inspecting chainplates on 1987 P31-2

[Mike Butler]

Hello there,

This spring my "to do' list includes inspecting the chainplates. Something I've never done before. There is no  corrosion above deck. Below deck there is a bit of rust/corrosion on one bolt on the starboard side, while the port side has no evidence of corrosion.Can anyone recommend any youtube videos or articles about the best approach?

Has anyone in the group inspected their chainplates and found corrosion severe enough to warrant replacement?

And if I have gone to all the trouble of removing the chainplates so I can check the section that is between the deck and cabin liner is it better to just go ahead and have new chainplates fabricated?

Thanks very much for any guidance and tips.

Mike Butler

"Vela"

1987 P31-2

Weymouth, MA

[Guy Johnson]

I pulled the chainplates on Puffin, polished, inspected and reinstalled. 

Before reinstalling I de-cored the surrounding deck and made new deck plates from 1/4" fiberglass. 

If you can see any indications of crevice corrosion (thin lines of corrosion on the surface or deep pits) I would have new chainplates made. 

Guy

Puffin 10M #6

Sent from Outlook

---

From: pearso...@googlegroups.com <pearso...@googlegroups.com> on behalf of Mike Butler <mikebut...@gmail.com>
Sent: Wednesday, February 18, 2026 10:45 AM
To: pearson-boats <pearso...@googlegroups.com>
Subject: [pearson] inspecting chainplates on 1987 P31-2

 

--
You received this message because you are subscribed to the Google Groups "pearson-boats" group.
To unsubscribe from this group and stop receiving emails from it, send an email to pearson-boat...@googlegroups.com.
To view this discussion visit https://groups.google.com/d/msgid/pearson-boats/374a6b9f-b2fc-4bb0-9465-12833e095f3fn%40googlegroups.com.

[George Dubose]

Well, if you want the best approach to replacing chainplates, I would watch Sailing Uma on YouTube, episode 474.

One doesn't have to go as far as they did, but there are some very useful tips on reinstalling and stopping leaks.

George/Skylark

--
You received this message because you are subscribed to the Google Groups "pearson-boats" group.
To unsubscribe from this group and stop receiving emails from it, send an email to pearson-boat...@googlegroups.com.
To view this discussion visit https://groups.google.com/d/msgid/pearson-boats/374a6b9f-b2fc-4bb0-9465-12833e095f3fn%40googlegroups.com.

-- 
George DuBose
www.george-dubose.com

Wiedstrasse 16
D-50859 Cologne
Germany

[David Lidrbauch]

As Guy described.   You will need to pull them to determine whether good or needs replacement.   It's worth having them checked by a shop who can magnaflux or otherwise check for hidden crevice corrosion not otherwise visible...

-David Lidrbauch

--

[Kevin O’Brien]

Any corrosion condemns the chainplates. It’s not worth risking the rig; if you can see it, it’s time.

Kevin O'Brien

--

[Edward Criscuolo]

I would go one step further. If you remove them, you should replace them. After all, some of our Pearsons are 50 years old!  The shroud chain plates are simple flat bar stock, inexpensive to make. Then it’s good for another 50 years! 

@(^.^)@ Ed

Sent from my iPhone

On Feb 18, 2026, at 2:16 PM, Kevin O’Brien <kevin.mor...@gmail.com> wrote:



To view this discussion visit https://groups.google.com/d/msgid/pearson-boats/CA%2B1Pabxwd89eXs%2B%3D4HZdEeRiOZYdJbunqCJKJi2BSDOr%2B-Yc6g%40mail.gmail.com.

[Dave Cole]

Nah, inspect, replace if required.  If they have held up for 50 years, they will likely last another 25.  

Buying stainless of guaranteed quality is not that easy. 

To view this discussion visit https://groups.google.com/d/msgid/pearson-boats/CA309A50-2FAD-424F-A63C-C381C62A088A%40chessie.com.

[David Lidrbauch]

If you do need new

Metal supermarket in Woburn MA

Choose your metal type and grades and they will cut to your dimensions.   

Fairly fast and affordable

-David Lidrbauch

To view this discussion visit https://groups.google.com/d/msgid/pearson-boats/CAD5jJo3OqkkPg-mV_yEbNrg82LD5e3Y2%2Bh3CCsJdBpf8TjP0Fw%40mail.gmail.com.

[Kevin O’Brien]

I’m not sure this is the right approach.

Crevice corrosion occurs where stainless is exposed to water in a low-oxygen environment - and it’s microscopic. Failure is sudden and severe, it cannot be predicted, and it will bring your rig down.

Boats have been lost for failed chainplates, and assuming that the metal - which experienced cyclical loading for a quarter century - will last is foolhardy.

New 316L plates will give you at least a decade. Failing to replace your chainplates could result in a denied insurance claim, if they are found to be that old and not replaced. They could sink your boat. They could kill you or another person.

Spend the money and replace them. A full set of exceptionally oversized plates cost me $4500 just this past summer - it’s not that much, I imagine, on a much smaller Pearson.

Kevin O'Brien

To view this discussion visit https://groups.google.com/d/msgid/pearson-boats/CAD5jJo3OqkkPg-mV_yEbNrg82LD5e3Y2%2Bh3CCsJdBpf8TjP0Fw%40mail.gmail.com.

[Guy Johnson]

$4500.00 ??? I do hope you forgot a decimal point somewhere in there. 

If you're really worried, you can use dye to help expose flaws. 

Guy

Sent from Outlook

---

From: pearso...@googlegroups.com <pearso...@googlegroups.com> on behalf of Kevin O’Brien <kevin.mor...@gmail.com>
Sent: Wednesday, February 18, 2026 6:50 PM
To: pearso...@googlegroups.com <pearso...@googlegroups.com>
Subject: Re: [pearson] inspecting chainplates on 1987 P31-2

 

To view this discussion visit https://groups.google.com/d/msgid/pearson-boats/CA%2B1PabxO6OWz8azYn%2BEYU_au%2B%3DduVetnjeJqVgt3zJGFafUHbw%40mail.gmail.com.

[Dave Cole]

The problem is that the 316 you think you are buying may not be.

There has been big issues for years regarding inferior stainless.

So are you sure you are really getting 316L?  

I know the owner of one of the biggest fab shops in the midwest and this is a big issue.  The only way they reliably get around this is by buying from very reputable suppliers who supply traceable materials.  

To view this discussion visit https://groups.google.com/d/msgid/pearson-boats/CA%2B1PabxO6OWz8azYn%2BEYU_au%2B%3DduVetnjeJqVgt3zJGFafUHbw%40mail.gmail.com.

[George Dubose]

One of the doomsayers wrote about the stress of cyclic loading.

I believe when the boat is in the water and sailing the loading on the stays, shrouds and chainplates is much different than when the boat is on the hard with her mast standing. Owners who are too cheap or lazy to have their mast unstepped in the fall and store their boats on land are inviting this problem of cyclic loading and metal fatigue.

I also think that one if the biggest causes of mast failure is unmaintained or improperly tuned standing rigging.

George/Skylark

To view this discussion visit https://groups.google.com/d/msgid/pearson-boats/CA%2B1Pabxwd89eXs%2B%3D4HZdEeRiOZYdJbunqCJKJi2BSDOr%2B-Yc6g%40mail.gmail.com.

[Kevin O’Brien]

Yes, $4500. I worked with a fabricator that I know and trust, and had 6 1/2” thick 316L custom external plates made, with countersunk bolt holes cut to the shoulder profile for 8 316 socket head bolts, run through to 1/2” G10 backing plates, epoxied to the interior of the hull. Each plate was electro and then hand polished, and I passivated them prior to final installation.

In my case, my brother in law is a robotics engineer, and had an existing relationship with the metal fabricator in question, which made it easier to find a trustworthy source.

It is your boat. Do as you like. Being aware of the failure points for stainless does not make one a doomsayer.

Kevin O'Brien

To view this discussion visit https://groups.google.com/d/msgid/pearson-boats/ab5aa70f-80e4-6b9b-45bb-ac740dc66f43%40george-dubose.com.

[Jeff Griglack]

If you really want to not have to deal with crevice corrosion in the future, you probably should do what the late Patric Childress did on his boat "Brick House."  He replaced the SS chain plates with Titanium alloy.  Here is an article about it:  https://whereisbrickhouse.com/2019/10/25/titanium-chainplates-on-sailboats/

------------------------------------------------------------------
| Jeff Griglack             "Jabberwocky" P-365 #269

------------------------------------------------------------------
| "Don't take life so serious, son, it ain't nohow permanent"
|                   - Walt Kelly
| 'Years ago my mother used to say to me, she'd say, "In this
| world, Elwood, you must be" – she always called me Elwood –
| "In this world, Elwood, you must be oh so smart or oh so pleasant."
| Well, for years I was smart. I recommend pleasant. You may quote me.'
|               —James Stewart as Elwood P. Dowd
------------------------------------------------------------------

To view this discussion visit https://groups.google.com/d/msgid/pearson-boats/CA%2B1Pabz317kP1a%3DvSMa4U0L6De6G8MB1bz-LyqCZq_mY%3DybEXw%40mail.gmail.com.

[Dave Cole]

The biggest issue I have seen are deck leaks that rot bulkheads.  Then the chainplates are ripped right out of the bulkhead and through the deck. 

Dave

10M #26

To view this discussion visit https://groups.google.com/d/msgid/pearson-boats/ab5aa70f-80e4-6b9b-45bb-ac740dc66f43%40george-dubose.com.