problem booting android 4.2.2 on baglebone

[mihir.n....@gmail.com]

I recently started working on baglebone. I followed the steps on 

http://processors.wiki.ti.com/index.php/TI-Android-JB-4.2.2-DevKit-4.1.1_UserGuide

&

http://processors.wiki.ti.com/index.php/BeagleBone-Android-DevKit_Guide#Hardware_setup

After establishing serial communication the window starts "cccc" as recommended. As instructed I insert the bootable sdmmc card into the beaglebone. Android starts booting and in the end the log stops... snippet of the log is as below. Now i dont know what i have to do. Please provide some support regarding it. I am using ubantu 11.10 using VMware on windows7 64bit

log..

root@android:/ # [    3.365753] android_work: sent uevent USB_STATE=CONNECTED                

[    3.371520] android_work: sent uevent USB_STATE=DISCONNECTED                              

[    3.379119] Disabling lock debugging due to kernel taint                                  

[    3.435455] android_work: sent uevent USB_STATE=CONNECTED                                 

[    3.784362] warning: `rild' uses 32-bit capabilities (legacy support in use)              

[    3.845520] android_work: sent uevent USB_STATE=DISCONNECTED                              

[    3.890869] android_work: did not send uevent (0 0   (null))                              

[    3.955291] android_work: sent uevent USB_STATE=CONNECTED                                 

[    4.109863] android_work: sent uevent USB_STATE=DISCONNECTED                              

[    4.141540] android_work: sent uevent USB_STATE=CONNECTED                                 

[    4.147369] android_work: sent uevent USB_STATE=DISCONNECTED                              

[    4.211578] android_work: sent uevent USB_STATE=CONNECTED                                 

[    4.377655]  gadget: high-speed config #1: android                                        

[    4.397521] android_work: sent uevent USB_STATE=CONFIGURED                                

[   20.203216] request_suspend_state: wakeup (3->0) at 20170814787 (2000-01-01 00:23:56.3389)

[   21.057922] net eth0: CPSW phy found : id is : 0x7c0f1                                    

[   21.064208] PHY 0:01 not found                                                            

[   21.076110] ADDRCONF(NETDEV_UP): eth0: link is not ready                                  

[   21.768341] acc_open                                                                      

[   21.773101] acc_release                                                                   

[   25.053070] PHY: 0:00 - Link is Up - 100/Full                                             

[   25.069183] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready                             

[   33.759277] init: sys_prop: permission denied uid:1003  name:service.bootanim.exit  

[Vishveshwar]

Congratulations! Android booted up. If you did not attach a LCD cape, that's all you get.. a working console with shell prompt.
The shell prompt got lost in the kernel boot messages, but it is there. Press Enter key again and you should see it.

-Vishveshwar

[kish...@gmail.com]

I am facing the same problem..but even after i press enter i get nothing...what might be wrong

[Nathan Proper]

Vishveshwar,

I saw your post.  I am using a BB VA6A With the LCD7 Cape Rev A3.  But The LCD7 cape displays nothing. I know the cape works I am able to load, display, and interact with Angstrom.

root@android:/ # [    6.571105] Disabling lock debugging due to kernel taint
[    6.645782] warning: `rild' uses 32-bit capabilities (legacy support in use)
[    6.680664] android_work: did not send uevent (0 0   (null))
[    6.766143] android_work: sent uevent USB_STATE=CONNECTED
[    6.772979]  gadget: high-speed config #1: android
[    6.778656] android_work: sent uevent USB_STATE=CONFIGURED
[   72.969177] request_suspend_state: wakeup (3->0) at 72936041438 (2000-01-01 00:01:11.328032443 UTC)
[   74.772583] net eth0: CPSW phy found : id is : 0x7c0f1
[   74.778808] PHY 0:01 not found
[   74.789642] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   75.644439] acc_open
[   75.647125] acc_release
[   77.763763] PHY: 0:00 - Link is Up - 100/Full
[   77.768554] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  184.802795] init: sys_prop: permission denied uid:1003  name:service.bootanim.exit

Cheers
Nathan