Extracting eMMC to image file on microSD card

[Kirk]

Regarding the instructions and the file "beagleboneblack-save-emmc.zip" file located here:

http://elinux.org/BeagleBone_Black_Extracting_eMMC_content

I've used it successfully in the past.

Now I tried it on an "Arrow BeagleBone Black Industrial" board and it doesn't work.

Should this work?  

Or do I need something new?

Thanks,

Kirk

[Kirk]

Maybe this will help:

Here's what the serial debug output looks like when it doesn't work.

I need some help interpreting it.

Thanks

U-Boot SPL 2013.04 (Sep 25 2013 - 00:49:30)

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)

musb-hdrc: MHDRC RTL version 2.0

musb-hdrc: setup fifo_mode 4

musb-hdrc: 28/31 max ep, 16384/16384 memory

USB Peripheral mode controller at 47401000 using PIO, IRQ 0

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)

musb-hdrc: MHDRC RTL version 2.0

musb-hdrc: setup fifo_mode 4

musb-hdrc: 28/31 max ep, 16384/16384 memory

USB Host mode controller at 47401800 using PIO, IRQ 0

OMAP SD/MMC: 0

reading u-boot.img

reading u-boot.img

U-Boot 2013.04 (Sep 25 2013 - 00:49:30)

I2C:   ready

DRAM:  512 MiB

WARNING: Caches not enabled

NAND:  No NAND device found!!!

0 MiB

MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1

*** Warning - readenv() failed, using default environment

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)

musb-hdrc: MHDRC RTL version 2.0

musb-hdrc: setup fifo_mode 4

musb-hdrc: 28/31 max ep, 16384/16384 memory

USB Peripheral mode controller at 47401000 using PIO, IRQ 0

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)

musb-hdrc: MHDRC RTL version 2.0

musb-hdrc: setup fifo_mode 4

musb-hdrc: 28/31 max ep, 16384/16384 memory

USB Host mode controller at 47401800 using PIO, IRQ 0

Net:   <ethaddr> not set. Validating first E-fuse MAC

cpsw, usb_ether

Hit any key to stop autoboot:  0

mmc0 is current device

SD/MMC found on device 0

reading uEnv.txt

236 bytes read in 7 ms (32.2 KiB/s)

Loaded environment from uEnv.txt

Importing environment from mmc ...

Running uenvcmd ...

reading uImage

11748096 bytes read in 1322 ms (8.5 MiB/s)

reading /am335x-boneblack.dtb

24884 bytes read in 12 ms (2 MiB/s)

## Booting kernel from Legacy Image at 80200000 ...

   Image Name:   Linux-3.8.13

   Image Type:   ARM Linux Kernel Image (uncompressed)

   Data Size:    11748032 Bytes = 11.2 MiB

   Load Address: 80008000

   Entry Point:  80008000

   Verifying Checksum ... OK

## Flattened Device Tree blob at 81ff0000

   Booting using the fdt blob at 0x81ff0000

   Loading Kernel Image ... OK

OK

   Using Device Tree in place at 81ff0000, end 81ff9133

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

[    1.368993] omap2_mbox_probe: platform not supported

[    1.380022] tps65217-bl tps65217-bl: no platform data provided

[    1.456012] bone-capemgr bone_capemgr.9: slot #0: No cape found

[    1.493120] bone-capemgr bone_capemgr.9: slot #1: No cape found

[    1.530230] bone-capemgr bone_capemgr.9: slot #2: No cape found

[    1.567340] bone-capemgr bone_capemgr.9: slot #3: No cape found

[    1.594051] omap_hsmmc mmc.5: of_parse_phandle_with_args of 'reset' failed

[    1.659528] pinctrl-single 44e10800.pinmux: pin 44e10854 already requested by 44e10800.pinmux; cannot claim for gpio-leds.8

[    1.671234] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.8) status -22

[    1.678546] pinctrl-single 44e10800.pinmux: could not request pin 21 on device pinctrl-single

Starting logging: OK

Initializing random number generator... done.

Starting network...

/etc/init.d/S93-am335x-pm-firmware-load: line 4: can't create /sys/devices/ocp.2/44d00000.wkup_m3/firmware/am335x-pm-firmware.bin/loading: nonexistent directory

/etc/init.d/S93-am335x-pm-firmware-load: line 5: can't create /sys/devices/ocp.2/44d00000.wkup_m3/firmware/am335x-pm-firmware.bin/data: nonexistent directory

/etc/init.d/S93-am335x-pm-firmware-load: line 6: can't create /sys/devices/ocp.2/44d00000.wkup_m3/firmware/am335x-pm-firmware.bin/loading: nonexistent directory

Running /dev/mmcblk0p1/autorun.sh...

dd: can't open '/dev/mmcblk1': No such file or directory

Welcome to Buildroot

beaglebone login:

Welcome to Buildroot

beaglebone login: