Issues when flashing some two gang TXT2EU Sonoff switches
Emmanuel Chryssagis
Hello.
I flashed more than 20pcs of Sonoff wall switches (TX T1EU & T2EU two gang model) with Tasmota 12.0.1. Lately I had the following problem.
In some units the second
touch pad was working perfectly but the first touch pads is not
responding although when I a pressing the touch pad sensor this is
recognized with a beep sound.
Please note that I used the same setup with the switches that don't have a problem.
All problematic units (totally 3) are working properly when they are controlled through Wi-Fi by TASMOTROL Dashboard installed on my mobile.
Any suggestion?
Emmanuel
Philip Knowles
Sent: Saturday, August 13, 2022 7:23:45 AM
To: TasmotaUsers <sonof...@googlegroups.com>
Subject: Issues when flashing some two gang TXT2EU Sonoff switches
You received this message because you are subscribed to the Google Groups "TasmotaUsers" group.
To unsubscribe from this group and stop receiving emails from it, send an email to sonoffusers...@googlegroups.com.
To view this discussion on the web, visit https://groups.google.com/d/msgid/sonoffusers/5ea20c03-b806-4e7c-9b85-38ed5a10be55n%40googlegroups.com.
man.ch...@gmail.com
Good morning Philip. I just checked all my boards single or double gang and they are all the same T1EU TOUCH V 1.0 2018.10.03.
Regards
Emmanuel
Philip Knowles
If the outputs are working there must be an issue with GPIOs on the input or the numbering.
Can you upload a screenshot of the Module Configuration page. If you are using a Template that page too.
Sent from Mail for Windows
From: man.ch...@gmail.com
Sent: 13 August 2022 08:41
To: Philip Knowles; TasmotaUsers
Subject: RE: Issues when flashing some two gang TXT2EU Sonoff switches
Good morning Philip. I just checked all my boards single or double gang and they are all the same T1EU TOUCH V 1.0 2018.10.03.
Regards
Emmanuel
From: Philip Knowles <knowles...@gmail.com>
Sent: Saturday, 13 August, 2022 09:41
To: Emmanuel Chryssagis <man.ch...@gmail.com>; TasmotaUsers <sonof...@googlegroups.com>
Subject: Re: Issues when flashing some two gang TXT2EU Sonoff switches
First thing is to check the revision number on the circuit boards.
If there's a hardware change no amount of guessing will help.
Emmanuel Chryssagis
Jéro
To view this discussion on the web, visit https://groups.google.com/d/msgid/sonoffusers/c0dfc6a7-23d5-4d6f-97c8-eda5bd401578n%40googlegroups.com.
Emmanuel Chryssagis
Philip Knowles
To: TasmotaUsers <sonof...@googlegroups.com>
man.ch...@gmail.com
Sorry . You are right. Attached is the OTHER menu. Pls note that I have tried both with the Template ACTIVATED and non ACTIVATED without any difference.
Emmanuel
From: Philip Knowles <knowles...@gmail.com>
Sent: Monday, 15 August, 2022 08:18
To: Emmanuel Chryssagis <man.ch...@gmail.com>; TasmotaUsers <sonof...@googlegroups.com>
Subject: Re: Issues when flashing some two gang TXT2EU Sonoff switches
You have still missed the Configure Other page. It looks like you have a Template entered but I don't know if it is activated
From: sonof...@googlegroups.com <sonof...@googlegroups.com> on behalf of Emmanuel Chryssagis <man.ch...@gmail.com>
Sent: Monday, August 15, 2022 6:03:09 AM
To: TasmotaUsers <sonof...@googlegroups.com>
Subject: Re: Issues when flashing some two gang TXT2EU Sonoff switches
Philip these are the menus you requested.
Comparing the similar menus that j.ch...@gmail.com send us further up the only difference I have noticed is that my Tasmota version is 12.0.2 than version 8.4.0 .
I am thinking to try to flash my sonoff switches with a previous Tasmota version.
j.ch...@gmail.com Please note that I managed to flash more than 20 switches before the problem arise. That's why I am stuck ....
On Sunday, August 14, 2022 at 9:59:47 PM UTC+3 j.ch...@gmail.com wrote:
Le dim. 14 août 2022 à 20:53, Jéro <j.ch...@gmail.com> a écrit :
Hello,
I use 5 sonoff T2 EU for my covers without problem. I use an old version because binaries released didn't include cover option but gpios could be same.
my config is :
Regards,
Le sam. 13 août 2022 à 21:13, Emmanuel Chryssagis <man.ch...@gmail.com> a écrit :
These are the screens you requested.
man.ch...@gmail.com
Philip I forgot to mention that I was experimenting with the code (numbers) in the top menu in the OTHER by trying to change the code addresses. I managed to control channel 1 from the second touch pad but nothing more. It is like the channel 1 touch pad is dead for control but as I mentioned it is responding with a beep when I touch it for long periods.
Emmanuel
From: Philip Knowles <knowles...@gmail.com>
Sent: Monday, 15 August, 2022 08:18
To: Emmanuel Chryssagis <man.ch...@gmail.com>; TasmotaUsers <sonof...@googlegroups.com>
Subject: Re: Issues when flashing some two gang TXT2EU Sonoff switches
You have still missed the Configure Other page. It looks like you have a Template entered but I don't know if it is activated
From: sonof...@googlegroups.com <sonof...@googlegroups.com> on behalf of Emmanuel Chryssagis <man.ch...@gmail.com>
Sent: Monday, August 15, 2022 6:03:09 AM
To: TasmotaUsers <sonof...@googlegroups.com>
Subject: Re: Issues when flashing some two gang TXT2EU Sonoff switches
Philip these are the menus you requested.
Comparing the similar menus that j.ch...@gmail.com send us further up the only difference I have noticed is that my Tasmota version is 12.0.2 than version 8.4.0 .
I am thinking to try to flash my sonoff switches with a previous Tasmota version.
j.ch...@gmail.com Please note that I managed to flash more than 20 switches before the problem arise. That's why I am stuck ....
On Sunday, August 14, 2022 at 9:59:47 PM UTC+3 j.ch...@gmail.com wrote:
Le dim. 14 août 2022 à 20:53, Jéro <j.ch...@gmail.com> a écrit :
Hello,
I use 5 sonoff T2 EU for my covers without problem. I use an old version because binaries released didn't include cover option but gpios could be same.
my config is :
Regards,
Le sam. 13 août 2022 à 21:13, Emmanuel Chryssagis <man.ch...@gmail.com> a écrit :
These are the screens you requested.
Philip Knowles
Sent: Monday, August 15, 2022 6:32:45 AM
To: 'Philip Knowles' <knowles...@gmail.com>; 'TasmotaUsers' <sonof...@googlegroups.com>
Emmanuel Chryssagis
I have started from RESET CONFIGURATION and at the clean setup I set CONFIGURE MODUEL to generic (0). Then from menu CONFIGURE TEMPLATE I changed all parameters as in SONOFF T1 2CH (29). After restart I got the same condition. Disappointing. Any other idea ?
Emmanuel
Philip Knowles
man.ch...@gmail.com
I am afraid I don’t know the script code to make it from the OTHER menu.
man.ch...@gmail.com
Of course I can read the script code from a working switch and I can copy it to the problematic. What do you think?
Emmanuel Chryssagis
Emmanuel Chryssagis
Jéro
To view this discussion on the web, visit https://groups.google.com/d/msgid/sonoffusers/02d37c55-73f0-4e08-8935-a864392f206cn%40googlegroups.com.
Philip Knowles
PulseTime affects the outputs and automatically switches the output off – pulsetime1 2 will make output 1 switch off after 0.2s
From: Jéro
Sent: 15 August 2022 15:28
To: Emmanuel Chryssagis
Cc: TasmotaUsers
Subject: Re: Issues when flashing some two gang TXT2EU Sonoff switches
Have you tried to increase pulsetime from console.
exemple:
pulsetime1 2
Le lun. 15 août 2022 à 10:02, Emmanuel Chryssagis <man.ch...@gmail.com> a écrit :
Do you think that Tasmota version may affect the flashing with problem?
On Monday, August 15, 2022 at 10:59:36 AM UTC+3 Emmanuel Chryssagis wrote:
I have an other 3 brand new from the box switches and now I am afraid to flash them
On Monday, August 15, 2022 at 10:49:04 AM UTC+3 Emmanuel Chryssagis wrote:
Of course I can read the script code from a working switch and I can copy it to the problematic. What do you think?
From: Philip Knowles <knowles...@gmail.com>
Sent: Monday, 15 August, 2022 10:45
To: Emmanuel Chryssagis <man.ch...@gmail.com>; TasmotaUsers <sonof...@googlegroups.com>
Subject: Re: Issues when flashing some two gang TXT2EU Sonoff switches
Ignore the template. Deactivate it and make the changes in Configure Module page. It's too easy to make a mistake in the Template which is really difficult to spot.
From: sonof...@googlegroups.com <sonof...@googlegroups.com> on behalf of Emmanuel Chryssagis <man.ch...@gmail.com>
Sent: Monday, August 15, 2022 8:41:19 AM
To: TasmotaUsers <sonof...@googlegroups.com>
Subject: Re: Issues when flashing some two gang TXT2EU Sonoff switches
I have started from RESET CONFIGURATION and at the clean setup I set CONFIGURE MODUEL to generic (0). Then from menu CONFIGURE TEMPLATE I changed all parameters as in SONOFF T1 2CH (29). After restart I got the same condition. Disappointing. Any other idea ?
Emmanuel
On Monday, August 15, 2022 at 10:02:35 AM UTC+3 knowles...@gmail.com wrote:
Once you Activate it sets the Configuration. De-activating doesn't change the Configuration but only allows you to make changes in the Configuration window.
Leave it de-activated go to Configure Module and change the module to Generic. After it restarts put in the GPIO settings from the Template. See what happens after the restart.
From: man.ch..@gmail.com <man.ch...@gmail.com>
Sent: Monday, August 15, 2022 6:32:45 AM
To: 'Philip Knowles' <knowles...@gmail.com>; 'TasmotaUsers' <sonof...@googlegroups.com>
Subject: RE: Issues when flashing some two gang TXT2EU Sonoff switches
Philip I forgot to mention that I was experimenting with the code (numbers) in the top menu in the OTHER by trying to change the code addresses. I managed to control channel 1 from the second touch pad but nothing more. It is like the channel 1 touch pad is dead for control but as I mentioned it is responding with a beep when I touch it for long periods.
Emmanuel
From: Philip Knowles <knowles...@gmail.com>
Sent: Monday, 15 August, 2022 08:18
To: Emmanuel Chryssagis <man.ch...@gmail.com>; TasmotaUsers <sonof...@googlegroups.com>
Subject: Re: Issues when flashing some two gang TXT2EU Sonoff switches
You have still missed the Configure Other page. It looks like you have a Template entered but I don't know if it is activated
To view this discussion on the web, visit https://groups.google.com/d/msgid/sonoffusers/CAK%2BVJV1yAdt9Ri4kxLM8L1qrs6owGqYOditTdvGE%2B9O4UbVU6Q%40mail.gmail.com.