can't flash BBB

57 views

Skip to first unread message

blo...@nextlevelscada.com

unread,

Apr 27, 2015, 9:27:43 AM4/27/15

to beagl...@googlegroups.com

I have been trying to flash my BBB for days now. I have tried the latest 4gb and 2gb images from http://elinux.org/Beagleboard:BeagleBoneBlack_Debian

I format my 32gb card using the HP tool with FAT32 (only fat32 and NTFS are available for selection). I plug in power from 5v adapter while holding the user/boot button. initially everything looks fine. I get the wave pattern of user LEDs. about 10 minutes later all of the LEDs except user 1 LED are off and LED 1 is on solid. I'm not sure which BBB rev this is. Is there a way to find out? here's a dump from serial debug

U-Boot SPL 2015.01-00001-gb2412df (Jan 29 2015 - 15:01:06)

U-Boot 2015.01-00001-gb2412df (Jan 29 2015 - 15:01:06), Build: jenkins-github_Bootloader-Builder-105

Watchdog enabled

I2C: ready

DRAM: 512 MiB

MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1

Using default environment

Net: <ethaddr> not set. Validating first E-fuse MAC

cpsw

Hit any key to stop autoboot: 0

gpio: pin 53 (gpio 53) value is 1

switch to partitions #0, OK

mmc0 is current device

gpio: pin 54 (gpio 54) value is 1

Checking for: /uEnv.txt ...

933 bytes read in 9 ms (100.6 KiB/s)

gpio: pin 55 (gpio 55) value is 1

Loaded environment from uEnv.txt

Importing environment from mmc ...

Checking if uenvcmd is set ...

gpio: pin 56 (gpio 56) value is 1

Running uenvcmd ...

718 bytes read in 53 ms (12.7 KiB/s)

5617184 bytes read in 354 ms (15.1 MiB/s)

2287175 bytes read in 174 ms (12.5 MiB/s)

26098 bytes read in 81 ms (314.5 KiB/s)

Kernel image @ 0x82000000 [ 0x000000 - 0x55b620 ]

## Flattened Device Tree blob at 88000000

Booting using the fdt blob at 0x88000000

Using Device Tree in place at 88000000, end 880095f1

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

[ 0.000000] Booting Linux on physical CPU 0x0

[ 0.000000] Initializing cgroup subsys cpu

[ 0.000000] Linux version 3.8.13-bone70 (root@a5-imx6q-wandboard-2gb) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Fri Jan 23 02:15:42 UTC 2015

[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d

[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

[ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone

[ 0.000000] Memory policy: ECC disabled, Data cache writeback

[ 0.000000] AM335X ES2.1 (l2cache sgx neon )

[ 0.000000] PERCPU: Embedded 9 pages/cpu @c0d4e000 s14080 r8192 d14592 u36864

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129792

[ 0.000000] Kernel command line: console=tty0 console=ttyO0,115200n8 root=/dev/mmcblk0p1 rootfstype=ext4 rootwait fixrtc init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3.sh

[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)

[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)

[ 0.000000] __ex_table already sorted, skipping sort

[ 0.000000] allocated 1048576 bytes of page_cgroup

[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups

[ 0.000000] Memory: 511MB = 511MB total

[ 0.000000] Memory: 505912k/505912k available, 18376k reserved, 0K highmem

[ 0.000000] Virtual kernel memory layout:

[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)

[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)

[ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)

[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)

[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)

[ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB)

[ 0.000000] .text : 0xc0008000 - 0xc07fda30 (8151 kB)

[ 0.000000] .init : 0xc07fe000 - 0xc083b700 ( 246 kB)

[ 0.000000] .data : 0xc083c000 - 0xc08c3980 ( 543 kB)

[ 0.000000] .bss : 0xc08c3980 - 0xc093d140 ( 486 kB)

[ 0.000000] Hierarchical RCU implementation.

[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.

[ 0.000000] NR_IRQS:0 nr_irqs:0 0

[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts

[ 0.000000] Total of 128 interrupts on 1 active controller

[ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz

[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms

[ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz

[ 0.000000] Console: colour dummy device 80x30

[ 0.000000] console [tty0] enabled

[ 0.000639] Calibrating delay loop... 993.47 BogoMIPS (lpj=969728)

[ 0.029191] pid_max: default: 32768 minimum: 301

[ 0.029338] Security Framework initialized

[ 0.029403] Mount-cache hash table entries: 512

[ 0.035145] Initializing cgroup subsys cpuacct

[ 0.035191] Initializing cgroup subsys memory

[ 0.035238] Initializing cgroup subsys blkio

[ 0.035330] CPU: Testing write buffer coherency: ok

[ 0.035725] CPU0: thread -1, cpu 0, socket -1, mpidr 0

[ 0.035793] Setting up static identity map for 0x804d4d08 - 0x804d4d54

[ 0.036715] Brought up 1 CPUs

[ 0.036745] SMP: Total of 1 processors activated (993.47 BogoMIPS).

[ 0.037547] devtmpfs: initialized

[ 0.045872] omap_hwmod: wd_timer2: _wait_target_disable failed

[ 0.097997] pinctrl core: initialized pinctrl subsystem

[ 0.098151] rstctl core: initialized rstctl subsystem

[ 0.098434] regulator-dummy: no parameters

[ 0.098761] NET: Registered protocol family 16

[ 0.099292] DMA: preallocated 256 KiB pool for atomic coherent allocations

[ 0.104892] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568

[ 0.105527] platform 49000000.edma: alias fck already exists

[ 0.105557] platform 49000000.edma: alias fck already exists

[ 0.105578] platform 49000000.edma: alias fck already exists

[ 0.106298] OMAP GPIO hardware version 0.1

[ 0.108826] gpio-rctrl rstctl.4: loaded OK

[ 0.112207] No ATAGs?

[ 0.112233] hw-breakpoint: debug architecture 0x4 unsupported.

[ 0.113527] cpsw.0: No hwaddr in dt. Using 78:a5:04:bc:d6:16 from efuse

[ 0.113563] cpsw.1: No hwaddr in dt. Using 78:a5:04:bc:d6:18 from efuse

[ 0.121624] bio: create slab <bio-0> at 0

[ 0.127879] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver

[ 0.128185] vmmcsd_fixed: 3300 mV

[ 0.129790] SCSI subsystem initialized

[ 0.130044] usbcore: registered new interface driver usbfs

[ 0.130113] usbcore: registered new interface driver hub

[ 0.130325] usbcore: registered new device driver usb

[ 0.131595] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz

[ 0.132507] input: tps65217_pwr_but as /devices/ocp.3/44e0b000.i2c/i2c-0/0-0024/input/input0

[ 0.134123] DCDC1: at 1500 mV

[ 0.134987] vdd_mpu: 925 <--> 1325 mV at 1325 mV

[ 0.135807] vdd_core: 925 <--> 1150 mV at 1125 mV

[ 0.136663] LDO1: at 1800 mV

[ 0.137461] LDO2: at 3300 mV

[ 0.138952] LDO3: 1800 mV

[ 0.139764] LDO4: at 3300 mV

[ 0.140480] tps65217 0-0024: TPS65217 ID 0xe version 1.2

[ 0.140986] omap_i2c 44e0b000.i2c: unable to select pin group

[ 0.141466] omap_i2c 4819c000.i2c: bus 1 rev0.11 at 100 kHz

[ 0.142911] omap_i2c 4819c000.i2c: unable to select pin group

[ 0.143077] media: Linux media interface: v0.10

[ 0.143147] Linux video capture interface: v2.00

[ 0.143223] pps_core: LinuxPPS API ver. 1 registered

[ 0.143278] PTP clock support registered

[ 0.143671] Advanced Linux Sound Architecture Driver Initialized.

[ 0.144269] NetLabel: Initializing

[ 0.144290] NetLabel: domain hash size = 128

[ 0.144303] NetLabel: protocols = UNLABELED CIPSOv4

[ 0.144378] NetLabel: unlabeled traffic allowed by default

[ 0.144669] Switching to clocksource gp_timer

[ 0.175934] NET: Registered protocol family 2

[ 0.176653] TCP established hash table entries: 4096 (order: 3, 32768 bytes)

[ 0.176751] TCP bind hash table entries: 4096 (order: 4, 81920 bytes)

[ 0.176840] TCP: Hash tables configured (established 4096 bind 4096)

[ 0.176912] TCP: reno registered

[ 0.176933] UDP hash table entries: 256 (order: 1, 12288 bytes)

[ 0.176965] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)

[ 0.177210] NET: Registered protocol family 1

[ 0.177607] RPC: Registered named UNIX socket transport module.

[ 0.177637] RPC: Registered udp transport module.

[ 0.177651] RPC: Registered tcp transport module.

[ 0.177664] RPC: Registered tcp NFSv4.1 backchannel transport module.

[ 0.177892] Trying to unpack rootfs image as initramfs...

[ 0.339459] Freeing initrd memory: 2232K

[ 0.339804] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available

[ 0.340167] CPU PMU: attempt to register multiple PMU devices!

[ 0.340200] arm-pmu: probe of arm-pmu failed with error -28

[ 0.340516] omap2_mbox_probe: platform not supported

[ 0.490833] VFS: Disk quotas dquot_6.5.2

[ 0.491000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

[ 0.491721] NFS: Registering the id_resolver key type

[ 0.491804] Key type id_resolver registered

[ 0.491820] Key type id_legacy registered

[ 0.492105] fuse init (API version 7.20)

[ 0.492600] Btrfs loaded

[ 0.492733] msgmni has been set to 992

[ 0.494325] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)

[ 0.494443] io scheduler noop registered

[ 0.494462] io scheduler deadline registered

[ 0.494493] io scheduler cfq registered (default)

[ 0.495642] tps65217-bl tps65217-bl: no platform data provided

[ 0.495682] tps65217-bl: probe of tps65217-bl failed with error -22

[ 0.496215] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled

[ 0.497611] omap_uart 44e09000.serial: did not get pins for uart0 error: -19

[ 0.497909] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0

[ 1.259660] console [ttyO0] enabled

[ 1.264028] [drm] Initialized drm 1.1.0 20060810

[ 1.276144] brd: module loaded

[ 1.283081] loop: module loaded

[ 1.286483] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write

[ 1.293725] at24 1-0054: 32768 byte 24c256 EEPROM, writable, 1 bytes/write

[ 1.300960] at24 1-0055: 32768 byte 24c256 EEPROM, writable, 1 bytes/write

[ 1.308180] at24 1-0056: 32768 byte 24c256 EEPROM, writable, 1 bytes/write

[ 1.315408] at24 1-0057: 32768 byte 24c256 EEPROM, writable, 1 bytes/write

[ 1.329284] bone-capemgr bone_capemgr.9: Baseboard: 'A335BNLT,00C0,2414BBBK2043'

[ 1.337097] bone-capemgr bone_capemgr.9: compatible-baseboard=ti,beaglebone-black

[ 1.375216] bone-capemgr bone_capemgr.9: slot #0: No cape found

[ 1.412322] bone-capemgr bone_capemgr.9: slot #1: No cape found

[ 1.449432] bone-capemgr bone_capemgr.9: slot #2: No cape found

[ 1.486540] bone-capemgr bone_capemgr.9: slot #3: No cape found

[ 1.492765] bone-capemgr bone_capemgr.9: slot #4: specific override

[ 1.499331] bone-capemgr bone_capemgr.9: bone: Using override eeprom data at slot 4

[ 1.507340] bone-capemgr bone_capemgr.9: slot #4: 'Bone-LT-eMMC-2G,00A0,Texas Instrument,BB-BONE-EMMC-2G'

[ 1.517405] bone-capemgr bone_capemgr.9: slot #5: specific override

[ 1.523974] bone-capemgr bone_capemgr.9: bone: Using override eeprom data at slot 5

[ 1.531987] bone-capemgr bone_capemgr.9: slot #5: 'Bone-Black-HDMI,00A0,Texas Instrument,BB-BONELT-HDMI'

[ 1.541973] bone-capemgr bone_capemgr.9: slot #6: specific override

[ 1.548544] bone-capemgr bone_capemgr.9: bone: Using override eeprom data at slot 6

[ 1.556561] bone-capemgr bone_capemgr.9: slot #6: 'Bone-Black-HDMIN,00A0,Texas Instrument,BB-BONELT-HDMIN'

[ 1.566952] bone-capemgr bone_capemgr.9: loader: before slot-4 BB-BONE-EMMC-2G:00A0 (prio 1)

[ 1.575797] bone-capemgr bone_capemgr.9: loader: check slot-4 BB-BONE-EMMC-2G:00A0 (prio 1)

[ 1.584609] bone-capemgr bone_capemgr.9: loader: before slot-5 BB-BONELT-HDMI:00A0 (prio 1)

[ 1.593345] bone-capemgr bone_capemgr.9: loader: check slot-5 BB-BONELT-HDMI:00A0 (prio 1)

[ 1.602002] bone-capemgr bone_capemgr.9: initialized OK.

[ 1.607568] bone-capemgr bone_capemgr.9: loader: before slot-6 BB-BONELT-HDMIN:00A0 (prio 2)

[ 1.616399] bone-capemgr bone_capemgr.9: loader: check slot-6 BB-BONELT-HDMIN:00A0 (prio 2)

[ 1.626587] OneNAND driver initializing

[ 1.631555] usbcore: registered new interface driver cdc_ether

[ 1.637700] bone-capemgr bone_capemgr.9: loader: after slot-4 BB-BONE-EMMC-2G:00A0 (prio 1)

[ 1.646489] usbcore: registered new interface driver rndis_host

[ 1.652738] bone-capemgr bone_capemgr.9: loader: after slot-5 BB-BONELT-HDMI:00A0 (prio 1)

[ 1.661396] bone-capemgr bone_capemgr.9: loader: check slot-6 BB-BONELT-HDMIN:00A0 (prio 2)

[ 1.670206] usbcore: registered new interface driver cdc_ncm

[ 1.676153] bone-capemgr bone_capemgr.9: slot #4: Requesting firmware 'cape-bone-2g-emmc1.dtbo' for board-name 'Bone-LT-eMMC-2G', version '00A0'

[ 1.690155] usbcore: registered new interface driver cdc_acm

[ 1.696097] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters

[ 1.704460] Initializing USB Mass Storage driver...

[ 1.709582] bone-capemgr bone_capemgr.9: slot #4: dtbo 'cape-bone-2g-emmc1.dtbo' loaded; converting to live tree

[ 1.720264] bone-capemgr bone_capemgr.9: slot #5: Requesting firmware 'cape-boneblack-hdmi-00A0.dtbo' for board-name 'Bone-Black-HDMI', version '00A0'

[ 1.734426] usbcore: registered new interface driver usb-storage

[ 1.740710] USB Mass Storage support registered.

[ 1.745746] bone-capemgr bone_capemgr.9: slot #4: #2 overlays

[ 1.752372] bone-capemgr bone_capemgr.9: slot #4: Applied #2 overlays.

[ 1.759224] bone-capemgr bone_capemgr.9: loader: done slot-4 BB-BONE-EMMC-2G:00A0 (prio 1)

[ 1.767906] bone-capemgr bone_capemgr.9: loader: check slot-6 BB-BONELT-HDMIN:00A0 (prio 2)

[ 1.776671] bone-capemgr bone_capemgr.9: slot #5: dtbo 'cape-boneblack-hdmi-00A0.dtbo' loaded; converting to live tree

[ 1.788004] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)

[ 1.794578] musb-hdrc musb-hdrc.0.auto: pdev->id = 0

[ 1.799801] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:480 dsps_musb_init: OK

[ 1.809112] bone-capemgr bone_capemgr.9: slot #5: #4 overlays

[ 1.816502] platform 4830e000.fb: alias fck already exists

[ 1.822559] musb-hdrc musb-hdrc.0.auto: *** mode=3

[ 1.827615] musb-hdrc musb-hdrc.0.auto: *** power=250

[ 1.833861] bone-capemgr bone_capemgr.9: slot #5: Applied #4 overlays.

[ 1.840766] bone-capemgr bone_capemgr.9: loader: done slot-5 BB-BONELT-HDMI:00A0 (prio 1)

[ 1.849367] bone-capemgr bone_capemgr.9: loader: check slot-6 BB-BONELT-HDMIN:00A0 (prio 2)

[ 1.858558] musb-hdrc musb-hdrc.1.auto: pdev->id = 1

[ 1.863793] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:480 dsps_musb_init: OK

[ 1.872621] bone-capemgr bone_capemgr.9: loader: after slot-6 BB-BONELT-HDMIN:00A0 (prio 2)

[ 1.881519] musb-hdrc musb-hdrc.1.auto: *** mode=1

[ 1.886551] musb-hdrc musb-hdrc.1.auto: *** power=250

[ 1.891850] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver

[ 1.897893] bone-capemgr bone_capemgr.9: slot #6: Requesting firmware 'cape-boneblack-hdmin-00A0.dtbo' for board-name 'Bone-Black-HDMIN', version '00A0'

[ 1.912439] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1

[ 1.920793] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

[ 1.927916] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[ 1.935474] usb usb1: Product: MUSB HDRC host driver

[ 1.940670] usb usb1: Manufacturer: Linux 3.8.13-bone70 musb-hcd

[ 1.946958] usb usb1: SerialNumber: musb-hdrc.1.auto

[ 1.952204] bone-capemgr bone_capemgr.9: slot #6: dtbo 'cape-boneblack-hdmin-00A0.dtbo' loaded; converting to live tree

[ 1.964083] hub 1-0:1.0: USB hub found

[ 1.968065] hub 1-0:1.0: 1 port detected

[ 1.972383] bone-capemgr bone_capemgr.9: slot #6: BB-BONELT-HDMIN conflict P8.45 (#5:BB-BONELT-HDMI)

[ 1.981952] bone-capemgr bone_capemgr.9: slot #6: Failed verification

[ 1.988701] bone-capemgr bone_capemgr.9: loader: failed to load slot-6 BB-BONELT-HDMIN:00A0 (prio 2)

[ 1.999042] mousedev: PS/2 mouse device common for all mice

[ 2.006741] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0

[ 2.014398] i2c /dev entries driver

[ 2.019044] pps_ldisc: PPS line discipline registered

[ 2.024615] Driver for 1-wire Dallas network protocol.

[ 2.031219] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec

[ 2.038907] device-mapper: ioctl: 4.23.1-ioctl (2012-12-18) initialised: dm-d...@redhat.com

[ 2.047814] cpuidle: using governor ladder

[ 2.052146] cpuidle: using governor menu

[ 2.056576] omap_hsmmc mmc.5: of_parse_phandle_with_args of 'reset' failed

[ 2.063792] omap_hsmmc mmc.5: Failed to get rstctl; not using any

[ 2.070473] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25

[ 2.077645] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24

[ 2.084912] mmc.5 supply vmmc_aux not found, using dummy regulator

[ 2.091704] omap_hsmmc mmc.5: pins are not configured from the driver

[ 2.125459] gpio-rctrl rstctl.4: gpio_rctrl_request eMMC_RSTn

[ 2.131617] omap_hsmmc mmc.11: Got rstctl (gpio:#0 name eMMC_RSTn) label:eMMC_RSTn

[ 2.139579] gpio-rctrl rstctl.4: gpio_rctrl_deassert eMMC_RSTn

[ 2.145905] edma-dma-engine edma-dma-engine.0: allocated channel for 0:3

[ 2.153002] edma-dma-engine edma-dma-engine.0: allocated channel for 0:2

[ 2.160398] mmc.11 supply vmmc_aux not found, using dummy regulator

[ 2.167056] omap_hsmmc mmc.11: pins are not configured from the driver

[ 2.201731] pinctrl-single 44e10800.pinmux: pin 44e10854 already requested by 44e10800.pinmux; cannot claim for gpio-leds.8

[ 2.213407] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.8) status -22

[ 2.220690] pinctrl-single 44e10800.pinmux: could not request pin 21 on device pinctrl-single

[ 2.229627] leds-gpio gpio-leds.8: pins are not configured from the driver

[ 2.237559] ledtrig-cpu: registered to indicate activity on CPUs

[ 2.244144] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36

[ 2.251340] omap-sham 53100000.sham: hw accel on OMAP rev 4.3

[ 2.258807] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2

[ 2.265031] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5

[ 2.272170] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6

[ 2.282173] usbcore: registered new interface driver usbhid

[ 2.288090] usbhid: USB HID core driver

[ 2.292991] ashmem: initialized

[ 2.296397] mmc0: host does not support reading read-only switch. assuming write-enable.

[ 2.305110] logger: created 256K log 'log_main'

[ 2.310108] logger: created 256K log 'log_events'

[ 2.315166] mmc0: new high speed SDHC card at address aaaa

[ 2.321124] logger: created 256K log 'log_radio'

[ 2.326444] mmcblk0: mmc0:aaaa SU32G 29.7 GiB

[ 2.331322] logger: created 256K log 'log_system'

[ 2.337641] mmcblk0: p1

[ 2.343098] davinci_evm sound.14: nxp-hdmi-hifi <-> 48038000.mcasp mapping ok

[ 2.352804] TCP: cubic registered

[ 2.356421] NET: Registered protocol family 10

[ 2.361901] NET: Registered protocol family 17

[ 2.366870] Key type dns_resolver registered

[ 2.371533] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3

[ 2.379659] ThumbEE CPU extension supported.

[ 2.384175] Registering SWP/SWPB emulation handler

[ 2.389885] registered taskstats version 1

[ 2.395980] tilcdc 4830e000.fb: No power control GPIO

[ 2.466945] mmc1: BKOPS_EN bit is not set

[ 2.475032] mmc1: new high speed MMC card at address 0001

[ 2.481225] mmcblk1: mmc1:0001 MMC04G 3.60 GiB

[ 2.486204] mmcblk1boot0: mmc1:0001 MMC04G partition 1 2.00 MiB

[ 2.492619] mmcblk1boot1: mmc1:0001 MMC04G partition 2 2.00 MiB

[ 2.499885] mmcblk1: p1

[ 2.504011] mmcblk1boot1: unknown partition table

[ 2.510337] mmcblk1boot0: unknown partition table

[ 2.517824] tilcdc 4830e000.fb: found TDA19988

[ 2.523089] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).

[ 2.530051] [drm] No driver support for vblank timestamp query.

[ 2.536529] tilcdc 4830e000.fb: No connectors reported connected with modes

[ 2.543865] [drm] Cannot find any crtc or sizes - going 1024x768

[ 2.559426] Console: switching to colour frame buffer device 128x48

[ 2.572107] tilcdc 4830e000.fb: fb0: frame buffer device

[ 2.577827] tilcdc 4830e000.fb: registered panic notifier

[ 2.583553] [drm] Initialized tilcdc 1.0.0 20121205 on minor 0

[ 2.638896] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6

[ 2.645387] davinci_mdio 4a101000.mdio: detected phy mask fffffffe

[ 2.658305] libphy: 4a101000.mdio: probed

[ 2.662695] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720

[ 2.672604] Detected MACID = 78:a5:04:bc:d6:16

[ 2.677294] cpsw 4a100000.ethernet: NAPI disabled

[ 2.684090] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801)

[ 2.697948] ALSA device list:

[ 2.701175] #0: TI BeagleBone Black

[ 2.705700] Freeing init memory: 244K

Loading, please wait...

[ 2.761041] udevd[99]: starting version 175

Begin: Loading essential drivers ... done.

Begin: Running /scripts/init-premount ... done.

Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.

Begin: Running /scripts/local-premount ... done.

[ 4.027961] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)

Begin: Running /scripts/local-bottom ... done.

done.

Begin: Running /scripts/init-bottom ... done.

Starting eMMC Flasher

-----------------------------

Checking for Valid BBB EEPROM header

Valid BBB EEPROM header found

-----------------------------

copying: [/dev/mmcblk0] -> [/dev/mmcblk1]

lsblk:

NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT

mmcblk1boot0 179:16 0 2M 1 disk

mmcblk1boot1 179:24 0 2M 1 disk

mmcblk0 179:0 0 29.7G 0 disk

`-mmcblk0p1 179:1 0 1.7G 0 part /

mmcblk1 179:8 0 3.6G 0 disk

`-mmcblk1p1 179:9 0 3.6G 0 part

-----------------------------

df -h | grep rootfs:

df: cannot read table of mounted file systems: No such file or directory

-----------------------------

Erasing: /dev/mmcblk1

108+0 records in

108+0 records out

113246208 bytes (113 MB) copied, 12.1734 s, 9.3 MB/s

108+0 records in

108+0 records out

113246208 bytes (113 MB) copied, 3.59623 s, 31.5 MB/s

Erasing: /dev/mmcblk1 complete

-----------------------------

Writing bootloader to [/dev/mmcblk1]

dd if=/opt/backup/uboot/MLO of=/dev/mmcblk1 count=1 seek=1 conv=notrunc bs=128k

-----------------------------

0+1 records in

0+1 records out

73516 bytes (74 kB) copied, 0.0325348 s, 2.3 MB/s

-----------------------------

dd if=/opt/backup/uboot/u-boot.img of=/dev/mmcblk1 count=2 seek=1 conv=notrunc bs=384k

-----------------------------

1+1 records in

1+1 records out

393496 bytes (393 kB) copied, 0.0642242 s, 6.1 MB/s

-----------------------------

Formatting: /dev/mmcblk1

Checking that no[ 20.820281] mmcblk1: unknown partition table

-one is using this disk right now ...

Disk /dev/mmcblk1: [ 20.832956] mmcblk1: p1

118016 cylinders, 4 heads, 16 sectors/track

sfdisk: ERROR: sector 3069678589 does not have an msdos signature

/dev/mmcblk1: unrecognized partition table type

Old situation:

No partitions found

New situation:

Units = mebibytes of 1048576 bytes, blocks of 1024 bytes, counting from 0

Device Boot Start End MiB #blocks Id System

/dev/mmcblk1p1 * 1 3687 3687 3775488 83 Linux

/dev/mmcblk1p2 0 - 0 0 0 Empty

/dev/mmcblk1p3 0 - 0 0 0 Empty

/dev/mmcblk1p4 0 - 0 0 0 Empty

Successfully wrote the new partition table

Re-reading the partition table ...

If you created or changed a DOS partition, /dev/foo7, say, then use dd(1)

to zero the first 512 bytes: dd if=/dev/zero of=/dev/foo7 bs=512 count=1

(See fdisk(8).)

mkfs.ext4 /dev/mmcblk1p1 -L BEAGLEBONE

-----------------------------

mke2fs 1.42.5 (29-Jul-2012)

ext2fs_check_if_mount: Can't check if filesystem is mounted due to missing mtab file while determining whether /dev/mmcblk1p1 is mounted.

Discarding device blocks: done

Filesystem label=BEAGLEBONE

OS type: Linux

Block size=4096 (log=2)

Fragment size=4096 (log=2)

Stride=0 blocks, Stripe width=0 blocks

236176 inodes, 943872 blocks

47193 blocks (5.00%) reserved for the super user

First data block=0

Maximum filesystem blocks=968884224

29 block groups

32768 blocks per group, 32768 fragments per group

8144 inodes per group

Superblock backups stored on blocks:

32768, 98304, 163840, 229376, 294912, 819200, 884736

Allocating group tables: done

Writing inode tables: done

Creating journal (16384 blocks): done

Writing superblocks and filesystem accounting information: done

-----------------------------

Formatting: /dev/mmcblk1 complete

-----------------------------

Copying: /dev/mmcblk0p1 -> /dev/mmcblk1p1

[ 28.618582] EXT4-fs (mmcblk1p1): mounted filesystem with ordered data mode. Opts: (null)

rsync: / -> /tmp/rootfs/

rsync: ignore the % values when shown as they are not accurate...

[ 120.488545] INFO: task mmcqd/0:71 blocked for more than 60 seconds.

[ 120.497457] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.

[ 120.507849] mmcqd/0 D c04d04a5 0 71 2 0x00000000

[ 120.516796] Kernel panic - not syncing: hung_task: blocked tasks

[ 120.525299] [<c00114f1>] (unwind_backtrace+0x1/0x9c) from [<c04cb2fd>] (panic+0x59/0x15c)

[ 120.536066] [<c04cb2fd>] (panic+0x59/0x15c) from [<c0073955>] (watchdog+0x19d/0x1c0)

[ 120.546417] [<c0073955>] (watchdog+0x19d/0x1c0) from [<c00454eb>] (kthread+0x6b/0x78)

[ 120.556893] [<c00454eb>] (kthread+0x6b/0x78) from [<c000c8fd>] (ret_from_fork+0x11/0x34)

[ 120.567664] drm_kms_helper: panic occurred, switching back to text console

this was using the 2gb flasher image. I used this one last in case I only have 2gb on my BBB emmc.

Thanks for you help.

Robert Nelson

unread,

Apr 27, 2015, 10:10:55 AM4/27/15

to Beagle Board

On Fri, Apr 24, 2015 at 8:14 PM, <blo...@nextlevelscada.com> wrote:
> I have been trying to flash my BBB for days now. I have tried the latest
> 4gb and 2gb images from http://elinux.org/Beagleboard:BeagleBoneBlack_Debian
>
> I format my 32gb card using the HP tool with FAT32 (only fat32 and NTFS are
> available for selection). I plug in power from 5v adapter while holding the
> user/boot button. initially everything looks fine. I get the wave pattern
> of user LEDs. about 10 minutes later all of the LEDs except user 1 LED are
> off and LED 1 is on solid. I'm not sure which BBB rev this is. Is there a
> way to find out? here's a dump from serial debug

No reason to do the extra HP tool step..

> [ 120.488545] INFO: task mmcqd/0:71 blocked for more than 60 seconds.
> [ 120.497457] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables
> this message.
> [ 120.507849] mmcqd/0 D c04d04a5 0 71 2 0x00000000
> [ 120.516796] Kernel panic - not syncing: hung_task: blocked tasks
> [ 120.525299] [<c00114f1>] (unwind_backtrace+0x1/0x9c) from [<c04cb2fd>]
> (panic+0x59/0x15c)
> [ 120.536066] [<c04cb2fd>] (panic+0x59/0x15c) from [<c0073955>]
> (watchdog+0x19d/0x1c0)
> [ 120.546417] [<c0073955>] (watchdog+0x19d/0x1c0) from [<c00454eb>]
> (kthread+0x6b/0x78)
> [ 120.556893] [<c00454eb>] (kthread+0x6b/0x78) from [<c000c8fd>]
> (ret_from_fork+0x11/0x34)

We see this from time to time with the old v3.8.x kernel. Usually it's
an indication of not enough power as rsync hit's both media devices
hard. But sometimes it's the media too.

So, make sure you using a 5v 2A dc power supply, but also try a
different microSD card.

Regards,

--
Robert Nelson
https://rcn-ee.com/

Message has been deleted

evilwulfie

unread,

Apr 28, 2015, 1:55:13 PM4/28/15

to beagl...@googlegroups.com

images here always worked for me

http://beagleboard.org/latest-images

On 4/28/2015 10:35 AM, rh_ wrote:

> On Fri, 24 Apr 2015 18:14:52 -0700 (PDT)
> blo...@nextlevelscada.com wrote:
>
>> I have been trying to flash my BBB for days now. I have tried the
>> latest 4gb and 2gb images
>> from http://elinux.org/Beagleboard:BeagleBoneBlack_Debian