Dado blades for table saw

[Andrew Ricke]

Do we have dado blades for the table saw?  I'm guessing not and that we don't have a sled setup for dado cuts either, but figured I'd check first. 

I guess I should even ask if it was operational for use. 

[Hroller McKnutt]

There is a Dado set at the space, I think it's on the bottom shelf of one of the tables. You'd have to make a zero clearance insert (or purpose built sled) I suppose... but there is a dado set somewhere in that shop..

Mike

On Mon, Jul 13, 2015 at 2:08 PM, Andrew Ricke <andrew...@gmail.com> wrote:

Do we have dado blades for the table saw?  I'm guessing not and that we don't have a sled setup for dado cuts either, but figured I'd check first. 

I guess I should even ask if it was operational for use. 

--
You received this message because you are subscribed to the Google Groups "Arch Reactor" group.
To unsubscribe from this group and stop receiving emails from it, send an email to arch-reactor...@googlegroups.com.
To post to this group, send email to arch-r...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/arch-reactor/CABOBYTx6N6piNAPJ0DiC03T9whV6eAyxvx1G%3D%3DtqArHjEhQ0YQ%40mail.gmail.com.
For more options, visit https://groups.google.com/d/optout.

--

Nullo edactore ligni, consilium cedet. - Countess Magda

[Andrew Ricke]

Thanks!  I'll look for it. I may just go the straight bit on the router route but I got a lot of 4x4s I want to lap joint. 

To view this discussion on the web visit https://groups.google.com/d/msgid/arch-reactor/CAAMjFk5NVeVMYu3GB4ueTU_F7KNz49Mt1Q0bb4_%2BhX1M2aWvcg%40mail.gmail.com.

[Chris Weiss]

the Dado set is in a wooden case on the shelf under the router table.  there is an insert for it, but it's not zero clearance, and no specific sled, which is probably fine for lap joins for 2x4's.

[Hroller McKnutt]

If you find it, make sure you respect it... that dado blade was how I lost part of my left middle finger. ;)

Mike

To view this discussion on the web visit https://groups.google.com/d/msgid/arch-reactor/CABOBYTzE9zT50NFazCVV6qtmMg8nw1YsOm0JxnrdwHiJC3sdxA%40mail.gmail.com.

For more options, visit https://groups.google.com/d/optout.

[Myles Farrell]

They are exactly where chris said, however i did make a zero clearance insert out of mdf for them. It should be in the rack to the right with the rest

To view this discussion on the web visit https://groups.google.com/d/msgid/arch-reactor/CAAMjFk7PXFRGOPg1gPscd3DoqLwXmLt49eCDj35P3S7P2h9hWg%40mail.gmail.com.

[Chris Weiss]

that would only apply to the right-side though right?  unless you put all the blades in?

[Andrew Ricke]

Ah cool. I should be good to go then.  Maybe I'll make a quick sled so I can keep my fingers and the 90. 

On Monday, July 13, 2015, Chris Weiss <cwe...@gmail.com> wrote:

that would only apply to the right-side though right?  unless you put all the blades in?

--

You received this message because you are subscribed to the Google Groups "Arch Reactor" group.
To unsubscribe from this group and stop receiving emails from it, send an email to arch-reactor...@googlegroups.com.
To post to this group, send email to arch-r...@googlegroups.com.

To view this discussion on the web visit https://groups.google.com/d/msgid/arch-reactor/CAEhO07MBjwYr29TWq6bTSxqAXZMdycovGGE6O0NZQPau%2BF_yfw%40mail.gmail.com.