...
> In article <d1vnb...@news2.newsguy.com>,
> Mike Henry <michae...@msn.com> wrote:
>>Contact Clausing - they still supply manuals at pretty nominal prices ($25
>>or so) and even a few parts. Google should turn up a link in short order.
>>
>>DoN. Nichols has a 5300, I think, and will probably weigh in a little
>>later
>>this evening.
>
> Nope! it is a 5418, not a 5300 series.
Sorry - I always get the model number of yours confused, it seems.
> A few years ago, Clausing would happily sell a photocopied
> manual tailored to your model number and serial number for a quite
> reasonable amount. They can also tell you when yours was made.
Still do as of a few months ago.
Warren Oatley
If u look on ebay there are usually all the manuals for sale like 40 bucs
--
for full context, visit https://www.polytechforum.com/metalworking/looking-for-info-on-clausing-lathe-406434-.htm
Rick
Hello I was wondering if you know if the 5320 can be used for woodworking or
is it just a metal lathe
Rick
Jon Elson
> replying to Rex B, Rick wrote:
> Hello I was wondering if you know if the 5320 can be used for woodworking
> or is it just a metal lathe
>
enough spindle speed to do it properly, so you get some tearing of the
surface.
You do need to protect the ways from the wood dust, as some woods can be
corrosive.
Jon
Gerry
<0f8503901d844703ee...@example.com> wrote:
>replying to Mike Henry, Rick wrote:
>Hello I was wondering if you know if the 5320 can be used for woodworking or
>is it just a metal lathe
marshmallow
Jim Wilkins
news:jfoobd9u3qj32rvd3...@4ax.com...
in my 10" South Bend metal lathe, though a chuck holds as well or
better. The standard conical tailstock center is likely to split the
wood. HSS bits cut wood easily if not very smoothly. You may have to
make your own tool rest to support wood turning chisels. If the wood
isn't dry the chips can discolor the exposed bare steel in minutes.
https://www.ebay.com/itm/Heavy-Duty-Wood-Lathe-Turning-Spur-Live-Cup-Turning-Center-Set-MT2-Arbor-New-/291814642780
-jsw
Ed Huntress
Clausing was making the 5300-series, including the 5320, at least
until the mid-'50s.
It has a roller-rearing or ball-bearing spindle, which is better for
turning wood than our plain-bearing SBs, Jim. BTW, SB recommends
loosening the spindle-bearing caps if you're going to turn wood with
it. I never did so with mine, because I don't want to screw up its
near-perfect clearnaces for metalworking.
Rex, I turn wood and other materials in my SB, and it works fine. It
was once a popular machine for patternmakers, who make very accurate
pieces out of wood to use in casting patterns.
As others have said, it doesn't turn fast enough to get really clean
cuts in wood. I've ground some HSS tools to skew-cut wood (and cork;
I've used them for turning fishing-rod grips) and they cut pretty
clean, but they're limited in the geometry they'll cut.
Keep your cutting tools very sharp and just anticipate that you're
going to have to do some sanding to get a good finish.
--
Ed Huntress
Jim Wilkins
news:ud3qbdpi5a32mdtjl...@4ax.com...
ferrule, for example, but not to make furniture. For that I would
reassemble my Shopsmith.
-jsw