unexpected keyword argument 'log_level'
257 views
Skip to first unread message
craig....@gmail.com
Mar 22, 2021, 4:18:00 PM3/22/21
to weewx-user
I have two problems that I may have caused myself (noob). I have had weewx running fine on my raspberry pi for several years. After updating weewx to V 4.4 and changing the forecast extension from NWS to Aeris for forecast both problems showed up. My station type is SDR.
First problem:
Years ago when I first set up the SDR driver I was able to suppress all the SDR data in the log so they didn't clutter the log.....I can't remember what i did.
The second problem:
More serious than the first is an error in the Forecast extension that stops the thread.
unexpected keyword argument 'log_level'
Because I have a hard time understanding python I dont understand how to fix things and need some help.
As far as I can tell weewx is working fine and the error is confined to the forecast extension. Thank you in advance for any insight you can give.
my log:
Mar 22 13:05:11 raspberrypi weewxd: sdr: MainThread: packet={u'extraHumid2': 33.0, u'extraTemp2': 21.5, u'txTempBatteryStatus': 0, 'usUnits': 16, 'dateTime': 1616439908}
Mar 22 13:05:11 raspberrypi weewxd: sdr: MainThread: ignoring duplicate packet {u'extraHumid2': 33.0, u'extraTemp2': 21.5, u'txTempBatteryStatus': 0, 'usUnits': 16, 'dateTime': 1616439908}
Mar 22 13:05:11 raspberrypi weewxd: sdr: MainThread: ignoring duplicate packet {u'extraHumid2': 33.0, u'extraTemp2': 21.5, u'txTempBatteryStatus': 0, 'usUnits': 16, 'dateTime': 1616439908}
Mar 22 13:05:15 raspberrypi weewxd: sdr: MainThread: lines=['{"time" : "2021-03-22 19:05:12", "model" : "Acurite 5n1 sensor", "sensor_id" : 1323, "channel" : "A", "sequence_num" : 0, "battery" : "OK", "message_type" : 56, "wind_speed" : 1.650, "temperature_F" : 45.300, "humidity" : 63}\n', '{"time" : "2021-03-22 19:05:12", "model" : "Acurite 5n1 sensor", "sensor_id" : 1323, "channel" : "A", "sequence_num" : 1, "battery" : "OK", "message_type" : 56, "wind_speed" : 1.650, "temperature_F" : 45.300, "humidity" : 63}\n', '{"time" : "2021-03-22 19:05:12", "model" : "Acurite 5n1 sensor", "sensor_id" : 1323, "channel" : "A", "sequence_num" : 2, "battery" : "OK", "message_type" : 56, "wind_speed" : 1.650, "temperature_F" : 45.300, "humidity" : 63}\n']
Mar 22 13:05:15 raspberrypi weewxd: sdr: MainThread: packet={u'outHumidity': 63.0, u'outTempBatteryStatus': 0, 'dateTime': 1616439912, u'outTemp': 45.3, u'windSpeed': 1.65, 'usUnits': 1}
Mar 22 13:05:15 raspberrypi weewxd: sdr: MainThread: packet={u'outHumidity': 63.0, u'outTempBatteryStatus': 0, 'dateTime': 1616439912, u'outTemp': 45.3, u'windSpeed': 1.65, 'usUnits': 1}
Mar 22 13:05:15 raspberrypi weewxd: sdr: MainThread: packet={u'outHumidity': 63.0, u'outTempBatteryStatus': 0, 'dateTime': 1616439912, u'outTemp': 45.3, u'windSpeed': 1.65, 'usUnits': 1}
Mar 22 13:05:18 raspberrypi weewxd: sdr: MainThread: lines=[]
Mar 22 13:05:22 raspberrypi weewxd: sdr: MainThread: lines=['{"time" : "2021-03-22 19:05:19", "model" : "Acurite tower sensor", "id" : 11823, "channel" : "C", "temperature_C" : 20.500, "humidity" : 25, "battery" : 0, "status" : 68}\n', '{"time" : "2021-03-22 19:05:19", "model" : "Acurite tower sensor", "id" : 11823, "channel" : "C", "temperature_C" : 20.500, "humidity" : 25, "battery" : 0, "status" : 68}\n', '{"time" : "2021-03-22 19:05:19", "model" : "Acurite tower sensor", "id" : 11823, "channel" : "C", "temperature_C" : 20.500, "humidity" : 25, "battery" : 0, "status" : 68}\n']
Mar 22 13:05:22 raspberrypi weewxd: sdr: MainThread: packet={'dateTime': 1616439919, u'inHumidity': 25.0, u'inTemp': 20.5, 'usUnits': 16, u'inTempBatteryStatus': 0}
Mar 22 13:05:22 raspberrypi weewx[1769] INFO weewx.manager: Added record 2021-03-22 13:05:00 MDT (1616439900) to database 'weewx.sdb'
Mar 22 13:05:22 raspberrypi weewx[1769] INFO weewx.manager: Added record 2021-03-22 13:05:00 MDT (1616439900) to daily summary in 'weewx.sdb'
Mar 22 13:05:22 raspberrypi weewxd: forecast: MainThread: Zambretti: starting thread
Mar 22 13:05:22 raspberrypi weewxd: forecast: ZambrettiThread: Zambretti: forecast was already calculated for 2021-03-22 09:00:00 MDT (1616425200)
Mar 22 13:05:22 raspberrypi weewxd: forecast: ZambrettiThread: Zambretti: terminating thread
Mar 22 13:05:22 raspberrypi weewxd: forecast: MainThread: Aeris: starting thread
Mar 22 13:05:22 raspberrypi weewxd: forecast: AerisThread: Aeris: download forecast from 'http://api.aerisapi.com/forecasts/closest?client_id=XXXXXXXXXXXXXXXXX3Da0&client_secret=XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXQ5nw&p=39.5468333,-104.978&filter=1hr'
Mar 22 13:05:22 raspberrypi weewx[1769] INFO weewx.restx: PWSWeather: Published record 2021-03-22 13:05:00 MDT (1616439900)
Mar 22 13:05:22 raspberrypi weewxd: forecast: AerisThread: Aeris: got 24 forecast records
Mar 22 13:05:22 raspberrypi weewxd: forecast: AerisThread: Aeris: saving 24 forecast records
Mar 22 13:05:22 raspberrypi weewxd: forecast: AerisThread: Aeris: forecast failure: addRecord() got an unexpected keyword argument 'log_level'
Mar 22 13:05:22 raspberrypi weewxd: forecast: AerisThread: Aeris: terminating thread
Mar 22 13:05:22 raspberrypi weewx[1769] INFO weewx.restx: Wunderground-PWS: Published record 2021-03-22 13:05:00 MDT (1616439900)
Mar 22 13:05:24 raspberrypi weewx[1769] INFO weewx.cheetahgenerator: Generated 20 files for report StandardReport in 2.26 seconds
Mar 22 13:05:25 raspberrypi weewx[1769] INFO weewx.imagegenerator: Generated 12 images for report StandardReport in 1.04 seconds
Mar 22 13:05:25 raspberrypi weewx[1769] INFO weewx.reportengine: Copied 0 files to /var/www/html/weewx
Mar 22 13:05:27 raspberrypi weewxd: sdr: MainThread: lines=['{"time" : "2021-03-22 19:05:24", "model" : "Acurite tower sensor", "id" : 6771, "channel" : "B", "temperature_C" : 21.500, "humidity" : 33, "battery" : 0, "status" : 68}\n', '{"time" : "2021-03-22 19:05:24", "model" : "Acurite tower sensor", "id" : 6771, "channel" : "B", "temperature_C" : 21.500, "humidity" : 33, "battery" : 0, "status" : 68}\n', '{"time" : "2021-03-22 19:05:24", "model" : "Acurite tower sensor", "id" : 6771, "channel" : "B", "temperature_C" : 21.500, "humidity" : 33, "battery" : 0, "status" : 68}\n']
Mar 22 13:05:27 raspberrypi weewxd: sdr: MainThread: packet={u'extraHumid2': 33.0, u'extraTemp2': 21.5, u'txTempBatteryStatus': 0, 'usUnits': 16, 'dateTime': 1616439924}
Mar 22 13:05:27 raspberrypi weewxd: sdr: MainThread: ignoring duplicate packet {u'extraHumid2': 33.0, u'extraTemp2': 21.5, u'txTempBatteryStatus': 0, 'usUnits': 16, 'dateTime': 1616439924}
Mar 22 13:05:27 raspberrypi weewxd: sdr: MainThread: ignoring duplicate packet {u'extraHumid2': 33.0, u'extraTemp2': 21.5, u'txTempBatteryStatus': 0, 'usUnits': 16, 'dateTime': 1616439924}
Mar 22 13:05:11 raspberrypi weewxd: sdr: MainThread: ignoring duplicate packet {u'extraHumid2': 33.0, u'extraTemp2': 21.5, u'txTempBatteryStatus': 0, 'usUnits': 16, 'dateTime': 1616439908}
Mar 22 13:05:11 raspberrypi weewxd: sdr: MainThread: ignoring duplicate packet {u'extraHumid2': 33.0, u'extraTemp2': 21.5, u'txTempBatteryStatus': 0, 'usUnits': 16, 'dateTime': 1616439908}
Mar 22 13:05:15 raspberrypi weewxd: sdr: MainThread: lines=['{"time" : "2021-03-22 19:05:12", "model" : "Acurite 5n1 sensor", "sensor_id" : 1323, "channel" : "A", "sequence_num" : 0, "battery" : "OK", "message_type" : 56, "wind_speed" : 1.650, "temperature_F" : 45.300, "humidity" : 63}\n', '{"time" : "2021-03-22 19:05:12", "model" : "Acurite 5n1 sensor", "sensor_id" : 1323, "channel" : "A", "sequence_num" : 1, "battery" : "OK", "message_type" : 56, "wind_speed" : 1.650, "temperature_F" : 45.300, "humidity" : 63}\n', '{"time" : "2021-03-22 19:05:12", "model" : "Acurite 5n1 sensor", "sensor_id" : 1323, "channel" : "A", "sequence_num" : 2, "battery" : "OK", "message_type" : 56, "wind_speed" : 1.650, "temperature_F" : 45.300, "humidity" : 63}\n']
Mar 22 13:05:15 raspberrypi weewxd: sdr: MainThread: packet={u'outHumidity': 63.0, u'outTempBatteryStatus': 0, 'dateTime': 1616439912, u'outTemp': 45.3, u'windSpeed': 1.65, 'usUnits': 1}
Mar 22 13:05:15 raspberrypi weewxd: sdr: MainThread: packet={u'outHumidity': 63.0, u'outTempBatteryStatus': 0, 'dateTime': 1616439912, u'outTemp': 45.3, u'windSpeed': 1.65, 'usUnits': 1}
Mar 22 13:05:15 raspberrypi weewxd: sdr: MainThread: packet={u'outHumidity': 63.0, u'outTempBatteryStatus': 0, 'dateTime': 1616439912, u'outTemp': 45.3, u'windSpeed': 1.65, 'usUnits': 1}
Mar 22 13:05:18 raspberrypi weewxd: sdr: MainThread: lines=[]
Mar 22 13:05:22 raspberrypi weewxd: sdr: MainThread: lines=['{"time" : "2021-03-22 19:05:19", "model" : "Acurite tower sensor", "id" : 11823, "channel" : "C", "temperature_C" : 20.500, "humidity" : 25, "battery" : 0, "status" : 68}\n', '{"time" : "2021-03-22 19:05:19", "model" : "Acurite tower sensor", "id" : 11823, "channel" : "C", "temperature_C" : 20.500, "humidity" : 25, "battery" : 0, "status" : 68}\n', '{"time" : "2021-03-22 19:05:19", "model" : "Acurite tower sensor", "id" : 11823, "channel" : "C", "temperature_C" : 20.500, "humidity" : 25, "battery" : 0, "status" : 68}\n']
Mar 22 13:05:22 raspberrypi weewxd: sdr: MainThread: packet={'dateTime': 1616439919, u'inHumidity': 25.0, u'inTemp': 20.5, 'usUnits': 16, u'inTempBatteryStatus': 0}
Mar 22 13:05:22 raspberrypi weewx[1769] INFO weewx.manager: Added record 2021-03-22 13:05:00 MDT (1616439900) to database 'weewx.sdb'
Mar 22 13:05:22 raspberrypi weewx[1769] INFO weewx.manager: Added record 2021-03-22 13:05:00 MDT (1616439900) to daily summary in 'weewx.sdb'
Mar 22 13:05:22 raspberrypi weewxd: forecast: MainThread: Zambretti: starting thread
Mar 22 13:05:22 raspberrypi weewxd: forecast: ZambrettiThread: Zambretti: forecast was already calculated for 2021-03-22 09:00:00 MDT (1616425200)
Mar 22 13:05:22 raspberrypi weewxd: forecast: ZambrettiThread: Zambretti: terminating thread
Mar 22 13:05:22 raspberrypi weewxd: forecast: MainThread: Aeris: starting thread
Mar 22 13:05:22 raspberrypi weewxd: forecast: AerisThread: Aeris: download forecast from 'http://api.aerisapi.com/forecasts/closest?client_id=XXXXXXXXXXXXXXXXX3Da0&client_secret=XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXQ5nw&p=39.5468333,-104.978&filter=1hr'
Mar 22 13:05:22 raspberrypi weewx[1769] INFO weewx.restx: PWSWeather: Published record 2021-03-22 13:05:00 MDT (1616439900)
Mar 22 13:05:22 raspberrypi weewxd: forecast: AerisThread: Aeris: got 24 forecast records
Mar 22 13:05:22 raspberrypi weewxd: forecast: AerisThread: Aeris: saving 24 forecast records
Mar 22 13:05:22 raspberrypi weewxd: forecast: AerisThread: Aeris: forecast failure: addRecord() got an unexpected keyword argument 'log_level'
Mar 22 13:05:22 raspberrypi weewxd: forecast: AerisThread: Aeris: terminating thread
Mar 22 13:05:22 raspberrypi weewx[1769] INFO weewx.restx: Wunderground-PWS: Published record 2021-03-22 13:05:00 MDT (1616439900)
Mar 22 13:05:24 raspberrypi weewx[1769] INFO weewx.cheetahgenerator: Generated 20 files for report StandardReport in 2.26 seconds
Mar 22 13:05:25 raspberrypi weewx[1769] INFO weewx.imagegenerator: Generated 12 images for report StandardReport in 1.04 seconds
Mar 22 13:05:25 raspberrypi weewx[1769] INFO weewx.reportengine: Copied 0 files to /var/www/html/weewx
Mar 22 13:05:27 raspberrypi weewxd: sdr: MainThread: lines=['{"time" : "2021-03-22 19:05:24", "model" : "Acurite tower sensor", "id" : 6771, "channel" : "B", "temperature_C" : 21.500, "humidity" : 33, "battery" : 0, "status" : 68}\n', '{"time" : "2021-03-22 19:05:24", "model" : "Acurite tower sensor", "id" : 6771, "channel" : "B", "temperature_C" : 21.500, "humidity" : 33, "battery" : 0, "status" : 68}\n', '{"time" : "2021-03-22 19:05:24", "model" : "Acurite tower sensor", "id" : 6771, "channel" : "B", "temperature_C" : 21.500, "humidity" : 33, "battery" : 0, "status" : 68}\n']
Mar 22 13:05:27 raspberrypi weewxd: sdr: MainThread: packet={u'extraHumid2': 33.0, u'extraTemp2': 21.5, u'txTempBatteryStatus': 0, 'usUnits': 16, 'dateTime': 1616439924}
Mar 22 13:05:27 raspberrypi weewxd: sdr: MainThread: ignoring duplicate packet {u'extraHumid2': 33.0, u'extraTemp2': 21.5, u'txTempBatteryStatus': 0, 'usUnits': 16, 'dateTime': 1616439924}
Mar 22 13:05:27 raspberrypi weewxd: sdr: MainThread: ignoring duplicate packet {u'extraHumid2': 33.0, u'extraTemp2': 21.5, u'txTempBatteryStatus': 0, 'usUnits': 16, 'dateTime': 1616439924}
My conf.
# WEEWX CONFIGURATION FILE
#
# Copyright (c) 2009-2015 Tom Keffer <tke...@gmail.com>
# See the file LICENSE.txt for your rights.
##############################################################################
# This section is for general configuration information.
# Set to 1 for extra debug info, otherwise comment it out or set to zero
debug = 0
# Root directory of the weewx data file hierarchy for this station
WEEWX_ROOT = /
# Whether to log successful operations
log_success = True
# Whether to log unsuccessful operations
log_failure = True
# How long to wait before timing out a socket (FTP, HTTP) connection
socket_timeout = 20
# Do not modify this. It is used when installing and updating weewx.
version = 4.4.0
##############################################################################
# This section is for information about the station.
[Station]
# Description of the station location
location = Kimble Backyard PWS
# Latitude and longitude in decimal degrees
latitude = 39.5468333
longitude = -104.978
# Altitude of the station, with unit it is in. This is downloaded from
# from the station if the hardware supports it.
altitude = 5745, foot
# Set to type of station hardware. There must be a corresponding stanza
# in this file with a 'driver' parameter indicating the driver to be used.
station_type = SDR
# If you have a website, you may specify an URL
#station_url = http://www.example.com
# The start of the rain year (1=January; 10=October, etc.). This is
# downloaded from the station if the hardware supports it.
rain_year_start = 1
# Start of week (0=Monday, 6=Sunday)
week_start = 6
##############################################################################
[Simulator]
# This section is for the weewx weather station simulator
# The time (in seconds) between LOOP packets.
loop_interval = 2.5
# The simulator mode can be either 'simulator' or 'generator'.
# Real-time simulator. Sleep between each LOOP packet.
mode = simulator
# Generator. Emit LOOP packets as fast as possible (useful for testing).
#mode = generator
# The start time. If not specified, the default is to use the present time.
#start = 2011-01-01 00:00
# The driver to use:
driver = weewx.drivers.simulator
##############################################################################
# This section is for uploading data to Internet sites
[StdRESTful]
[[StationRegistry]]
# To register this weather station with weewx, set this to true
register_this_station = false
[[AWEKAS]]
# This section is for configuring posts to AWEKAS.
# If you wish to do this, set the option 'enable' to true,
# and specify a username and password.
enable = false
username = replace_me
# To guard against parsing errors, put your password in quotes:
password = replace_me
[[CWOP]]
# This section is for configuring posts to CWOP.
# If you wish to do this, set the option 'enable' to true,
# and specify the station ID (e.g., CW1234).
enable = false
station = replace_me
# If this is an APRS (radio amateur) station, uncomment
# the following and replace with a passcode (e.g., 12345).
#passcode = replace_me (APRS stations only)
[[PWSweather]]
# This section is for configuring posts to PWSweather.com.
# If you wish to do this, set the option 'enable' to true,
# and specify a station and password.
enable = true
station = KCOLITTL27
# To guard against parsing errors, put your password in quotes:
password = xxxxxxxxx
[[WOW]]
# This section is for configuring posts to WOW.
# If you wish to do this, set the option 'enable' to true,
# and specify a station and password.
enable = false
station = replace_me
# To guard against parsing errors, put your password in quotes:
password = replace_me
[[Wunderground]]
# This section is for configuring posts to the Weather Underground.
# If you wish to do this, set the option 'enable' to true,
# and specify a station (e.g., 'KORHOODR3') and password.
enable = true
station = KCOLITTL270
# To guard against parsing errors, put your password in quotes:
password = xxxxxxxx
# Set the following to True to have weewx use the WU "Rapidfire"
# protocol. Not all hardware can support it. See the User's Guide.
rapidfire = false
# If you plan on using wunderfixer, set the following
# to your API key:
api_key = replace_me
##############################################################################
# This section specifies what reports, using which skins, to generate.
[StdReport]
# Where the skins reside, relative to WEEWX_ROOT
SKIN_ROOT = /etc/weewx/skins
# Where the generated reports should go, relative to WEEWX_ROOT
HTML_ROOT = /var/www/html/weewx
# The database binding indicates which data should be used in reports.
data_binding = wx_binding
####
# Each of the following subsections defines a report that will be run.
# See the customizing guide to change the units, plot types and line
# colors, modify the fonts, display additional sensor data, and other
# customizations. Many of those changes can be made here by overriding
# parameters, or by modifying templates within the skin itself.
[[StandardReport]]
# See the customizing guide to change the units, plot types and line
# colors, modify the fonts, display additional sensor data, and other
# customizations. Many of those changes can be made here by overriding
# parameters, or by modifying templates within the skin itself.
# The StandardReport uses the 'Standard' skin, which contains the
# images, templates and plots for the report.
skin = Standard
enable = True
[[[Units]]]
[[[[Groups]]]]
group_altitude = foot
group_speed2 = mile_per_hour2
group_pressure = inHg
group_rain = inch
group_rainrate = inch_per_hour
group_temperature = degree_F
group_degree_day = degree_F_day
group_speed = mile_per_hour
[[SeasonsReport]]
# The SeasonsReport uses the 'Seasons' skin, which contains the
# images, templates and plots for the report.
skin = Seasons
enable = false
[[SmartphoneReport]]
# The SmartphoneReport uses the 'Smartphone' skin, and the images and
# files are placed in a dedicated subdirectory.
skin = Smartphone
enable = false
HTML_ROOT = public_html/smartphone
[[MobileReport]]
# The MobileReport uses the 'Mobile' skin, and the images and files
# are placed in a dedicated subdirectory.
skin = Mobile
enable = false
HTML_ROOT = public_html/mobile
[[FTP]]
# FTP'ing the results to a webserver is treated as just another report,
# albeit one with an unusual report generator!
skin = Ftp
# If you wish to use FTP, uncomment and fill out the next four lines.
# user = craigk
# password = hat.777
# server = ftp.powweb.com
# path = /htdocs/weather/
# Set to True for an FTP over TLS (FTPS) connection. Not all servers
# support this.
secure_ftp = False
# To upload files from something other than what HTML_ROOT is set
# to above, specify a different HTML_ROOT here.
#HTML_ROOT = /var/www/html/weewx
# Most FTP servers use port 21
port = 21
# Set to 1 to use passive mode, zero for active mode
passive = 1
[[RSYNC]]
# rsync'ing to a webserver is treated as just another report
skin = Rsync
# If you wish to use rsync, you must configure passwordless ssh using
# public/private key authentication from the user account that weewx
# runs as to the user account on the remote machine where the files
# will be copied.
#
# The following three lines determine where files will be sent.
#server = replace with the rsync server name, e.g, www.threefools.org
#path = replace with the rsync destination directory (e.g., /weather)
#user = replace with the rsync username
# Rsync can be configured to remove files from the remote server if
# they don't exist under HTML_ROOT locally. USE WITH CAUTION: if you
# make a mistake in the remote path, you could could unintentionally
# cause unrelated files to be deleted. Set to 1 to enable remote file
# deletion, zero to allow files to accumulate remotely.
delete = 0
####
# Various options for customizing your reports.
[[Defaults]]
# The following section determines the selection and formatting of units.
[[[Units]]]
# The following section sets what unit to use for each unit group.
# NB: The unit is always in the singular. I.e., 'mile_per_hour',
# NOT 'miles_per_hour'
[[[[Groups]]]]
group_altitude = foot # Options are 'foot' or 'meter'
group_degree_day = degree_F_day # Options are 'degree_F_day' or 'degree_C_day'
group_distance = mile # Options are 'mile' or 'km'
group_pressure = inHg # Options are 'inHg', 'mmHg', 'mbar', or 'hPa'
group_rain = inch # Options are 'inch', 'cm', or 'mm'
group_rainrate = inch_per_hour # Options are 'inch_per_hour', 'cm_per_hour', or 'mm_per_hour'
group_speed = mile_per_hour # Options are 'mile_per_hour', 'km_per_hour', 'knot', or 'meter_per_second'
group_speed2 = mile_per_hour2 # Options are 'mile_per_hour2', 'km_per_hour2', 'knot2', or 'meter_per_second2'
group_temperature = degree_F # Options are 'degree_F' or 'degree_C'
# The following section sets the formatting for each type of unit.
[[[[StringFormats]]]]
centibar = %.0f
cm = %.2f
cm_per_hour = %.2f
degree_C = %.1f
degree_F = %.1f
degree_compass = %.0f
foot = %.0f
hPa = %.1f
hour = %.1f
inHg = %.3f
inch = %.2f
inch_per_hour = %.2f
km_per_hour = %.0f
km_per_hour2 = %.1f
knot = %.0f
knot2 = %.1f
mbar = %.1f
meter = %.0f
meter_per_second = %.1f
meter_per_second2 = %.1f
mile_per_hour = %.0f
mile_per_hour2 = %.1f
mm = %.1f
mmHg = %.1f
mm_per_hour = %.1f
percent = %.0f
second = %.0f
uv_index = %.1f
volt = %.1f
watt_per_meter_squared = %.0f
NONE = " N/A"
# The following section sets the label to be used for each type of unit
[[[[Labels]]]]
day = " day", " days"
hour = " hour", " hours"
minute = " minute", " minutes"
second = " second", " seconds"
NONE = ""
# The following section sets the format to be used for each time scale.
# The values below will work in every locale, but they may not look
# particularly attractive. See the Customization Guide for alternatives.
[[[[TimeFormats]]]]
hour = %H:%M
day = %X
week = %X (%A)
month = %x %X
year = %x %X
rainyear = %x %X
current = %x %X
ephem_day = %X
ephem_year = %x %X
[[[[Ordinates]]]]
# Ordinal directions. The last one should be for no wind direction
directions = N, NNE, NE, ENE, E, ESE, SE, SSE, S, SSW, SW, WSW, W, WNW, NW, NNW, N/A
# The following section sets the base temperatures used for the
# calculation of heating and cooling degree-days.
[[[[DegreeDays]]]]
# Base temperature for heating days, with unit:
heating_base = 65, degree_F
# Base temperature for cooling days, with unit:
cooling_base = 65, degree_F
# Base temperature for growing days, with unit:
growing_base = 50.0, degree_F
# A trend takes a difference across a time period. The following
# section sets the time period, and how big an error is allowed to
# still be counted as the start or end of a period.
[[[[Trend]]]]
time_delta = 10800 # 3 hours
time_grace = 300 # 5 minutes
# The labels to be used for each observation type
[[[Labels]]]
# Set to hemisphere abbreviations suitable for your location:
hemispheres = N, S, E, W
# Formats to be used for latitude whole degrees, longitude whole
# degrees, and minutes:
latlon_formats = %02d, %03d, %05.2f
# Generic labels, keyed by an observation type.
[[[[Generic]]]]
barometer = Barometer
dewpoint = Dew Point
ET = ET
heatindex = Heat Index
inHumidity = Inside Humidity
inTemp = Bedroom Temp
outHumidity = Humidity
outTemp = Outside Temperature
radiation = Radiation
rain = Rain
rainRate = Rain Rate
UV = UV Index
windDir = Wind Direction
windGust = Gust Speed
windGustDir = Gust Direction
windSpeed = Wind Speed
windchill = Wind Chill
windgustvec = Gust Vector
windvec = Wind Vector
extraTemp1 = Loft Temp
extraTemp2 = Kitchen Temp
extraTemp3 = Temperature3
# Sensor status indicators
rxCheckPercent = Signal Quality
txBatteryStatus = Transmitter Battery
windBatteryStatus = Wind Battery
rainBatteryStatus = Rain Battery
outTempBatteryStatus = Outside Temperature Battery
inTempBatteryStatus = Inside Temperature Battery
consBatteryVoltage = Console Battery
heatingVoltage = Heating Battery
supplyVoltage = Supply Voltage
referenceVoltage = Reference Voltage
[[[Almanac]]]
# The labels to be used for the phases of the moon:
moon_phases = New, Waxing crescent, First quarter, Waxing gibbous, Full, Waning gibbous, Last quarter, Waning crescent
##############################################################################
# This service acts as a filter, converting the unit system coming from
# the hardware to a unit system in the database.
[StdConvert]
# The target_unit affects only the unit system in the database. Once
# chosen it cannot be changed without converting the entire database.
# Modification of target_unit after starting weewx will result in
# corrupt data - the database will contain a mix of US and METRIC data.
#
# The value of target_unit does not affect the unit system for
# reporting - reports can display US, Metric, or any combination of units.
#
# In most cases, target_unit should be left as the default: US
#
# In particular, those migrating from a standard wview installation
# should use US since that is what the wview database contains.
# DO NOT MODIFY THIS VALUE UNLESS YOU KNOW WHAT YOU ARE DOING!
target_unit = US # Options are 'US', 'METRICWX', or 'METRIC'
##############################################################################
# This section can adjust data using calibration expressions.
[StdCalibrate]
[[Corrections]]
# For each type, an arbitrary calibration expression can be given.
# It should be in the units defined in the StdConvert section.
# Example:
foo = foo + 0.2
# outTemp = outTemp - 1
##############################################################################
# This section is for quality control checks. If units are not specified,
# values must be in the units defined in the StdConvert section.
[StdQC]
[[MinMax]]
barometer = 26, 32.5, inHg
outTemp = -40, 120, degree_F
inTemp = 10, 120, degree_F
outHumidity = 0, 100
inHumidity = 0, 100
windSpeed = 0, 120, mile_per_hour
windGust = 0, 120, mile_per_hour
pressure = 24, 34.5, inHg
##############################################################################
# This section controls the origin of derived values.
[StdWXCalculate]
[[Calculations]]
# Derived quantities are calculated by this service. Possible values are:
# hardware - use the value provided by hardware
# software - use the value calculated by weewx
# prefer_hardware - use value provide by hardware if available,
# otherwise use value calculated by weewx
pressure = prefer_hardware
barometer = prefer_hardware
altimeter = prefer_hardware
windchill = prefer_hardware
heatindex = prefer_hardware
dewpoint = prefer_hardware
inDewpoint = prefer_hardware
rainRate = prefer_hardware
maxSolarRad = prefer_hardware
cloudbase = prefer_hardware
humidex = prefer_hardware
appTemp = prefer_hardware
ET = prefer_hardware
windrun = prefer_hardware
##############################################################################
# For hardware that supports it, this section controls how often the
# onboard clock gets updated.
[StdTimeSynch]
# How often to check the weather station clock for drift (in seconds)
clock_check = 14400
# How much it can drift before we will correct it (in seconds)
max_drift = 5
##############################################################################
# This section is for configuring the archive service.
[StdArchive]
# If the station hardware supports data logging then the archive interval
# will be downloaded from the station. Otherwise, specify it (in seconds).
archive_interval = 300
# If possible, new archive records are downloaded from the station
# hardware. If the hardware does not support this, then new archive
# records will be generated in software.
# Set the following to "software" to force software record generation.
record_generation = hardware
# Whether to include LOOP data in hi/low statistics
loop_hilo = True
# The data binding used to save archive records
data_binding = wx_binding
##############################################################################
# This section binds a data store to a database.
[DataBindings]
[[wx_binding]]
# The database must match one of the sections in [Databases].
# This is likely to be the only option you would want to change.
database = archive_sqlite
# The name of the table within the database
table_name = archive
# The manager handles aggregation of data for historical summaries
manager = weewx.wxmanager.WXDaySummaryManager
# The schema defines the structure of the database.
# It is *only* used when the database is created.
schema = schemas.wview.schema
[[forecast_binding]]
database = forecast_sqlite
##############################################################################
# This section defines various databases.
[Databases]
# A SQLite database is simply a single file
[[archive_sqlite]]
database_type = SQLite
database_name = weewx.sdb
# MySQL
[[archive_mysql]]
database_type = MySQL
database_name = weewx
[[forecast_sqlite]]
database_name = forecast.sdb
database_type = SQLite
##############################################################################
# This section defines defaults for the different types of databases.
[DatabaseTypes]
# Defaults for SQLite databases
[[SQLite]]
driver = weedb.sqlite
# Directory in which the database files are located
SQLITE_ROOT = /var/lib/weewx
# Defaults for MySQL databases
[[MySQL]]
driver = weedb.mysql
# The host where the database is located
host = localhost
# The user name for logging in to the host
user = weewx
# The password for the user name. Put in quotes to guard against parsing errors.
password = weewx
##############################################################################
# This section configures the internal weewx engine.
[Engine]
# The following section specifies which services should be run and in what order.
[[Services]]
prep_services = weewx.engine.StdTimeSynch
data_services = user.pond.PondService
process_services = weewx.engine.StdConvert, weewx.engine.StdCalibrate, weewx.engine.StdQC, weewx.wxservices.StdWXCalculate
xtype_services = weewx.wxxtypes.StdWXXTypes, weewx.wxxtypes.StdPressureCooker, weewx.wxxtypes.StdRainRater, weewx.wxxtypes.StdDelta
archive_services = weewx.engine.StdArchive, user.forecast.ZambrettiForecast, user.forecast.AerisForecast
restful_services = weewx.restx.StdStationRegistry, weewx.restx.StdWunderground, weewx.restx.StdPWSweather, weewx.restx.StdCWOP, weewx.restx.StdWOW, weewx.restx.StdAWEKAS
report_services = weewx.engine.StdPrint, weewx.engine.StdReport
############################################################################
[SDR]
# collect data from Acurite 5n1 sensor 052B and 2E2F Tower
# The driver to use
driver = user.sdr
cmd = rtl_433 -q -U -F json -R 40
[[sensor_map]]
windDir = wind_dir.052B.Acurite5n1Packet
windSpeed = wind_speed.052B.Acurite5n1Packet
outTemp = temperature.052B.Acurite5n1Packet
outHumidity = humidity.052B.Acurite5n1Packet
rain_total = rain_total.052B.Acurite5n1Packet
outTempBatteryStatus = battery.052B.Acurite5n1Packet
inTemp = temperature.2E2F.AcuriteTowerPacket
inHumidity = humidity.2E2F.AcuriteTowerPacket
inTempBatteryStatus = battery.2E2F.AcuriteTowerPacket
extraTemp2 = temperature.1A73.AcuriteTowerPacket
extraHumid2 = humidity.1A73.AcuriteTowerPacket
txTempBatteryStatus = battery.1A73.AcuriteTowerPacket
##############################################################################
# Options for extension 'forecast'
[Forecast]
data_binding = forecast_binding
[[OWM]]
api_key = INSERT_OWM_API_KEY_HERE
[[WWO]]
api_key = INSERT_WWO_API_KEY_HERE
[[WU]]
api_key = INSERT_WU_API_KEY_HERE
[[NWS]]
lid = INSERT_lid_HERE
foid = INSERT_foid_HERE
[[UKMO]]
api_key = INSERT_UKMO_API_KEY_HERE
location = INSERT_UK_LOCATION_HERE
[[XTide]]
location = "INSERT_LOCATION_HERE (e.g., Boston)"
[[Zambretti]]
hemisphere = NORTH
[[Aeris]]
client_secret =xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
client_id = xxxxxxxxxxxxxxxxxxxxxxxxxxx
#
# Copyright (c) 2009-2015 Tom Keffer <tke...@gmail.com>
# See the file LICENSE.txt for your rights.
##############################################################################
# This section is for general configuration information.
# Set to 1 for extra debug info, otherwise comment it out or set to zero
debug = 0
# Root directory of the weewx data file hierarchy for this station
WEEWX_ROOT = /
# Whether to log successful operations
log_success = True
# Whether to log unsuccessful operations
log_failure = True
# How long to wait before timing out a socket (FTP, HTTP) connection
socket_timeout = 20
# Do not modify this. It is used when installing and updating weewx.
version = 4.4.0
##############################################################################
# This section is for information about the station.
[Station]
# Description of the station location
location = Kimble Backyard PWS
# Latitude and longitude in decimal degrees
latitude = 39.5468333
longitude = -104.978
# Altitude of the station, with unit it is in. This is downloaded from
# from the station if the hardware supports it.
altitude = 5745, foot
# Set to type of station hardware. There must be a corresponding stanza
# in this file with a 'driver' parameter indicating the driver to be used.
station_type = SDR
# If you have a website, you may specify an URL
#station_url = http://www.example.com
# The start of the rain year (1=January; 10=October, etc.). This is
# downloaded from the station if the hardware supports it.
rain_year_start = 1
# Start of week (0=Monday, 6=Sunday)
week_start = 6
##############################################################################
[Simulator]
# This section is for the weewx weather station simulator
# The time (in seconds) between LOOP packets.
loop_interval = 2.5
# The simulator mode can be either 'simulator' or 'generator'.
# Real-time simulator. Sleep between each LOOP packet.
mode = simulator
# Generator. Emit LOOP packets as fast as possible (useful for testing).
#mode = generator
# The start time. If not specified, the default is to use the present time.
#start = 2011-01-01 00:00
# The driver to use:
driver = weewx.drivers.simulator
##############################################################################
# This section is for uploading data to Internet sites
[StdRESTful]
[[StationRegistry]]
# To register this weather station with weewx, set this to true
register_this_station = false
[[AWEKAS]]
# This section is for configuring posts to AWEKAS.
# If you wish to do this, set the option 'enable' to true,
# and specify a username and password.
enable = false
username = replace_me
# To guard against parsing errors, put your password in quotes:
password = replace_me
[[CWOP]]
# This section is for configuring posts to CWOP.
# If you wish to do this, set the option 'enable' to true,
# and specify the station ID (e.g., CW1234).
enable = false
station = replace_me
# If this is an APRS (radio amateur) station, uncomment
# the following and replace with a passcode (e.g., 12345).
#passcode = replace_me (APRS stations only)
[[PWSweather]]
# This section is for configuring posts to PWSweather.com.
# If you wish to do this, set the option 'enable' to true,
# and specify a station and password.
enable = true
station = KCOLITTL27
# To guard against parsing errors, put your password in quotes:
password = xxxxxxxxx
[[WOW]]
# This section is for configuring posts to WOW.
# If you wish to do this, set the option 'enable' to true,
# and specify a station and password.
enable = false
station = replace_me
# To guard against parsing errors, put your password in quotes:
password = replace_me
[[Wunderground]]
# This section is for configuring posts to the Weather Underground.
# If you wish to do this, set the option 'enable' to true,
# and specify a station (e.g., 'KORHOODR3') and password.
enable = true
station = KCOLITTL270
# To guard against parsing errors, put your password in quotes:
password = xxxxxxxx
# Set the following to True to have weewx use the WU "Rapidfire"
# protocol. Not all hardware can support it. See the User's Guide.
rapidfire = false
# If you plan on using wunderfixer, set the following
# to your API key:
api_key = replace_me
##############################################################################
# This section specifies what reports, using which skins, to generate.
[StdReport]
# Where the skins reside, relative to WEEWX_ROOT
SKIN_ROOT = /etc/weewx/skins
# Where the generated reports should go, relative to WEEWX_ROOT
HTML_ROOT = /var/www/html/weewx
# The database binding indicates which data should be used in reports.
data_binding = wx_binding
####
# Each of the following subsections defines a report that will be run.
# See the customizing guide to change the units, plot types and line
# colors, modify the fonts, display additional sensor data, and other
# customizations. Many of those changes can be made here by overriding
# parameters, or by modifying templates within the skin itself.
[[StandardReport]]
# See the customizing guide to change the units, plot types and line
# colors, modify the fonts, display additional sensor data, and other
# customizations. Many of those changes can be made here by overriding
# parameters, or by modifying templates within the skin itself.
# The StandardReport uses the 'Standard' skin, which contains the
# images, templates and plots for the report.
skin = Standard
enable = True
[[[Units]]]
[[[[Groups]]]]
group_altitude = foot
group_speed2 = mile_per_hour2
group_pressure = inHg
group_rain = inch
group_rainrate = inch_per_hour
group_temperature = degree_F
group_degree_day = degree_F_day
group_speed = mile_per_hour
[[SeasonsReport]]
# The SeasonsReport uses the 'Seasons' skin, which contains the
# images, templates and plots for the report.
skin = Seasons
enable = false
[[SmartphoneReport]]
# The SmartphoneReport uses the 'Smartphone' skin, and the images and
# files are placed in a dedicated subdirectory.
skin = Smartphone
enable = false
HTML_ROOT = public_html/smartphone
[[MobileReport]]
# The MobileReport uses the 'Mobile' skin, and the images and files
# are placed in a dedicated subdirectory.
skin = Mobile
enable = false
HTML_ROOT = public_html/mobile
[[FTP]]
# FTP'ing the results to a webserver is treated as just another report,
# albeit one with an unusual report generator!
skin = Ftp
# If you wish to use FTP, uncomment and fill out the next four lines.
# user = craigk
# password = hat.777
# server = ftp.powweb.com
# path = /htdocs/weather/
# Set to True for an FTP over TLS (FTPS) connection. Not all servers
# support this.
secure_ftp = False
# To upload files from something other than what HTML_ROOT is set
# to above, specify a different HTML_ROOT here.
#HTML_ROOT = /var/www/html/weewx
# Most FTP servers use port 21
port = 21
# Set to 1 to use passive mode, zero for active mode
passive = 1
[[RSYNC]]
# rsync'ing to a webserver is treated as just another report
skin = Rsync
# If you wish to use rsync, you must configure passwordless ssh using
# public/private key authentication from the user account that weewx
# runs as to the user account on the remote machine where the files
# will be copied.
#
# The following three lines determine where files will be sent.
#server = replace with the rsync server name, e.g, www.threefools.org
#path = replace with the rsync destination directory (e.g., /weather)
#user = replace with the rsync username
# Rsync can be configured to remove files from the remote server if
# they don't exist under HTML_ROOT locally. USE WITH CAUTION: if you
# make a mistake in the remote path, you could could unintentionally
# cause unrelated files to be deleted. Set to 1 to enable remote file
# deletion, zero to allow files to accumulate remotely.
delete = 0
####
# Various options for customizing your reports.
[[Defaults]]
# The following section determines the selection and formatting of units.
[[[Units]]]
# The following section sets what unit to use for each unit group.
# NB: The unit is always in the singular. I.e., 'mile_per_hour',
# NOT 'miles_per_hour'
[[[[Groups]]]]
group_altitude = foot # Options are 'foot' or 'meter'
group_degree_day = degree_F_day # Options are 'degree_F_day' or 'degree_C_day'
group_distance = mile # Options are 'mile' or 'km'
group_pressure = inHg # Options are 'inHg', 'mmHg', 'mbar', or 'hPa'
group_rain = inch # Options are 'inch', 'cm', or 'mm'
group_rainrate = inch_per_hour # Options are 'inch_per_hour', 'cm_per_hour', or 'mm_per_hour'
group_speed = mile_per_hour # Options are 'mile_per_hour', 'km_per_hour', 'knot', or 'meter_per_second'
group_speed2 = mile_per_hour2 # Options are 'mile_per_hour2', 'km_per_hour2', 'knot2', or 'meter_per_second2'
group_temperature = degree_F # Options are 'degree_F' or 'degree_C'
# The following section sets the formatting for each type of unit.
[[[[StringFormats]]]]
centibar = %.0f
cm = %.2f
cm_per_hour = %.2f
degree_C = %.1f
degree_F = %.1f
degree_compass = %.0f
foot = %.0f
hPa = %.1f
hour = %.1f
inHg = %.3f
inch = %.2f
inch_per_hour = %.2f
km_per_hour = %.0f
km_per_hour2 = %.1f
knot = %.0f
knot2 = %.1f
mbar = %.1f
meter = %.0f
meter_per_second = %.1f
meter_per_second2 = %.1f
mile_per_hour = %.0f
mile_per_hour2 = %.1f
mm = %.1f
mmHg = %.1f
mm_per_hour = %.1f
percent = %.0f
second = %.0f
uv_index = %.1f
volt = %.1f
watt_per_meter_squared = %.0f
NONE = " N/A"
# The following section sets the label to be used for each type of unit
[[[[Labels]]]]
day = " day", " days"
hour = " hour", " hours"
minute = " minute", " minutes"
second = " second", " seconds"
NONE = ""
# The following section sets the format to be used for each time scale.
# The values below will work in every locale, but they may not look
# particularly attractive. See the Customization Guide for alternatives.
[[[[TimeFormats]]]]
hour = %H:%M
day = %X
week = %X (%A)
month = %x %X
year = %x %X
rainyear = %x %X
current = %x %X
ephem_day = %X
ephem_year = %x %X
[[[[Ordinates]]]]
# Ordinal directions. The last one should be for no wind direction
directions = N, NNE, NE, ENE, E, ESE, SE, SSE, S, SSW, SW, WSW, W, WNW, NW, NNW, N/A
# The following section sets the base temperatures used for the
# calculation of heating and cooling degree-days.
[[[[DegreeDays]]]]
# Base temperature for heating days, with unit:
heating_base = 65, degree_F
# Base temperature for cooling days, with unit:
cooling_base = 65, degree_F
# Base temperature for growing days, with unit:
growing_base = 50.0, degree_F
# A trend takes a difference across a time period. The following
# section sets the time period, and how big an error is allowed to
# still be counted as the start or end of a period.
[[[[Trend]]]]
time_delta = 10800 # 3 hours
time_grace = 300 # 5 minutes
# The labels to be used for each observation type
[[[Labels]]]
# Set to hemisphere abbreviations suitable for your location:
hemispheres = N, S, E, W
# Formats to be used for latitude whole degrees, longitude whole
# degrees, and minutes:
latlon_formats = %02d, %03d, %05.2f
# Generic labels, keyed by an observation type.
[[[[Generic]]]]
barometer = Barometer
dewpoint = Dew Point
ET = ET
heatindex = Heat Index
inHumidity = Inside Humidity
inTemp = Bedroom Temp
outHumidity = Humidity
outTemp = Outside Temperature
radiation = Radiation
rain = Rain
rainRate = Rain Rate
UV = UV Index
windDir = Wind Direction
windGust = Gust Speed
windGustDir = Gust Direction
windSpeed = Wind Speed
windchill = Wind Chill
windgustvec = Gust Vector
windvec = Wind Vector
extraTemp1 = Loft Temp
extraTemp2 = Kitchen Temp
extraTemp3 = Temperature3
# Sensor status indicators
rxCheckPercent = Signal Quality
txBatteryStatus = Transmitter Battery
windBatteryStatus = Wind Battery
rainBatteryStatus = Rain Battery
outTempBatteryStatus = Outside Temperature Battery
inTempBatteryStatus = Inside Temperature Battery
consBatteryVoltage = Console Battery
heatingVoltage = Heating Battery
supplyVoltage = Supply Voltage
referenceVoltage = Reference Voltage
[[[Almanac]]]
# The labels to be used for the phases of the moon:
moon_phases = New, Waxing crescent, First quarter, Waxing gibbous, Full, Waning gibbous, Last quarter, Waning crescent
##############################################################################
# This service acts as a filter, converting the unit system coming from
# the hardware to a unit system in the database.
[StdConvert]
# The target_unit affects only the unit system in the database. Once
# chosen it cannot be changed without converting the entire database.
# Modification of target_unit after starting weewx will result in
# corrupt data - the database will contain a mix of US and METRIC data.
#
# The value of target_unit does not affect the unit system for
# reporting - reports can display US, Metric, or any combination of units.
#
# In most cases, target_unit should be left as the default: US
#
# In particular, those migrating from a standard wview installation
# should use US since that is what the wview database contains.
# DO NOT MODIFY THIS VALUE UNLESS YOU KNOW WHAT YOU ARE DOING!
target_unit = US # Options are 'US', 'METRICWX', or 'METRIC'
##############################################################################
# This section can adjust data using calibration expressions.
[StdCalibrate]
[[Corrections]]
# For each type, an arbitrary calibration expression can be given.
# It should be in the units defined in the StdConvert section.
# Example:
foo = foo + 0.2
# outTemp = outTemp - 1
##############################################################################
# This section is for quality control checks. If units are not specified,
# values must be in the units defined in the StdConvert section.
[StdQC]
[[MinMax]]
barometer = 26, 32.5, inHg
outTemp = -40, 120, degree_F
inTemp = 10, 120, degree_F
outHumidity = 0, 100
inHumidity = 0, 100
windSpeed = 0, 120, mile_per_hour
windGust = 0, 120, mile_per_hour
pressure = 24, 34.5, inHg
##############################################################################
# This section controls the origin of derived values.
[StdWXCalculate]
[[Calculations]]
# Derived quantities are calculated by this service. Possible values are:
# hardware - use the value provided by hardware
# software - use the value calculated by weewx
# prefer_hardware - use value provide by hardware if available,
# otherwise use value calculated by weewx
pressure = prefer_hardware
barometer = prefer_hardware
altimeter = prefer_hardware
windchill = prefer_hardware
heatindex = prefer_hardware
dewpoint = prefer_hardware
inDewpoint = prefer_hardware
rainRate = prefer_hardware
maxSolarRad = prefer_hardware
cloudbase = prefer_hardware
humidex = prefer_hardware
appTemp = prefer_hardware
ET = prefer_hardware
windrun = prefer_hardware
##############################################################################
# For hardware that supports it, this section controls how often the
# onboard clock gets updated.
[StdTimeSynch]
# How often to check the weather station clock for drift (in seconds)
clock_check = 14400
# How much it can drift before we will correct it (in seconds)
max_drift = 5
##############################################################################
# This section is for configuring the archive service.
[StdArchive]
# If the station hardware supports data logging then the archive interval
# will be downloaded from the station. Otherwise, specify it (in seconds).
archive_interval = 300
# If possible, new archive records are downloaded from the station
# hardware. If the hardware does not support this, then new archive
# records will be generated in software.
# Set the following to "software" to force software record generation.
record_generation = hardware
# Whether to include LOOP data in hi/low statistics
loop_hilo = True
# The data binding used to save archive records
data_binding = wx_binding
##############################################################################
# This section binds a data store to a database.
[DataBindings]
[[wx_binding]]
# The database must match one of the sections in [Databases].
# This is likely to be the only option you would want to change.
database = archive_sqlite
# The name of the table within the database
table_name = archive
# The manager handles aggregation of data for historical summaries
manager = weewx.wxmanager.WXDaySummaryManager
# The schema defines the structure of the database.
# It is *only* used when the database is created.
schema = schemas.wview.schema
[[forecast_binding]]
database = forecast_sqlite
##############################################################################
# This section defines various databases.
[Databases]
# A SQLite database is simply a single file
[[archive_sqlite]]
database_type = SQLite
database_name = weewx.sdb
# MySQL
[[archive_mysql]]
database_type = MySQL
database_name = weewx
[[forecast_sqlite]]
database_name = forecast.sdb
database_type = SQLite
##############################################################################
# This section defines defaults for the different types of databases.
[DatabaseTypes]
# Defaults for SQLite databases
[[SQLite]]
driver = weedb.sqlite
# Directory in which the database files are located
SQLITE_ROOT = /var/lib/weewx
# Defaults for MySQL databases
[[MySQL]]
driver = weedb.mysql
# The host where the database is located
host = localhost
# The user name for logging in to the host
user = weewx
# The password for the user name. Put in quotes to guard against parsing errors.
password = weewx
##############################################################################
# This section configures the internal weewx engine.
[Engine]
# The following section specifies which services should be run and in what order.
[[Services]]
prep_services = weewx.engine.StdTimeSynch
data_services = user.pond.PondService
process_services = weewx.engine.StdConvert, weewx.engine.StdCalibrate, weewx.engine.StdQC, weewx.wxservices.StdWXCalculate
xtype_services = weewx.wxxtypes.StdWXXTypes, weewx.wxxtypes.StdPressureCooker, weewx.wxxtypes.StdRainRater, weewx.wxxtypes.StdDelta
archive_services = weewx.engine.StdArchive, user.forecast.ZambrettiForecast, user.forecast.AerisForecast
restful_services = weewx.restx.StdStationRegistry, weewx.restx.StdWunderground, weewx.restx.StdPWSweather, weewx.restx.StdCWOP, weewx.restx.StdWOW, weewx.restx.StdAWEKAS
report_services = weewx.engine.StdPrint, weewx.engine.StdReport
############################################################################
[SDR]
# collect data from Acurite 5n1 sensor 052B and 2E2F Tower
# The driver to use
driver = user.sdr
cmd = rtl_433 -q -U -F json -R 40
[[sensor_map]]
windDir = wind_dir.052B.Acurite5n1Packet
windSpeed = wind_speed.052B.Acurite5n1Packet
outTemp = temperature.052B.Acurite5n1Packet
outHumidity = humidity.052B.Acurite5n1Packet
rain_total = rain_total.052B.Acurite5n1Packet
outTempBatteryStatus = battery.052B.Acurite5n1Packet
inTemp = temperature.2E2F.AcuriteTowerPacket
inHumidity = humidity.2E2F.AcuriteTowerPacket
inTempBatteryStatus = battery.2E2F.AcuriteTowerPacket
extraTemp2 = temperature.1A73.AcuriteTowerPacket
extraHumid2 = humidity.1A73.AcuriteTowerPacket
txTempBatteryStatus = battery.1A73.AcuriteTowerPacket
##############################################################################
# Options for extension 'forecast'
[Forecast]
data_binding = forecast_binding
[[OWM]]
api_key = INSERT_OWM_API_KEY_HERE
[[WWO]]
api_key = INSERT_WWO_API_KEY_HERE
[[WU]]
api_key = INSERT_WU_API_KEY_HERE
[[NWS]]
lid = INSERT_lid_HERE
foid = INSERT_foid_HERE
[[UKMO]]
api_key = INSERT_UKMO_API_KEY_HERE
location = INSERT_UK_LOCATION_HERE
[[XTide]]
location = "INSERT_LOCATION_HERE (e.g., Boston)"
[[Zambretti]]
hemisphere = NORTH
[[Aeris]]
client_secret =xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
client_id = xxxxxxxxxxxxxxxxxxxxxxxxxxx
John Kline
Mar 22, 2021, 6:13:52 PM3/22/21
to weewx...@googlegroups.com
For forecast in WeeWX 4.x, you should have better luck installing:
On Mar 22, 2021, at 1:18 PM, craig....@gmail.com <craig....@gmail.com> wrote:
--
You received this message because you are subscribed to the Google Groups "weewx-user" group.
To unsubscribe from this group and stop receiving emails from it, send an email to weewx-user+...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/292d5f0b-2148-410d-b8d3-fe72d7d0e015n%40googlegroups.com.
craig....@gmail.com
Mar 23, 2021, 5:17:32 PM3/23/21
to weewx-user
That helped with the forecast extension. Thank you!
Reply all
Reply to author
Forward
0 new messages